DLA MIL-DTL-32434 9-2013 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE CONVOLUTED PERMANENTLY ATTACHED FITTINGS HIGH TEMPERATURE MEDIUM PRESSURE FLARELESS-TO-FLANGE.pdf

《DLA MIL-DTL-32434 9-2013 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE CONVOLUTED PERMANENTLY ATTACHED FITTINGS HIGH TEMPERATURE MEDIUM PRESSURE FLARELESS-TO-FLANGE.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-32434 9-2013 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE CONVOLUTED PERMANENTLY ATTACHED FITTINGS HIGH TEMPERATURE MEDIUM PRESSURE FLARELESS-TO-FLANGE.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-DTL-32434/9 23 January 2013 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, CONVOLUTED, PERMANENTLY ATTACHED FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARELESS-TO-FLANGE This specification is approved for use by all Departments and Agencies of the Department of Defense. Th

2、e requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-32434. Hose assembly dimensions for style A: See figure 1. Fitting ends Hose size Dimensions 1 2 A (ref) B ( max) C (max) F (max) M (max) P (max) Straight Straight 8 .310 1.640 .880 1.014

3、1.560 .875 10 .356 1.940 .967 1.158 1.570 1.000 12 .393 1.913 1.122 1.447 1.640 1.250 16 .429 2.298 1.480 1.736 1.750 1.500 20 .393 2.577 1.750 2.328 1.990 1.844 24 .398 2.800 2.150 2.621 2.260 2.125 NOTES: 1. Style A uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dim

4、ensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 1. Style A hose assembly di

5、mensions. AMSC N/A FSC 4720 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 2 Hose assembly dimensions for style B: See figure 2. Fitting ends Hose size Dimensions 1 2 A (ref) B (max) C (max) D (max) F (max) N (max) P (max)

6、 R (min) R (max) Straight 45 8 .310 1.640 .880 1.722 1.014 .606 .875 .303 .428 10 .356 1.940 .967 2.037 1.158 .658 1.000 .340 .465 12 .393 1.913 1.122 2.368 1.447 .789 1.250 .433 .558 16 .429 2.298 1.480 2.583 1.736 .929 1.500 .470 .657 20 .393 2.577 1.750 2.946 2.328 1.020 1.844 .534 .721 24 .398 2

7、.800 2.150 3.210 2.621 1.186 2.125 .589 .839 NOTES: 1. Style B uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimension “N (max)”is an installation dimen

8、sions and not a design dimension. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 2. Style B hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permit

9、ted without license from IHS-,-,-MIL-DTL-32434/9 3 Hose assembly dimensions for style C: See figure 3. Fitting ends Hose size Dimensions 1 2 A (ref) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max) Straight 90 8 .310 1.640 .880 1.014 .875 2.320 1.422 .857 .982 10 .356 1.940 .967 1.158

10、 1.000 2.875 1.499 .861 1.015 12 .393 1.913 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16 .429 2.298 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20 .393 2.577 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24 .398 2.800 2.150 2.621 2.125 5.075 3.103 1.516 2.028 NOTES: 1. Style C uses class 1 fittings which

11、are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimension “T (max)”is an installation dimensions and not a design dimension. 5. Assembly length (see PIN) is based on end of MS8000 se

12、ries seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 3. Style C hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 4 Hose assembly dimensions for style D: Se

13、e figure 4. Fitting ends Hose size Dimensions A (ref) C (max) D (max) E (max) F (max) G (min) G (max) N (max) P (max) R (min) R (max) 1 2 45 45 8 .310 .880 1.722 1.426 1.014 .542 .789 .606 .875 .303 .428 10 .356 .967 2.037 1.596 1.158 .631 .877 .658 1.000 .340 .465 12 .393 1.122 2.368 1.739 1.447 .6

14、31 .952 .789 1.250 .433 .558 16 .429 1.480 2.583 1.931 1.736 .741 1.069 .929 1.500 .470 .657 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.020 1.844 .534 .721 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 1.186 2.125 .589 .839 NOTES: 1. Style D uses class 1 fittings which are made from corrosion resist

15、ant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimensions “E (max)” and “N (max)” are installation dimensions and not design dimensions. 4. Dimension “F” is measured across the corners. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face

16、 of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 4. Style D hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 5 Hose assembly dimensions for style E: See figure 5. Fitti

17、ng ends Hose size Dimensions A (ref) C (max) D (max) E (max) F (max) G (min) G (max) P (max) S (max) T (max) U (min) U (max) 1 2 45 90 8 .310 .880 1.722 1.426 1.014 .542 .789 .875 2.320 1.422 .857 .982 10 .356 .967 2.037 1.596 1.158 .631 .877 1.000 2.875 1.499 .861 1.015 12 .393 1.122 2.368 1.739 1.

