DLA MIL-DTL-28791 1 C-2011 ISOLATORS RADIO FREQUENCY COAXIAL.pdf
《DLA MIL-DTL-28791 1 C-2011 ISOLATORS RADIO FREQUENCY COAXIAL.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-28791 1 C-2011 ISOLATORS RADIO FREQUENCY COAXIAL.pdf(13页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 5985MIL-DTL-28791/1C 10 March 2011 SUPERSEDING MIL-DTL-28791/1B 20 September 2006 DETAIL SPECIFICATION SHEET ISOLATORS, RADIO FREQUENCY, COAXIAL This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the produc
2、t listed herein shall consist of this specification sheet and MIL-DTL-28791. NOTES: 1. See table I for dimensions. 2. All un-dimensioned pictorial representations are for reference purposes only. FIGURE 1. Dimensions and configurations for dash numbers 001, 002, 003, 004, 005, 016, 017, 020, 022, 02
3、3, 024, 025, 030, 031, and 035. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28791/1C 2 STRIPLINE TERMINAL TABS PROTRUSION FROM CASE WHEN INPUT AND OUTPUT PORT CONNECTORS ARE REMOVED. SHIM CONNECTOR MOUNTINGS AS REQUIRED. NOTES:
4、 1. See table I for dimensions. 2. All un-dimensioned pictorial representations are for reference purposes only. 3. Metric equivalents are in parentheses. FIGURE 2. Dimensions and configurations for dash numbers 006, 010, and 014. Provided by IHSNot for ResaleNo reproduction or networking permitted
5、without license from IHS-,-,-MIL-DTL-28791/1C 3 NOTES: 1. See table I for dimensions. 2. All un-dimensioned pictorial representations are for reference purposes only. FIGURE 3. Dimensions and configurations for dash numbers 007, 009, 011, 012, and 027. Provided by IHSNot for ResaleNo reproduction or
6、 networking permitted without license from IHS-,-,-MIL-DTL-28791/1C 4 NOTES: 1. See table I for dimensions. 2. All un-dimensioned pictorial representations are for reference purposes only. FIGURE 4. Dimensions and configurations for dash numbers 008, 013, 015, 018, 019, 021, 028, and 033. Provided b
7、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28791/1C 5 NOTES: 1. See table I for dimensions. 2. All un-dimensioned pictorial representations are for reference purposes only. FIGURE 5. Dimensions and configurations for dash numbers 026 and 032. Prov
8、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28791/1C 6 NOTES: 1. See table I for dimensions. 2. All un-dimensioned pictorial representations are for reference purposes only. FIGURE 6. Dimensions and configurations for dash numbers 029 and 034
9、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dimensional and thread requirements. Dash no. Dimensions 1/ 2/ A B C D E F G H J Max Max Min Max Min Max Min Max Max Max Min Max Min Max -001 .66 (16.8) .53 (13.5) .345 (8.76) .355 (9.02) .40
10、7 (10.34) .417 (10.59) .070 (1.78) .080 (2.03) .53 (13.5) .135 (3.43) .220 (5.59) .415 (10.54) .245 (6.22) .255 (6.48) -002 .66 (16.8) .53 (13.5) .345 (8.76) .355 (9.02) .407 (10.34) .417 (10.59) .070 (1.78) .080 (2.03) .53 (13.5) .135 (3.43) “ “ .245 (6.22) .255 (6.48) -003 1.055 (26.80) .955 (24.2
11、6) .645 (16.38) .655 (16.64) .395 (10.03) .405 (10.29) .145 (3.68) .155 (3.94) .65 (16.5) .27 (6.9) “ “ .245 (6.22) .255 (6.48) -004 1.055 (26.80) .955 (24.26) .645 (16.38) .655 (16.64) .395 (10.03) .405 (10.29) .145 (3.68) .155 (3.94) .65 (16.5) .27 (6.9) “ “ .245 (6.22) .255 (6.48) -005 1.20 (30.5
12、) 1.20 (30.5) .945 (24.00) .955 (24.26) .395 (10.03) .405 (10.29) .125 (3.18) .135 (3.43) .75 (19.0) .17 (4.3) “ “ .255 (6.48) .265 (6.73) -006 1.25 (31.8) 1.25 (31.8) .645 (16.38) .655 (16.64) .295 (7.49) .305 (7.75) .75 (19.0) .17 (4.3) “ “ .295 (7.49) .305 (7.75) -007 1.50 (38.1) 1.50 (38.1) .995
