DLA MIL-DTL-15098 E-2010 LAMPS GLOW GENERAL SPECIFICATION FOR.pdf

《DLA MIL-DTL-15098 E-2010 LAMPS GLOW GENERAL SPECIFICATION FOR.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-15098 E-2010 LAMPS GLOW GENERAL SPECIFICATION FOR.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Comments, suggestions, or questions on this document should be addressed to Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616, or e-mailed to STDZNMGTdla.mil. Since contact information can change, you may want to verify the currency of this address informat

2、ion using the ASSIST database at https:/assist.daps.dla.mil/. AMSC N/A FSC 6240 INCH-POUND MIL-DTL-15098E 23 August 2010 SUPERSEDING MIL-L-15098D 14 December 1973 DETAIL SPECIFICATION LAMPS, GLOW, GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and Agencies of the

3、 Department of Defense. 1. SCOPE 1.1 Scope. This specification covers hermetically sealed glow lamps containing gases or vapor in which luminosity is produced by ionization of these gases for indicating and circuit control functions. The region of high luminosity is near the negative electrode (or c

4、athode). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effo

5、rt has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of the documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications and standards. The fo

6、llowing specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

7、-,-MIL-DTL-15098E 2 DEPARTMENT OF DEFENSE SPECIFICATIONS (See supplement 1 for list of specification sheets.) DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Method Standard Electronic and Electrical Component Parts MIL-STD-1285 - Marking of Electrical and Electronic Parts (Copies of these docume

8、nts are available online at https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-government publications. The following document forms a part of this document to the extent specified herein. Unless otherwi

9、se specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR QUALITY (ASQ) ASQ Z1.4 - Sampling Procedures and Tables for Inspection by Attributes (Copies of this document are available online at http:/www.asq.org/ or from American Society of Quali

10、ty, 600 North Plankinton Avenue, Milwaukee, WI 53203.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes pr

11、ecedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual item requirements shall be as specified herein and in accordance with the applicable specification sheets. I

12、n the event of any conflict between the requirements of this specification and the specification sheet, the latter shall govern. 3.2 First article. When specified (see 6.2), the contractor shall furnish sample units for first article inspection and approval (see 4.3). 3.3 General characteristics. Th

13、e general characteristics of glow lamps shall be such that once a discharge has commenced, the voltage drop across the electrodes remains essentially constant throughout an appreciable change in current flow. This entails the insertion of a current limiting resistor (see 3.4), so calculated that cur

14、rent cannot exceed a predetermined value. No post-delivery aging or conditioning shall be required to achieve the stability and reliability needed to meet the applicable performance requirements stated herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

15、IHS-,-,-MIL-DTL-15098E 3 3.4 Resistors. Unless otherwise specified (see 3.1), the current limiting resistors shall be located externally. Unless otherwise specified (see 6.2), external resistors shall not be furnished with the lamps. 3.5 Bulb shape, size, and finish. 3.5.1 Bulb shape. The bulb shape

16、 shall be as specified (see 3.1) and shall be designated by letters as follows: G - Globular S - Straight side T - Tubular 3.5.2 Bulb size. The bulb size shall be expressed by a number denoting the greatest diameter in eighths of an inch. Example: a bulb size of 4-1/2 would indicate a diameter of 9/

17、16 inch (4-1/2 x 1/8 = 9/2 x 1/8 = 9/16). 3.5.3 Bulb finish. Bulb finish for glow lamps shall be clear (colorless). 3.6 Lamp bases. Lamp bases shall be as specified (see 3.1) and shall be identified by the following symbols: M - Medium screw CS - Candelabra screw DCB - Double contact bayonet candela

18、bra DCBS - Double contact bayonet skirted MB - Single contact miniature bayonet SMF - Single contact midget flange NB - Unbased wire leads treated to meet solderability requirements 3.7 Electrode shapes. Electrode shapes shall be as specified (see 3.1) and shall be identified by the following symbol

19、s: P2 - Split disk P3 - Split hemispherical plates P4 - Parallel disks PW5 - Cylinder and helical electrode PW27 - Wire ring, flat plate W11 - Parallel posts 3.8 Solderability of wire terminals. When tested in accordance with 4.6.2, the dipped surfaces of the type NB unbased wire leads shall be at l

