DLA MIL-C-5 18 F-2013 CAPACITORS FIXED MICA DIELECTRIC STYLES CM04 CM05 CM06 CM07 CM08 CM09 CM10 CM11 CM12 AND CM13 [Use ARMY MIL-PRF-39001 5 E ARMY MIL-PRF-39001 5 D VALID NOTICE .pdf

《DLA MIL-C-5 18 F-2013 CAPACITORS FIXED MICA DIELECTRIC STYLES CM04 CM05 CM06 CM07 CM08 CM09 CM10 CM11 CM12 AND CM13 [Use ARMY MIL-PRF-39001 5 E ARMY MIL-PRF-39001 5 D VALID NOTICE .pdf》由会员分享，可在线阅读，更多相关《DLA MIL-C-5 18 F-2013 CAPACITORS FIXED MICA DIELECTRIC STYLES CM04 CM05 CM06 CM07 CM08 CM09 CM10 CM11 CM12 AND CM13 [Use ARMY MIL-PRF-39001 5 E ARMY MIL-PRF-39001 5 D VALID NOTICE .pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5910 INCH-POUND MIL-C-5/18F 29 March 2013 SUPERSEDING MIL-C-5/18E 18 June 2001 MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, MICA DIELECTRIC, STYLES CM04, CM05 CM06, CM07, CM08, CM09, CM10, CM11, CM12, AND CM13 INACTIVE FOR NEW DESIGN AFTER 21 DECEMBER 1970. USE MIL-PRF-39001/5. This

2、 specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the capacitors described herein shall consist of this specification sheet and MIL-C-5. STRAIGHT LEAD CRIMPED LEAD Styles CM04, CM05, Styles CM09, CM10 CM06, CM07, 200

3、 percent of rated dc voltage for not less than 1 second nor more than 5 seconds. Barometric pressure, qualification only: Method 105 of MIL-STD-202, test condition D; 100,000 feet. Test potential, 100 percent of rated dc voltage for 500 volt styles CM04 and CM09; 150 percent for lesser voltage ratin

4、gs and all other styles. Insulation resistance: Method 302 of MIL-STD-202, test condition A. 1/ Product obtained by multiplying the capacitance in microfarads by the insulation resistance in megohms. Dissipation factor: See MIL-C-5. Capacitance: Method 305 of MIL-STD-202. Vibration: Method 204 of MI

5、L-STD-202, test condition D. Symbol Capacitance tolerance D .5 pF F 1% G 2% J 5% Symbol Temperature range O -55C to +125C P -55C to +150C Symbol Temperature coefficient (ppm/C) Capacitance drift Capacitance values C -200 to +200 (0.5 percent + 0.1 pF) 1 pF thru 18 pF E -20 to +100 (0.1 percent + 0.1

6、 pF) 20 pF thru 82 pF F 0 to +70 (0.05 percent + 0.1 pF) 91 pF and greater Capacitance rating Minimum insulation resistance At +25C 0 to 10,000 pF 100,000 megohms 10,000 pF and greater 1,000 megohm-microfarads 1/ At +125C 0 to 3,300 pF 10,000 megohms minimum 3,300 pF and greater 33 megohm-microfarad

7、s 1/ At +150C 0 to 1,500 pF 5,000 megohms 1,500 pF and greater 7.5 megohm-microfarads 1/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-5/18F 5 Thermal shock: Method 107 of MIL-STD-202, condition A, except the high temperature shall be as foll

8、ows: Symbol O: +125C. Symbol P: +150C. Immersion: Method 104 of MIL-STD-202, test condition B. Dielectric withstanding voltage: Meet initial requirement. Insulation resistance: At least 30 percent of initial requirement. Dissipation factor: Not greater than 150 percent of initial requirement. Capaci

9、tance change: Shall not exceed 1 percent of nominal value of 1 pF, whichever is greater. Shock (specified pulse): Method 213 of MIL-STD-202, test condition I (100G). Solderability: Method 208 of MIL-STD-202. Terminal strength: Pull test: Capacitor held by one terminal and a 5 pound load gradually ap

10、plied to other terminal and maintained for at least 5 seconds. Twist test (straight wire leads only): 5 alternate 360 rotations. Bend test (crimped wire leads only): 90 two directions from vertical. Moisture resistance: Method 106 of MIL-STD-202: Dielectric withstanding voltage: Initial requirement.