13、 (25.27) 1.005 (25.53) .245 (6.22) .255 (6.48) .63 (16.0) .27 (6.9) “ “ .265 (6.73) .275 (6.98) -008 2.75 (69.8) 2.75 (69.8) 1.995 (50.67) 2.005 (50.93) .495 (12.57) .505 (12.83) .89 (22.6) .69 (17.5) “ “ .399 (10.13) .349 (8.86) -009 1.25 (31.8) 1.25 (31.8) .995 (25.27) 1.005 (25.53) .115 (2.92) .1
14、25 (3.18) .63 (16.0) .27 (6.9) “ “ .245 (6.22) .255 (6.48) -010 1.500 (38.10) 1.49 (37.8) .995 (25.27) 1.005 (25.53) .245 (6.22) .255 (6.48) .65 (16.5) .17 (4.3) “ “ .275 (6.98) .285 (7.24) -011 1.25 (31.8) 1.25 (31.8) .995 (25.27) 1.005 (25.53) .115 (2.92) .125 (3.18) .63 (16.0) .27 (6.9) “ “ .245
15、(6.22) .255 (6.48) -012 2.00 (50.8) 2.00 (50.8) 1.713 (43.51) 1.723 (43.76) .135 (3.43) .145 (3.68) 1.00 (25.4) .27 (6.9) “ “ .495 (12.57) .505 (12.83) -013 1.70 (43.2) 1.63 (41.4) 1.115 (28.32) 1.125 (28.58) .245 (6.22) .255 (6.48) .75 (19.0) .27 (6.9) “ “ .349 (8.86) .355 (9.02) -014 1.72 (43.7) 1
16、.65 (41.9) 1.045 (26.54) 1.055 (26.80) .295 (7.49) .305 (7.75) .75 (19.0) .17 (4.3) “ “ .335 (8.51) .345 (8.76) -015 2.08 (52.8) 1.77 (45.0) 1.095 (27.81) 1.105 (28.07) .325 (8.26) .335 (8.51) .99 (25.1) .17 (4.3) “ “ .275 (6.98) .285 (7.24) -016 1.625 (41.28) 1.625 (41.28) 1.320 (33.53) 1.330 (33.7
17、8) .807 (20.50) .817 (20.75) .120 (3.05) .130 (3.30) .75 (19.0) .27 (6.9) “ “ .370 (9.40) .380 (9.65) -017 1.625 (41.28) 1.625 (41.28) 1.320 (33.53) 1.330 (33.78) .807 (20.50) .817 (20.75) .120 (3.05) .130 (3.30) .75 (19.0) .27 (6.9) “ “ .370 (9.40) .380 (9.65) See footnotes at end of table I. MIL-D
18、TL-28791/1C7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dimensional and thread requirements - Continued. Dash no. Dimensions - Continued. 1/ 2/ K L MTG threads Connectors Figure no. Min Max Min Max -001 .086-56 UNC-2B x.13DP 2 females 1
19、-002 .086-56 UNC-2B x .13DP 2 females 1 -003 .112-40 UNC-2B x .15DP 2 females 1 -004 .112-40 UNC-2B x .15DP 2 females 1 -005 .086-56 UNC-2B x .13DP 2 females 1 -006 .145 (3.68) .155 (3.94) .995 (25.27) 1.005 (25.53) .086-56 UNC-2B x .30DP 2 females 2 -007 .145 (3.68) .155 (3.94) 1.182 (30.02) 1.192
20、(30.28) .112-40 UNC-2B x .13DP 2 females 3 -008 .399 (10.13) .349 (8.86) 1.995 (50.67) 2.005 (50.93) .112-40 UNC-2B x .19DP 2 females 4 -009 .115 (2.92) .125 (3.18) .995 (25.27) 1.005 (25.53) .086-56 UNC-2B x .13DP 1 female and 1 male 3 -010 .115 (2.92) .125 (3.18) .995 (25.27) 1.005 (25.53) .086-56
21、 UNC-2B x .13DP 2 females 2 -011 .115 (2.92) .125 (3.18) .995 (25.27) 1.005 (25.53) .086-56 UNC-2B x .13DP 1 female and 1 male 3 -012 .135 (3.43) .145 (3.68) 1.713 (43.51) 1.723 (43.76) .112-40 UNC-2B x .15DP 2 females 3 -013 1.075 (27.30) 1.085 (27.56) .349 (8.86) .355 (9.02) .112-40 UNC-2B x .15DP
22、 2 females 4 -014 .335 (8.51) .345 (8.76) 1.0495 (26.657) 1.0505 (26.683) .112-40 UNC-2B x .15DP 2 females 2 -015 .345 (8.76) .355 (9.02) 1.395 (35.43) 1.405 (35.69) .112-40 UNC-2B x .15DP 2 females 4 -016 .112-40 UNC-2B x .15DP 2 females 1 -017 .112-40 UNC-2B x .15DP 2 females 1 See footnotes at en
23、d of table I. 8MIL-DTL-28791/1CProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dimensional and thread requirements - Continued. Dash no. Dimensions 1/ 2/ A B C D E F G H J Max Max Min Max Min Max Min Max Max Max Min Max Min Max -018 1.00 (25
24、.4) 1.00 (25.4) .795 (20.19) .805 (20.45) .095 (2.41) .105 (2.67) .50 (12.7) .17 (4.3) .220 (5.59) .415 (10.54) .245 (6.22) .255 (6.48) -019 1.06 (26.9) 1.00 (25.4) .745 (18.92) .755 (19.18) .115 (2.92) .125 (3.18) .75 (19.0) .27 (6.9) “ “ .245 (6.22) .255 (6.48) -020 1.03 (26.2) 1.00 (25.4) .595 (1
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL287911C2011ISOLATORSRADIOFREQUENCYCOAXIALPDF

链接地址:http://www.mydoc123.com/p-690423.html