DLA MIL-DTL-27546 E-2000 LINER FLYER-S JACKET AND FLYERS TROUSERS CWU-9 P《CWU-9 P型飞行员外套和飞行员裤子系列》.pdf

《DLA MIL-DTL-27546 E-2000 LINER FLYER-S JACKET AND FLYERS TROUSERS CWU-9 P《CWU-9 P型飞行员外套和飞行员裤子系列》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-27546 E-2000 LINER FLYER-S JACKET AND FLYERS TROUSERS CWU-9 P《CWU-9 P型飞行员外套和飞行员裤子系列》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、I INCH-POUND I Beneficial comments, (recommendations, additions, deletions) and any data which may be of use in approving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-COCT, building 6-1 -D, 700 Robbins Ave, Philadelphia, PA 1

2、9 1 1 1-5096 by using the self addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. MIL-DTL-27546E July 26,2000 SUPERSEDING MIL-L-27546D (US AF) DETAIL SPECIFICATION LINER: FLYERS JACKET, AND FLYERS TROUSERS, CWU-9/P The General S

3、ervices Administration has authorized the use of this specification for all Federal agencies. 1. SCOPE 1.1 Scope. This Specification covers the requirements for liners to be worn under the CWU-91P jacket and trousers. 1.2 Classification The jacket and trouser liners are furnished in the following si

4、zes: Small 34 - 36 Medium 38 - 40 Large 42 - 44 Extra-Large 46 - 48 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27546E 2. APPLICABLE DOCUMENTS 2.1 General.

5、The documents listed in this section are specified in sections 3 and 4. This section does not include documents cited in other sections or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned tha

6、t they must meet all specified requirements and documents cited in sections 3 and 4, whether or not they are listed. 2.2 Government Documents 2.2.1 Specifications, standards, and handbooks The following specifications, standards, and handbooks form a part of this document to the extent specified her

7、ein. Unless otherwise specified, the issues of these documents will be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.1). SPECIFICATIONS FEDERAL A-A-55634 Fastener, Slide, Interlocking A-A

8、-52094 Thread, Cotton MILITARY MIL-F-10884 Fasteners, Snap MIL-B-4 1826 Batting, Synthetic Fibers, Polyester (Unquilted and Quilted). (Unless otherwise indicated, copies of Federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, Bldg.

9、 4D, 700 Robbins Avenue, Philadelphia, PA 19 1 1 1-5096.) 2.3 Non-Government Publications The following document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cit

10、ed in the specification. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) / AMERICAN SOCIETY for QUALITY (ASO) ANSUASQC Z1.4 Sampling Procedures and Tables for Inspection of Attributes. Application for copies should be addressed to American National Standards Institute, 11 West 42nd Street, New York, NY

11、 10036-8002. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) PUBLICATION 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27546E ASTM-D-3776 Mass Per Unit Area (Weight) of Fabric (Application for copies should be addressed to American Soci

12、ety for Testing and Materials, 1 O0 Barr Harbour Drive, West Conshohocken, PA 19428) AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC-6 1 Colorfastness to Laundry, Home and Commercial: Accelerated (Applications for copies should be addressed to American Association of Textile Che

13、mists and Colorists (AATCC) PO Box 12215, Triangle Park, NC 27709-2215) 2.4 Order of precedence. In the event of conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document however, supersedes applicable laws and re

14、gulations unless a specified exemption has been obtained . 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.2. 3.2 Recycled recovered or environmentally preferable materials Recycled, recovered, or env

15、ironmentally preferable material should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.3 Description. 3.3.1 Jacket liner. The jacket liner shall have a center

16、front opening with slide fastener and four snaps concealed by an outside flap, knit collarette and cuffs, and a patch pocket on the outside left breast measuring 5 inches wide and 5-5/8 inches deep. The hanger loop, 1/2 inch by 3 inches long, shall be caught in the seaming of the collar to the neck

17、and secured with a bartack. 3.3.2 Trouser liner. The trouser liner shall have an elastic waistband, snap fly closure, knit anklets and back hip patch pockets measuring 6-1/4 inches wide and 6 inches deep. The hangers for the trousers shall be centered on the seat seam with a bartack 1/4 inch below t

18、he bottom edge of the waistband. 3.3.3 Seams and stitching All raw edges including the pocket shall be overedge stitched (6- 1 O stitches per inch). Top corners of all pocket openings and the bottom of the fly shall be bartacked. All seams shall be lock or chain stitched (10-14 stitches per inch) wi