18、447 .631 .952 1.250 3.606 1.807 1.032 1.246 16 .429 1.480 2.583 1.931 1.736 .741 1.069 1.500 3.981 2.174 1.156 1.434 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.844 4.435 2.590 1.344 1.715 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 2.125 5.075 3.103 1.516 2.028 NOTES: 1. Style E uses class 1 fitti

19、ngs which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimensions “E (max)” and “T (max)” are installation dimensions and not design dimensions. 4. Dimension “F” is measured across the corners. 5. Assembly length (see PIN) is ba

20、sed on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 5. Style E hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 6 Hose assembly dim

21、ensions for style F: See figure 6. Fitting ends Hose size Dimensions A (ref) C (max) F (max) H (max) J (max) K (min) K (max) P (max) S (max) T (max) U (min) U (max) 1 2 90 90 8 .310 .880 1.014 2.495 2.032 1.032 1.282 .875 2.320 1.422 .857 .982 10 .356 .967 1.158 2.955 2.437 1.357 1.607 1.000 2.875 1

22、.499 .861 1.015 12 .393 1.122 1.447 3.705 2.795 1.591 1.841 1.250 3.606 1.807 1.032 1.246 16 .429 1.480 1.736 4.100 3.160 1.741 1.991 1.500 3.981 2.174 1.156 1.434 20 .393 1.750 2.328 4.835 3.664 2.021 2.396 1.844 4.435 2.590 1.344 1.715 24 .398 2.150 2.621 5.480 4.251 2.403 2.778 2.125 5.075 3.103

23、1.516 2.028 NOTES: 1. Style F uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimensions “J (max)” and “T (max)” are installation dimensions and not desig

24、n dimensions. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 6. Style F hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

25、from IHS-,-,-MIL-DTL-32434/9 7 Hose assembly dimensions for style G: See figure 7. Fitting ends Hose size Dimensions 1 2 A (ref) C (max) D (max) E (max) F (max) G (min) G (max) M (max) P (max) 45 Straight 8 .310 .880 1.722 1.426 1.014 .542 .789 1.560 .875 10 .356 .967 2.037 1.596 1.158 .631 .877 1.5

26、70 1.000 12 .393 1.122 2.368 1.739 1.447 .631 .952 1.640 1.250 16 .429 1.480 2.583 1.931 1.736 .741 1.069 1.750 1.500 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.990 1.844 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 2.260 2.125 NOTES: 1. Style G uses class 1 fittings which are made from corrosion r

27、esistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “E (max)” is an installation dimension and not a design dimension. 4. Dimension “F” is measured across the corners. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flan

28、ge. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 7. Style G hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 8 Hose assembly dimensions for style H: See figure 8. Fitting ends

29、Hose size Dimensions 1 2 A (ref) C (max) F (max) H (max) J (max) K (min) K (max) M (max) P (max) 90 Straight 8 .310 .880 1.014 2.495 2.032 1.032 1.282 1.560 .875 10 .356 .967 1.158 2.955 2.437 1.357 1.607 1.570 1.000 12 .393 1.122 1.447 3.705 2.795 1.591 1.841 1.640 1.250 16 .429 1.480 1.736 4.100 3

30、.160 1.741 1.991 1.750 1.500 20 .393 1.750 2.328 4.835 3.664 2.021 2.396 1.990 1.844 24 .398 2.150 2.621 5.480 4.251 2.403 2.778 2.260 2.125 NOTES: 1. Style H uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal.