20、east 95 percent covered with a new, smooth, solder coating. The remaining 5 percent of the lead surface shall show only small pinholes or rough spots, and these deficiencies shall not be concentrated in one area. Bare base metal and areas where the solder dip failed to cover the original coating are

21、 indications of poor solderability, and shall be cause for rejection. In case of dispute, the percent of coverage with Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15098E 4 pinholes or rough spots shall be determined by actual measurement

22、of these areas as compared to the total area. 3.9 Starting voltage. When tested in accordance with 4.6.3, the starting voltage shall be as specified (see 3.1). 3.10 Maintaining voltage. When tested in accordance with 4.6.4, the maintaining voltage shall be as specified (see 3.1). 3.11 Extinguishing

23、voltage. When tested in accordance with 4.6.5, the extinguishing voltage shall be as specified (see 3.1). 3.12 Initial light output. When tested in accordance with 4.6.6, the initial light output shall be not less than specified (see 3.1). 3.13 Leakage resistance. When tested in accordance with 4.6.

24、7, the leakage resistance shall be not less than 100 megohms, unless otherwise specified (see 3.1). 3.14 Vibration. When tested in accordance with 4.6.8, lamps shall remain electrically and mechanically operative (see 3.1). 3.15 Shock. When tested in accordance with 4.6.9, lamps shall remain electri

25、cally and mechanically operative (see 3.1). 3.16 Life. When tested in accordance with 4.6.10, the average useful lamp life shall be as specified (see 3.1 and 6.4). 3.17 Electrode glow. When tested in accordance with 4.6.11, the indicator lamps with W11 electrode shapes (see 3.1) shall produce corona

26、 coverage as specified. The absence of corona between the electrodes is permissible. 3.18 Marking. Lamps shall be marked in accordance with the requirements of MIL-STD-1285 with the industry type number (ANSI) and the manufacturers source code (CAGE). Where physical size precludes the printing of re

27、quired data on the lamp itself, each unit package, exterior container, and unitized load shall be marked with the required information in addition to the corresponding military part number as identified in the cross-reference table (see 6.8). In addition, lamps containing radioactive materials shall

28、 be marked as specified in 3.18.1. 3.18.1 Radioactive marking. Lamps with intentionally added radioactive isotopes with a measured radioactivity level less than or equal to 0.002 microcuries per gram shall be considered non-radioactive for purposes of marking. Lamps with intentionally added radioact

29、ive isotopes with an emission level below 0.5 millirems per hour shall be marked in accordance with International Atomic Energy Agency (IAEA) marking requirements for category I radionuclides. Where size precludes, radioactive marking information shall be placed on the unit package. Provided by IHSN

30、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15098E 5 3.19 Workmanship. Lamp shall be processed in such a manner as to be uniform in quality and shall be free of cracks, chips, sharp edges, and burrs on metal parts. Soldering welding, brazing, cementing,

31、and wiring shall be thorough. Alignment of parts shall be accurate. 3.20 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operation

32、al and maintenance requirements, and promotes economically advantageous life cycle costs. 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.3). b. Conformance inspection (see 4.4). 4.2 Inspect

33、ion conditions. Unless otherwise specified herein, all inspections shall be performed in accordance with the test conditions specified in the general requirements of MIL-STD-202. 4.3 First article inspection. First article inspection shall be performed by the supplier, after award of contract and pr

34、ior to production, at a location acceptable to the Government. First article inspection shall be performed on sample units which have been produced with equipment and procedures normally used in production. First article approval is valid only on the contract or purchase order under which it is gran

35、ted, unless extended by the Government to other contracts or purchase orders. Examination and tests shall be as specified in 4.3.1. 4.3.1 Samples for first article inspection. Twenty lamps, of each type, shall be subjected to the examination and tests specified in table I in the order shown. TABLE I

36、. First article inspection. Examination or test Requirement paragraph Examination or test paragraph Number of sample units to be inspected Visual and dimensional 3.4 to 3.7, 3.18, 3.19 4.6.1 All Solderability 3.8 4.6.2 All Starting voltage in light 3.9 4.6.3 1 - 10 Starting voltage in total darkness

37、 3.9 4.6.3 11 - 20 Maintaining voltage 1 3.10 4.6.4 All Extinguishing voltage 1 3.11 4.6.5 1 - 10 Initial light output 23.12 4.6.6 1 - 10 Leakage resistance 13.13 4.6.7 11 - 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15098E 6 TABLE I.

