DLA MIL-DTL-38999 10 B-2012 CONNECTORS ELECTRICAL CIRCULAR RECEPTACLE DUMMY STOWAGE BAYONET COUPLING (MIL-DTL-27599 SERIES II AND MIL-DTL-38999 SERIES II).pdf

《DLA MIL-DTL-38999 10 B-2012 CONNECTORS ELECTRICAL CIRCULAR RECEPTACLE DUMMY STOWAGE BAYONET COUPLING (MIL-DTL-27599 SERIES II AND MIL-DTL-38999 SERIES II).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-38999 10 B-2012 CONNECTORS ELECTRICAL CIRCULAR RECEPTACLE DUMMY STOWAGE BAYONET COUPLING (MIL-DTL-27599 SERIES II AND MIL-DTL-38999 SERIES II).pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, RECEPTACLE, DUMMY STOWAGE, BAYONET COUPLING, (MIL-DTL-27599, SERIES II AND MIL-DTL-38999, SERIES II) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the p

2、roduct described herein shall consist of this specification sheet and MIL-DTL-38999. FIGURE 1. Dummy receptacle, finishes B and X. AMSC N/A FSC 5935 MIL-DTL-38999/10B 15 June 2012 SUPERSEDING MIL-DTL-38999/10A 12 July 2002 INCH - POUND Provided by IHSNot for ResaleNo reproduction or networking permi

3、tted without license from IHS-,-,-MIL-DTL-38999/10B 2 DETAIL A Dimensions Shell size R BSC S max T dia +.010 -.005 X (TYP) Y (TYP) 8 .297 .828 82 118 10 .3595 .954 72 128 12 .406 1.047 68 132 14 .453 1.141 .120 66 134 16 .4845 1.234 70 130 18 .531 1.328 70 130 20 .578 1.453 70 130 22 .625 1.578 74 1

4、26 24 .6875 1.703 .147 74 126 FIGURE 1. Dummy receptacle, finishes B and X - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-38999/10B 3 Inch mm Inch mm Inch mm .005 0.13 .297 7.54 8.28 21.03 .010 0.25 .3595 9.13 9.54 24.23 .011 0.

5、28 .406 10.31 1.047 26.59 .015 0.38 .451 11.46 1.141 28.98 .058 1.47 .453 11.51 1.234 31.34 .063 1.60 .531 13.49 1.328 33.73 .120 3.05 .578 14.68 1.453 36.91 .147 3.73 .625 15.88 1.578 40.08 .222 5.64 .6875 17.46 1.703 43.26 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for inf

6、ormation only and are based upon 1 inch = 25.4 mm. 3. The gage features for GG shall be .010 inch (.25 mm) smaller than the MMC size at basic location. 4. Flange is solid. 5. Dummy receptacles are used when unmated plugs must be protected. FIGURE 1. Dummy receptacle, finishes B and X - Continued. Pr

7、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-38999/10B 4 REQUIREMENTS: Dimensions and configuration: See figure 1. Interface dimensions shall conform to MIL-DTL-38999, except as noted. Material: Shell: Aluminum alloy as specified in MIL-DTL-

8、38999 with finishes B or X. Sealing gasket: Non-corrosive silicone or fluorosilicone elastomer. This receptacle mates with MS27473, MS27480, MS27484 and MS27500. Fits all polarization positions. Part or Identifying Number (PIN) example: M38999/10 10 B Specification sheet number Shell size Finish NOT

9、E: The term PIN is equivalent to the term (part number, identification number, and type designator) which was previously used in this specification. Qualification: Qualification shall consist of the dynamic salt spray test, altitude immersion, coupling torque, coupling pin strength, and visual and m

10、echanical inspection as specified in MIL-DTL-38999, conducted on two samples of each shell size. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition t

11、o MIL-DTL-38999, this document references the following: MIL-DTL-27599 MS27473 MS27480 MS27484 MS27500 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-38999/10B 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - A

12、S Air Force - 85 (Project 5935-2012-042) DLA - CC Review activities: Army - AR, MI Navy - EC, MC, OS Air Force - 19, 99 DLA - IS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-