DLA MIL-DTL-21604 6 C-2009 SWITCH ASSEMBLIES FOR REMOTE OPERATED SWITCHES 10 AMPERE STYLES RJR AND RJRA [Use NAVY MIL-S-24187 E SUPP 1 NAVY MIL-S-24187 E NAVY MIL-S-24187 D SUPP 3 .pdf

《DLA MIL-DTL-21604 6 C-2009 SWITCH ASSEMBLIES FOR REMOTE OPERATED SWITCHES 10 AMPERE STYLES RJR AND RJRA [Use NAVY MIL-S-24187 E SUPP 1 NAVY MIL-S-24187 E NAVY MIL-S-24187 D SUPP 3 .pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-21604 6 C-2009 SWITCH ASSEMBLIES FOR REMOTE OPERATED SWITCHES 10 AMPERE STYLES RJR AND RJRA [Use NAVY MIL-S-24187 E SUPP 1 NAVY MIL-S-24187 E NAVY MIL-S-24187 D SUPP 3 .pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-DTL-21604/6C 27 March 2009 SUPERSEDING MIL-DTL-21604/6B 27 June 2003 DETAIL SPECIFICATION SHEET SWITCH, ASSEMBLIES FOR REMOTE OPERATED SWITCHES, 10 AMPERE, STYLES RJR AND RJRA INACTIVE FOR NEW DESIGN AFTER 30 MARCH 1992 FOR NEW DESIGN, USE MIL-S-24187This specification is approved for

2、 use by all Depart- ments and Agencies of the Department of Defense. The complete requirements for acquiring the switches described herein shall consist of this specification and the latest issue of MIL-DTL-21604. FIGURE 1. Styles RJR and RJRA switch. AMSC N/A FSC 5930 Provided by IHSNot for ResaleN

3、o reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/6C 2 Inch mm Inch mm .005 .016 .062 .141 .144 .145 .190 .213 .221 .245 .248 .250 0.13 0.41 1.57 3.58 3.66 3.68 4.83 5.41 5.61 6.22 6.30 6.35 .252 .31 .38 .44 1.28 1.81 2.22 2.30 2.81 3.25 6.0 6.35 7.87 9.65 11.18 32.51

4、 45.97 56.39 58.42 71.37 82.55 152.4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only and are based upon 1 inch = 25.4 mm. 3. Unless otherwise specified, tolerances are .016 (0.41 mm) for two-place decimals and 0.005 (0.13 mm)

5、for three-place decimals. FIGURE 1. Styles RJR and RJRA switch - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/6C 3 NOTE: Viewed from the handle end. FIGURE 2. Rotor contact configuration and handle positions. Provided by I

6、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/6C 4 NOTE: Viewed from handle end. FIGURE 2. Rotor contact configuration and handle positions - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

7、,-,-MIL-DTL-21604/6C 5 REQUIREMENTS: Dimensions and configuration: See figure 1, figure 2, and table I. Angle of throw: 45 degrees. Switching action: Detent. Electrical loads: AC current: 10 amperes. Voltage: 125 volts (at 60 - 400 Hz, 0.80 inductive power factor). Temperature rise: 30C maximum. Con

8、tact material: Rotor: Silver-overlay phosphor-bronze. Stator: Silver-overlay copper. Barriers: See figure 1. Terminal marking: See figure 1. Stop marking: See figure 1. Qualification samples: See table II. TABLE I. Type designation and switching characteristics. Type designation Dimensions 2/ Compon

9、ent Rotor designation Style No. of switch sections Total number of sections including control sections A .06 (1.57) B Approx. weight (ounces) Maximum Rotational torque (inch-pounds) S S S S S 1 2 3 4 2 RJR RJR RJR RJR RJRA 25 25 25 25 26 27 27 27 27 27 12.56(319.07) 12.56(319.07) 12.56(319.07) 12.56

10、(319.07) 12.56(319.07) 12.06(306.37) +0.14 (3.58) 12.06(306.37) +0.14 (3.58) 12.06(306.37) +0.14 (3.58) 12.06(306.37) +0.14 (3.58) 12.06(306.37) +0.14 (3.58) 66 66 66 66 66 33-40 39-46 34-41 43-50 39-46 1/ For rotor designation, see figure 2. 2/ Dimensions are in inches. Metric equivalents (to the n

11、earest 0.01 mm) are given for general information only and are based upon 1 inch = 25.4 mm. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/6C 6 . TABLE II. Qualification test sample. Sample switch Test number 1/ Sample switch Test numb

12、er S1JR25 S1JR25 S1JR25 S2JR25 S2JR25 S2JR25 S3JR25 1 2 3 4 1 2 3 S3JR25 S4JR25 S4JR25 S4JR25 S4JR25 S4JR25 S4JR25 4 1 2 3 4 5 6 1/ Test numbers in accordance with table II of MIL-DTL-21604. 2/ For group qualifications, see 4.5.1. The margins of this specification are marked with vertical lines to i

13、ndicate where modifications from this amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content i

14、rrespective of the marginal notations. Reference Documents: MIL-DTL-21604 Custodians: Preparing activity: Navy - SH DLA - CC DLA - CC (Project 5930-2009-009) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-