DLA MIL-DTL-21097 15 G-2005 CONNECTORS ELECTRICAL PRINTED WIRING BOARD MALE ADAPTER CONTACT SPACING 0 200 ALTERNATE DUAL ROW TYPE CS BLADE CONTACT (NO MOUNTING PROVISION)《刀口式触点CS型交.pdf

《DLA MIL-DTL-21097 15 G-2005 CONNECTORS ELECTRICAL PRINTED WIRING BOARD MALE ADAPTER CONTACT SPACING 0 200 ALTERNATE DUAL ROW TYPE CS BLADE CONTACT (NO MOUNTING PROVISION)《刀口式触点CS型交.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-21097 15 G-2005 CONNECTORS ELECTRICAL PRINTED WIRING BOARD MALE ADAPTER CONTACT SPACING 0 200 ALTERNATE DUAL ROW TYPE CS BLADE CONTACT (NO MOUNTING PROVISION)《刀口式触点CS型交.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMIL-DTL-21097/15G 18 August 2005 SUPERSEDING MIL-C-21097/15F 15 February 1989 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, PRINTED WIRING BOARD MALE ADAPTER, CONTACT SPACING: 0.200, ALTERNATE DUAL ROW, TYPE CS, BLADE CONTACT (NO MOUNTING PROVISION) This specification is approved for

2、use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-21097. FIGURE 1. Blade contact type CS alternate dual row contacts. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo re

3、production or networking permitted without license from IHS-,-,-MIL-DTL-21097/15G 2Inches mm Inches mm .001 0.03 .155 3.94 .010 0.25 .160 4.06 .015 0.38 .200 5.08 .0245 0.622 .230 5.84 .082 2.08 .280 7.11 .100 2.54 .400 10.16 .106 2.69 .415 10.54 .125 3.18 .460 11.68 .150 3.81 NOTES: 1. Dimensions a

4、re in inches. 2. Unless otherwise specified, tolerance is .005 (.13 mm) for three place decimals. 3. Metric equivalents are given for information only. 4. See table I for dimensions. 5. All even numbered contacts to be identified with .047 (1.19 mm) minimum high characters, as shown. FIGURE 1. Blade

5、 contact type CS alternate dual row contacts - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21097/15G 3Printed wiring board Size T dim 2 3 4 .062 (1.57) .093 (2.36) .125 (3.18) Inches mm .002 0.05 .050 1.27 .052 1.32 .093 2.36 .

6、100 2.54 .200 5.08 .300 7.62 .350 8.89 .625 15.88 .895 22.73 4.731 120.17 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .005 (.13 mm) for three-place decimals. 3. Metric equivalents are given for information only. 4. See table II for dimensions B and C. FIGURE 2. Pr

7、inted wiring test board. -,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSMIL-DTL-21097/15G 4REQUIREMENTS Dimensions and configuration: See figure 1 and table I. Contact material: Gilding metal brass in accordance with copper alloy UNS C21000 of ASTM

8、B36. Mating receptacle: Shall be in accordance with MIL-DTL-21097/13. Printed wiring test board: Two-ounce copper one side only, gold plated in accordance with IPC-D-275. Board in accordance with IPC-D-275. See figure 2 for the applicable connector size. Finish: See MIL-DTL-21097. Part or Identifyin

9、g Number (PIN): M21097/15-(dash number from table I). TABLE I. Connector, electrical, male adapter, type CS, class b, no mounting provision. Dimensions (inches) 1/Dash number Style Size A (maximum) B C .010 (0.25) 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 17 17 17 23 23 23 29 29 29 35 35 35 41 41

10、 41 2 3 4 2 3 4 2 3 4 2 3 4 2 3 4 2.070 (52.58) 2.670 (67.82) 3.270 (83.06) 3.870 (98.30) 4.470 (113.54) 1.600 (40.64) 2.200 (55.88) 2.800 (71.12) 3.400 (86.36) 4.000 (101.60) 0.120 (3.05) 0.152 (3.86) 0.183 (4.65) 0.120 (3.05) 0.152 (3.86) 0.183 (4.65) 0.120 (3.05) 0.152 (3.86) 0.183 (4.65) 0.120 (

11、3.05) 0.152 (3.86) 0.183 (4.65) 0.120 (3.05) 0.152 (3.86) 0.183 (4.65) See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21097/15G 5TABLE I. Connector, electrical, male adapter, type CS, class b, no mounting provis

12、ion Continued. Dimensions (inches) 1/Dash number Style Size A (maximum) B C 0.010 (0.25) 16 17 18 47 47 47 2 3 4 5.070 (128.78) 4.600 (116.84) 0.120 (3.05) 0.152 (3.86) 0.183 (4.65) 1/ Dimensions are in inches. Metric equivalents are given for information only. TABLE II. Printed wiring test board. D

13、imensions (inches) 1/Style B C 17 3.390 (86.10) 1.600 (40.64) 23 3.990 (101.34) 2.200 (55.88) 29 4.590 (116.58) 2.800 (71.12) 35 5.190 (131.82) 3.400 (86.36) 41 5.790 (147.06) 4.000 (101.60) 47 6.390 (162.23) 4.600 (116.84) 1/ Millimeters are in parentheses. Changes from previous issue. Marginal not

14、ations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-21097, this document references the following: MIL-DTL-21097/13 ASTM B36 IPC-D-275 Provided by IHSNot for ResaleNo reproduction o

15、r networking permitted without license from IHS-,-,-MIL-DTL-21097/15G 6CONCLUDING MATERIALS Custodians: Preparing activity: Army CR DLA - CC Navy EC Air Force 11 (Project 5935-4505-006) DLA - CC Review activities: Army AR, AT, AV, CR4, MI Navy AS, MC, OS, SH NOTE: The activities listed above were in

16、terested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-