38、 First article inspection - Continued. Examination or test Requirement paragraph Examination or test paragraph Number of sample units to be inspected Vibration 3.14 4.6.8 All Shock 3.15 4.6.9 Life 3.16 4.6.10 All Electrode glow 23.17 4.6.11 All 1 Applicable only to circuit control lamps. 2 Applicabl

39、e only to indicator lamps, when specified (see 3.1). 4.3.2 Failures. One or more failures shall be cause for refusal to grant first article approval. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection (see 4.4.

40、1.2). 4.4.1.1 Inspection lot. An inspection lot shall consist of all lamps covered by a single part number, produced under essentially the same conditions, and offered for inspection at one time. 4.4.1.2 Group A inspection. Sample lamps shall be selected from each lot in accordance with ASQ Z1.4, in

41、spection level II, with the Acceptance Quality Limit (AQL) as specified in the contract (see 6.2) for the examination and tests specified in table II and shall be conducted in the order listed. TABLE II. Group A inspection. Examination or test Requirement paragraph Examination or test paragraph Visu

42、al and dimensional 3.4 to 3.7, 3.18, and 3.19 4.6.1 Solderability 3.8 4.6.2 Starting voltage in light 3.9 4.6.3 Maintaining voltage 13.10 4.6.4 Leakage resistance 13.13 4.6.7 Electrode glow 23.17 4.6.11 1Applicable only to circuit control lamps. 2Applicable only to indicator lamps with W11 electrode

43、s. 4.4.1.3 Group B tests. Twenty sample lamps shall be selected from the first lot and periodically thereafter, if required under 6.2, and shall be subjected to the tests specified in table III in the order listed. Samples selected shall have passed the group A inspection specified in 4.4.1.2. If on

44、e or more samples fail to pass the group B tests, the lot shall be subject to rejection. Sample units which have been subjected to the group B tests shall not be offered for delivery. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15098E 7 T

45、ABLE III. Group B tests. Test Requirement paragraph Test paragraph Starting voltage in total darkness 3.9 4.6.3 Extinguishing voltage 13.11 4.6.5 Initial light output 23.12 4.6.6 Vibration 3.14 4.6.8 Shock 3.15 4.6.9 Life 3.16 4.6.10 1Applicable only to circuit control lamps. 2Applicable only to ind

46、icator lamps, when specified (see 3.1). 4.5 Test conditions. 4.5.1 Electrostatic and electromagnetic fields. The test area shall be relatively free of electrostatic and radio frequency electromagnetic fields so as not to affect the firing potential of the lamps. 4.5.2 Couplings and shields. Capaciti

47、ve couplings and electromagnetic shields, including portions of the body, metal plates, dark enclosures, photometer spheres and electrical conductors, other than those connected to the lamp under test, shall be kept at least 6 inches from the lamp being tested for starting, maintaining and extinguis

48、hing voltages. 4.5.3 Alternating current (AC) test voltage and frequency. The AC test voltage shall be a 60 Hertz (Hz) sine wave having a harmonic content of not more than 3 percent root mean square (rms) of the fundamental. Life test AC voltage shall be 120 3.6 volts AC and shall have a maximum cre

49、st factor of 1.45. 4.5.4 Direct current (DC) test voltage. Unless otherwise specified (see 3.1), DC life test voltage shall be 120 1.2 volts. DC test voltage shall be of sufficient magnitude for the lamp under test and shall have a ripple of less than 0.1 percent, except that for life testing, the ripple shall be less than 1.0 percent. 4.5.5 Measurement in light. Measurement in light shall be made in an unobstructed