DLA MIL-DTL-21604 4 C-2009 SWITCH ROTARY MULTIPOLE AND SELECTOR 7 5 AMPERE STYLE JM.pdf
《DLA MIL-DTL-21604 4 C-2009 SWITCH ROTARY MULTIPOLE AND SELECTOR 7 5 AMPERE STYLE JM.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-21604 4 C-2009 SWITCH ROTARY MULTIPOLE AND SELECTOR 7 5 AMPERE STYLE JM.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、INCH-POUND MIL-DTL-21604/4C 27 March 2009 SUPERSEDING MIL-DTL-21604/4B 27 June 2003 DETAIL SPECIFICATION SHEET SWITCH, ROTARY, MULTIPOLE AND SELECTOR, 7.5 AMPERE, STYLE JM This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The complete requirements
2、 for acquiring the switches described herein shall consist of this specification and the latest issue of MIL-DTL-21604. FIGURE 1. Style JM switch. AMSC N/A FSC 5930 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/4C 2 FIGURE 1. Style JM
3、 switch - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/4C 3 FIGURE 1. Style JM switch - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/4C 4 FIGURE
4、 1. Style JM switch - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21604/4C 5 Inch mm Inch mm Inch mm .005 .030 .033 .062 .155 0.13 0.76 0.84 1.57 3.94 .188 .210 .248 .281 .378 .39 4.78 5.33 6.30 7.14 9.60 9.9 1.810 1.815 6.00 1
5、5.88 45.97 46.10 152.4 .01 .016 .03 .05 .06 .08 .09 .109 .125 .141 .145 .147 .149 .150 .151 .153 0.3 0.41 0.8 1.3 1.5 2.0 2.3 2.77 3.18 3.58 3.68 3.73 3.78 3.81 3.84 3.89 .162 .165 .172 .19 .190 .22 .221 .25 250 .252 .256 .258 .31 .34 .375 4.11 4.19 4.37 4.8 4.83 5.6 5.61 6.3 6.35 6.40 6.50 6.55 7.9
6、 8.6 9.52 .41 .44 .50 .625.75 .97 1.00 1.28 1.69 1.81 2.22 2.30 2.81 3.00 3.25 3.75 4.50 +10.4 11.2 12.7 19.1 24.6 25.4 32.5 42.9 46.0 56.4 58.4 71.4 76.2 82.5 95.3 114.3 NOTE : S. to the nearest 0.01 mm) are given for general information only and are based upon tolerances are .016 (0.41 mm) for two
7、-place decimals and 0.005 (0.13 mm) . facilitate attachment to rear supports. A hex nut and lockwasher shall be 5. Dial marking, when required, shall be as specified in MIL-DTL-21604 (see 6.2). FIGURE 1. Style JM switch1. Dimensions are in inches. 2 Metric equivalents (1 inch = 25.4 mm. 3. Unless ot
8、herwise specified, for three-place decimals. 4 On switches of 20 sections or more, the securing rods shall extend .50 inch (12.70 mm) beyond the hex nuts at the rear of the switches toprovided for each rod extension. - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted w
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL216044C2009SWITCHROTARYMULTIPOLEANDSELECTOR75AMPERESTYLEJMPDF

链接地址:http://www.mydoc123.com/p-690089.html