DLA MIL-DTL-32139 6-2012 CONNECTORS ELECTRICAL RECTANGULAR NANOMINIATURE SINGLE ROW RECEPTACLE POLARIZED SHELL SOCKET CONTACTS VERTICAL PCB THROUGH-HOLE TYPE.pdf

《DLA MIL-DTL-32139 6-2012 CONNECTORS ELECTRICAL RECTANGULAR NANOMINIATURE SINGLE ROW RECEPTACLE POLARIZED SHELL SOCKET CONTACTS VERTICAL PCB THROUGH-HOLE TYPE.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-32139 6-2012 CONNECTORS ELECTRICAL RECTANGULAR NANOMINIATURE SINGLE ROW RECEPTACLE POLARIZED SHELL SOCKET CONTACTS VERTICAL PCB THROUGH-HOLE TYPE.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-DTL-32139/6 1 August 2012 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, NANOMINIATURE, SINGLE ROW, RECEPTACLE, POLARIZED SHELL, SOCKET CONTACTS, VERTICAL PCB THROUGH-HOLE TYPE This specification is approved for use by all Departments and Agencies of the Department of

2、 Defense. The requirement for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-32139. FIGURE 1. Nano connector dimensions and configurations. AMSC N/A FSC 5935 B .025 A R .018 (RADIUS OPTIONAL) 4X CONTACTS C L #0-80 UNF-2B, 2X .010 SEE NOTE 6 SEE NOTE 4 TY

3、P (SEE NOTE 5) EPOXY FILLED .11 .010 TYP .150 .0135 .0000 .0015 + - .0185 .0000 .0015 + - .042 .037 .110 .003 .003/.005 X 45 .345 .115 .010 X C .0575 .010 X C Y X .004 X Y C .005 OF Y C .010 X Y D C TYP Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

4、-MIL-DTL-32139/6 2 Insert arrangement A B BSC C BSC D MAX 9 .500 (12.70) .395 (10.03) .285 (7.24) .295 (7.49) 15 .650 (16.51) .545 (13.84) .435 (11.05) .445 (11.30) 21 .800 (20.32) .695 (17.65) .585 (14.86) .595 (15.11) 25 .900 (22.86) .795 (20.19) .685 (17.40) .695 (17.65) 31 1.050 (26.67) .945 (24

5、.00) .835 (21.21) .845 (21.46) 37 1.200 (30.48) 1.095 (27.81) .985 (25.02) .995 (25.27) 51 1.550 (39.37) 1.445 (36.70) 1.335 (33.91) 1.345 (34.16) Inches .0015 .003 .004 .005 .010 .0135 .018 .0185 .025 .037 .042 .0575 .11 .115 .150 .345 .330 mm 0.038 0.08 0.10 0.13 0.25 0.34 0.46 0.47 0.64 0.94 1.07

6、 1.46 2.8 2.92 3.81 8.76 8.38 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances are .005 inch (0.13 mm) angular tolerance 2o. 4. Surface from which the lead length is measured. 5. Shell shall be flush to insulator withi

7、n .004 inch (0.10 mm). 6. Tail finish is tin/lead or gold. FIGURE 1. Nano connector dimensions and configurations Continued. INTERFACE DETAIL Inches .0015 .0345 .075 .085 mm 0.038 0.88 1.91 2.16 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless other

8、wise specified tolerances are .005 inch (.13 mm). FIGURE 2. Nano connector interface. C R.0345, 2X FULL R, 2X Y .075 .085 .0015 X C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32139/6 3 NOTES: 1. Engaging face of insert shown. 2. Cavity i

9、dentification numbers are for reference only and do not appear on the part. FIGURE 3. Nano connector insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32139/6 4 NOTES: 1. Suggested hole pattern shown facing board from connec

10、tor insertion side specified on figure 3. 2. Dimensions are in inches. 3. Metric equivalents are given for information only. 4. Unless otherwise specified tolerances are .005 inch (0.13 mm) angular tolerance 2o. FIGURE 4. Nano connector suggested PCB hole pattern. Inches mm .001 0.03 .002 0.05 .013

11、0.33 .016 0.41 .025 0.64 .050 .067 .073 1.27 1.70 1.85 .0975 2.477 Insert arrangement B BSC E 9 .395 (10.03) .200 (5.08) 15 .545 (13.84) .350 (8.89) 21 .695 (17.65) .500 (12.70) 25 .795 (20.19) .600 (15.24) 31 .945 (24.00) .750 (19.05) 37 1.095 (27.81) .900 (22.86) 51 1.445 (36.70) 1.250 (31.75) .05

12、0 .001 TYP. .025 .002 .0975 .002 E B .025 .001 TYP. .050 .001 TYP. .013/ .016 TYP. POSITION 1 .067/.073 2X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32139/6 5 REQUIREMENTS Dimensions and configuration see figures 1, 2, and 3. This speci

13、fication sheet describes the socket side of a rectangular connector. This connector uses reverse gender contacts, i.e., the live pin is recessed in the insulator with the static socket protruding from a shrouded interface. Contact connection: The socket contact, which is exposed in the insulator, is

14、 normally connected to the neutral side of the circuit. Sockets are terminated to a printed circuit board (PCB) as specified on figure 4. Mating receptacle: Shall be in accordance with MIL-DTL-32139/5 Part or Identifying Number (PIN): M 32139/ 06- A 01 S N S Space class Shell and finish Hardware Tai

15、l Finish Insert arrangement Detailed specification sheet Basic specification number M prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32139/6 6 Insert Arrangement A = 9 B = 15 C = 21 D = 25 E = 31 F = 37 G = 51 Tail Finish 01 = Tin/Lea

16、d 02 = Gold Hardware 1/ T = Threaded hole Shell and Finish C = Aluminum shell, cadmium finish N = Aluminum shell, electroless nickel finish 2/ S = Passivated stainless steel shell T = Titanium shell A = Pure Electrodeposited Aluminum F = Nickel Fluorocarbon Polymer Z = Zinc Nickel Space class Blank

17、for non-space applications S = Space class 1/ Supplied installed. 2/ When aluminum shells are required for space applications, electroless nickel shall be used. Cadmium finish is not acceptable (see MIL-DTL-32139). Alternate shell finishes: Pure Electrodeposited Aluminum. Pure dense electrodeposited

18、 aluminum shall be in accordance with MIL-DTL-83488, type II shall withstand 48 hour salt spray. Color shall be non-reflective and shall meet the requirements as specified herein. Nickel Fluorocarbon Polymer. High phosphate nickel with fluorocarbon polymer additive over a suitable underplate shall b

19、e able shall withstand 48 hour salt spray. Color shall be non-reflective and shall meet the requirements as specified herein. Zinc Nickel. Zinc Nickel Alloy shall be in accordance with ASTM B841, over a suitable underplate shall withstand 48 hour salt spray. Color shall be non-reflective and shall m

20、eet the requirements as specified herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32139/6 7 Referenced documents: In addition to MIL-DTL-32139, this document references the following: MIL-DTL-32139/5 MIL-DTL-83488 ASTM B841 CONCLUDING

21、 MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2010-201) DLA - CC Review activities: Army - AV, MI Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-