19、th the edges overedged together. In addition, the seat seam shall be raise stitched with a double needle machine with the right overlapping the left. The waistband shall be 2 inches wide with four rows evenly spaced stitching. The top edge of the slide fastener tape (without teeth) shall be exposed

20、3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27546E approximately 3/4 inch (to make room for the snap) and shall be caught in the collar seaming on the jacket liner. 3.4 Materials. 3.4.1 Basic material. The quilted material with a nylon

21、taffeta cover shall conform to Type VIII, cover D, Style a and Class 9 of MIL-B-4 1826. The color shall be USAF Sage Green USAF color shade 1511. 3.4.2 Knit cloth for the Anklets wristlets, and collarette The color of the knit cloth shall be constructed to have not less than 14 wales per inch and no

22、t less than 18 courses per inch. Three courses of single, cotton shall alternate with one course of 2-ply spun nylon yarn. The knit cloth shall be a good match to the basic material. The finished cloth shall show colorfastness to laundering (after 3 test cycles) equal to or better than the standard

23、sample, or a rating of 3-4”or better on the AATCC Gray scale for Color Change when compared to the unlaundered sample when tested in accordance with paragraph 4.5. The anklets and wristlets shall conform to the characteristics outlined in Table I. 3.4.2.1 Anklets and wristlets The cloth shall be mad

24、e on a circular knitting machine with one end of yarn per feed using a 1 by 1 rib stitch, The ends shall have a tuck or expanding stitch (U2 inch minimum when folded and finished). TABLE I Anklets and Wristlets Weight Folded width Open length Anklets 12 ounces 3 9 Wristlets 9 ounces 2-1.2 9 (per doz

25、en pairs) (inches) (inches) (+/- 1/4 inch) (+/- 1/4 inch) 3.4.2.2 Collarettes. The cloth shall be made on a circular knitting machine or on a flat-bed knitting machine using 1 by 1 rib stitch with one end per feed. Three courses of single, cotton yarn shall alternate with one course of 2 ply spun ny

26、lon yarn. The weight of the cloth shall be not less than 12 ounces per square yard. 3.4.3 Stitching thread. The sewing thread shall be a good match to the basic material and shall conform to A-A-55094, type III, 3 ply, ticket number A, for all seaming and safety stitching. 3.4.4 Slide fastener (iack

27、et liner) The slide fastener for the front opening shall be separating, nonreversible, automatic, size light medium special with a short tab pull and single slider arrangement conforming to Type IV, style 6 of A-A-55634. The components shall be dark oxidized or natural brass. The length for all jack

28、et sizes shall be 20 inches with a minimum tape extension of 1-1/4 inches on the top end. 3.4.5 Snap fasteners. The snap fasteners for the jacket and trouser liner shall conform to style 2A, finish 2, of MIL-F-10884. The color of the exposed surface of the cap shall match the color 4 Provided by IHS

29、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27546E of the outershell material or shall be black. The placement of the snaps shall be as indicated on the pattern. 3.4.5.1 Jacket Liner Front opening. The top snap shall be placed 1/2 inch down from the col

30、lar and the last snap 1 inch above the finished bottom hem with the remaining snaps evenly spaced in between according to the marks on the pattern. 3.4.5.2 Jacket liner and trouser liner. Two female portion snaps shall be located on each inseam to be used to attach the liners together. The first sna

31、p shall be 1-1/2 inches upward from the finished bottom hem. The second shall be 1-1/2 inches upward from the first snap fastener and in vertical alignment. One corresponding male portion of the snap shall be located on each trouser outseam approximately 3 inches e 1/4 inch) from the top edge of the

32、 trouser. 3.4.6 Elastic webbing (trouser liner) The 1-3/4 inch wide elastic webbing shall have a thickness of .O48 inches minimum and a maximum weight of .95 oz. per linear yard when tested in accordance with paragraph 4.4. 3.5 Labels. Each liner shall have a combination identification/size label, a

33、nd a laundering label stitched on all sides approximately 1/2 to 1 inch below the collar seam on the jacket liner and stitched on all sides below the lower row of waistband stitching on the inside back above the right patch hip pocket on the trouser liner. The inscription shall have a minimum font s

34、ize of 10. The inscription legibility, label, and label attachment shall last the expected life of the coveralls. 3.5.1 Identification/size label The identification/size label shall contain the following information: Liner, flyers CW 9/P (jacket or trousers) Contract number Textile Fiber Products Ac