31、 3. Dimension “F” is measured across the corners. 4. Dimension “J (max)” is an installation dimension and not a design dimension. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 8. Sty

32、le H hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 9 Hose assembly dimensions for style J: See figure 9. Fitting ends Hose size Dimensions A (ref) C (max) D (max) F (max) H (max) J (max) K (min) K (max) N (

33、max) P (max) R (min) R (max) 1 2 90 45 8 .310 .880 1.722 1.014 2.495 2.032 1.032 1.282 .606 .875 .303 .428 10 .356 .967 2.037 1.158 2.955 2.437 1.357 1.607 .658 1.000 .340 .465 12 .393 1.122 2.368 1.447 3.705 2.795 1.591 1.841 .789 1.250 .433 .558 16 .429 1.480 2.583 1.736 4.100 3.160 1.741 1.991 .9

34、29 1.500 .470 .657 20 .393 1.750 2.946 2.328 4.835 3.664 2.021 2.396 1.020 1.844 .534 .721 24 .398 2.150 3.210 2.621 5.480 4.251 2.403 2.778 1.186 2.125 .589 .839 NOTES: 1. Style J uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end

35、of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimensions “J (max)” and “N (max)” are installation dimensions and not design dimensions 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/

36、1, see requirements. FIGURE 9. Style J hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 10 Hose assembly dimensions for style K: See figure 10. Fitting ends Hose size Dimensions 1 2 A (ref) B ( max) C (max) F

37、(max) M (max) P (max) Straight Straight 8 .310 1.640 .880 1.014 1.560 .875 10 .356 1.940 .967 1.158 1.570 1.000 12 .393 1.913 1.122 1.447 1.640 1.250 16 .429 2.298 1.480 1.736 1.750 1.500 20 .393 2.577 1.750 2.328 1.990 1.844 24 .398 2.800 2.150 2.621 2.260 2.125 NOTES: 1. Style K uses class 2 fitti

38、ngs which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5. Apply NAS1760 in accordance with MIL

39、-DTL-25579/1, see requirements. FIGURE 10. Style K hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 11 Hose assembly dimensions for style M: See figure 11. Fitting ends Hose size Dimensions 1 2 A (ref) B (max)

40、 C (max) D (max) F (max) N (max) P (max) R (min) R (max) Straight 45 8 .310 1.640 .880 1.722 1.014 .606 .875 .303 .428 10 .356 1.940 .967 2.037 1.158 .658 1.000 .340 .465 12 .393 1.913 1.122 2.368 1.447 .789 1.250 .433 .558 16 .429 2.298 1.480 2.583 1.736 .929 1.500 .470 .657 20 .393 2.577 1.750 2.9

41、46 2.328 1.020 1.844 .534 .721 24 .398 2.800 2.150 3.210 2.621 1.186 2.125 .589 .839 NOTES: 1. Style M uses class 2 fittings which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. D

42、imension “N (max)”is an installation dimensions and not a design dimension. 4. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 11. Style M hose assembly dimensions. Provided by IHSNot for

43、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 12 Hose assembly dimensions for style N: See figure 12. Fitting ends Hose size Dimensions 1 2 A (ref) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max) Straight 90 8 .310 1.640 .880 1.014 .875 2

44、.320 1.422 .857 .982 10 .356 1.940 .967 1.158 1.000 2.875 1.499 .861 1.015 12 .393 1.913 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16 .429 2.298 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20 .393 2.577 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24 .398 2.800 2.150 2.621 2.125 5.075 3.103 1.516 2.028 N

45、OTES: 1. Style N uses class 2 fittings which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimension “T (max)” is an installation dimension and not a design dimension. 5. Assembl

46、y length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 12. Style N hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32

47、434/9 13 Hose assembly dimensions for style P: See figure 13. Fitting ends Hose size Dimensions A (ref) C (max) D (max) E (max) F (max) G (min) G (max) N (max) P (max) R (min) R (max) 1 2 45 45 8 .310 .880 1.722 1.426 1.014 .542 .789 .606 .875 .303 .428 10 .356 .967 2.037 1.596 1.158 .631 .877 .658

48、1.000 .340 .465 12 .393 1.122 2.368 1.739 1.447 .631 .952 .789 1.250 .433 .558 16 .429 1.480 2.583 1.931 1.736 .741 1.069 0.929 1.500 .470 .657 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.020 1.844 .534 .721 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 1.186 2.125 .589 .839 NOTES: 1. Style P uses class 2 fittings which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimensions “E (max)” and “N (max)” are installation dimensions and not design dimensions. 4. Di