35、t Information Contractors name Size Stock number 3.5.2 Laundering instruction label The laundering instruction label shall contain the following information: 1. Machine washing Use Permanent Press Cycle. Wash in warm water with mild detergent. 2. Hand washing. Wash in warm water using mild detergent

36、. DO NOT WRING OR TWIST. Rinse in clean warm water. 3. DO NOT USE CHLORINE BLEACH OR STARCH. 4. Dry at low heat (do not exceed 130 F). After drying, tumble at room temperature for 10 minutes. Remove immediatelyfrom dryer. To drip dry, remove from water and place on rust-proof hanger. 5 Provided by I

37、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27546E DO NOT REMOVE THIS LABEL 3.5.3 Garment instruction 1abel.A paper instruction label measuring not less than 3-112 inches by 3-112 inches shall be included inside the sealed polyethylene bag with the ja

38、cket and trouser. The label shall contain the following information. The garment shall be unpacked and shaken out, at a room temperature of approximately 70 degrees Fahrenheit, before fitting to insure your correct size”. 3.5.4 Barcode tag. Each item shall be individually bar-coded, clearly legible

39、and readable by scanner. The bar-coding element shall be a 13 digit national stock number (NSN). The barcode type shall be medium to high code density, and shall be attached so that it is completely visible on the item when it is folded and lor packaged as specified. The label shall be attached with

40、out using adhesive or without piercing the fabric to prevent damage to the item. 3.5.5 Patterns. The government shall furnish a complete set of patterns or a master pattern with grade rules, to maintain uniformity and consistency in manufacturing. The government patterns shall be used to create the

41、contractors working patterns. Minor modifications are permitted to accommodate manufacturing procedures, however the design and finished measurements shall be maintained. TABLE II. List of pattern parts Jacket liner Cut pieces Right front 1 Left front 1 Back 1 Left sleeve 2 Pocket 1 Right sleeve 2 T

42、rouser liner Cut pieces Front 2 Back 2 Trouser pocket 2 3.6 Finished measurements The finished liners shall conform to measurements as shown in Table III and IV. TABLE III. Jacket Liner finished measurements (inches) Small Medium Large X-Large Tolerance Back length 11 26 26-112 26-112 27 + 1 -314 11

43、2 Chest circ. 21 22 24 26 28 + 112 -318 TABLE III. Jacket Liner finished measurements (continued) Small Medium Large X-Large Tolerance 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27546E Sleeve outseam 31 35 35-112 36-114 37 + 1 -314 112

44、 Sleeve bottom 41 6 6-114 6-112 6-314 - + 114 circ. (top of knit) Sweep 51 19-112 21-112 24-112 25-112 +1/2, -318 1/ The measurement of the back length shall be taken, at the center of the back, from the undercollar seam to the bottom of the jacket. - 2/ The measurement of the chest shall be taken w

45、ith the liner buttoned, from folded edge to folded edge in line with the armhole. - 3/ The measurement of the sleeve outseam shall be taken at the center back at the collar seam, diagonally across the back, down the sleeve to the edge of the knit cuff. - 4/ The measurement of the sleeve bottom shall

46、 be taken across the top of the knit cuff, with the bottom stretched taut, using manual tension. - 5/ The measurement of the sweep shall be taken, at the bottom of the jacket liner, from the folded edge to folded edge of the jacket fully buttoned. TABLE IV. Trouser Liner finished measurements (inche

47、s) Small Medium Large X-Large Tolerance % Relaxed waist 11 12 14-112 17 19-112 + 112 -114 circ. Outseam 21 38-114 39-314 41-114 42-314 I314 Inseam 31 26-314 27-114 27-314 28-114 I 114 % Bottom circ. 41 6 6-112 7 7-112 + 114 1/ The measurement of the relaxed waist shall be taken with the fly front fa

48、stened in the largest position. Measure along the top edge of the waistband from folded edge to folded edge. - 21 The measurement of the outseam shall be taken from the top edge of the waistband down the outseam to the top of the knit anklet. - 31 The measurement of the inseam shall be taken from th

49、e crotch down the inseam to the top of the knit anklet. - 41 The measurement of the bottom shall be taken across the bottom of the leg at the top of the knit cuff, with the bottom stretched taut, using manual tension. 4. VERIFICATION 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27546E Material defects Outside-Any hole, cut, tear, mend, burn, smash, misweave, missing yarn, or weake