11、 Insulation resistance: At least 30 percent of initial requirement. Dissipation factor: Not greater than 150 percent of initial requirement. Capacitance change: Shall not exceed 1 percent of nominal value of 1 pF, whichever is greater. Temperature coefficient and capacitance drift: Within the limits

12、 specified for the applicable characteristic. Low temperature storage and life: 48 hours at -55 +0C, -2C immediately followed by qualification or performance test, as applicable. Qualification test: 2,000 hours at applicable high test temperature with 150 percent of rated dc voltage applied. Dielect

13、ric withstanding voltage: Initial requirement. Insulation resistance: Initial requirement. Dissipation factor: Not greater than 150 percent of initial requirement. Capacitance change: Shall not exceed 1 percent of nominal value or 1 pF, whichever is greater. Performance check: Conditions and require

14、ments in accordance with qualification test except that test duration shall be 250 hours. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-5/18F 6 Continuation test: Units that have been subjected to the 250 hour test shall be continued for an a

15、dditional 1,750 hours and meet the requirements for the qualification test. Qualification inspection: Qualification inspection (Group A) is required. TABLE II. Type designations. Styles CM04 and CM09 Type designation 1/ Capacitance value (pF) DC rated voltage (volts) Operating temperature range Capa

16、citance tolerances CM-CD010D-3 1 500 O,P D CM-CD050D-3 5 500 O,P D CM-CD060D-3 6 500 O,P D CM-CD070D-3 7 500 O,P D CM-CD080D-3 8 500 O,P D CM-CD100D-3 10 500 O,P D CM-CD120J-3 12 500 O,P J CM-CD150J-3 15 500 O,P J CM-CD180J-3 18 500 O,P J CM-ED200J-3 20 500 O,P J CM-ED220J-3 22 500 O,P J CM-ED240J-3

17、 24 500 O,P J CM-ED270-3 27 500 O,P G,J CM-ED300-3 30 500 O,P G,J CM-ED330-3 33 500 O,P G,J CM-ED360-3 36 500 O,P G,J CM-ED390-3 39 500 O,P G,J CM-ED430-3 43 500 O,P G,J CM-ED470-3 47 500 O,P G,J CM-ED510-3 51 500 O,P F,G,J CM-ED560-3 56 500 O,P F,G,J CM-ED620-3 62 500 O,P F,G,J CM-ED680-3 68 500 O,

18、P F,G,J CM-ED750-3 75 500 O,P F,G,J CM-ED820-3 82 500 O,P F,G,J CM-FD910-3 91 500 O,P F,G,J CM-FD101-3 100 500 O,P F,G,J CM-FD111-3 110 500 O,P F,G,J CM-FD121-3 120 500 O,P F,G,J CM-FD131-3 130 500 O,P F,G,J CM-FD151-3 150 500 O,P F,G,J CM-FD161-3 160 500 O,P F,G,J CM-FD181-3 180 500 O,P F,G,J CM-FD

19、201-3 200 500 O,P F,G,J CM-FD221-3 220 500 O,P F,G,J CM-FD241-3 240 500 O,P F,G,J CM-FC271-3 270 300 O,P F,G,J CM-FC301-3 300 300 O,P F,G,J CM-FA331-3 330 100 O,P F,G,J CM-FA361-3 360 100 O,P F,G,J CM-FA391-3 390 100 O,P F,G,J See footnote at end of table. Provided by IHSNot for ResaleNo reproductio

20、n or networking permitted without license from IHS-,-,-MIL-C-5/18F 7 TABLE II. Type designations - Continued. Styles CM05 and CM10 Type designation 1/ Capacitance value (pF) DC rated voltage (volts) Operating temperature range Capacitance tolerances CM-CD010D-3 1 500 O,P D CM-CD050D-3 5 500 O,P D CM

21、-CD060D-3 6 500 O,P D CM-CD070D-3 7 500 O,P D CM-CD080D-3 8 500 O,P D CM-CD100D-3 10 500 O,P D CM-CD120J-3 12 500 O,P J CM-CD150J-3 15 500 O,P J CM-CD180J-3 18 500 O,P J CM-ED200J-3 20 500 O,P J CM-ED220J-3 22 500 O,P J CM-ED240J-3 24 500 O,P J CM-ED270-3 27 500 O,P G,J CM-ED300-3 30 500 O,P G,J CM-

22、ED330-3 33 500 O,P G,J CM-ED360-3 36 500 O,P G,J CM-ED390-3 39 500 O,P G,J CM-ED430-3 43 500 O,P G,J CM-ED470-3 47 500 O,P G,J CM-ED510-3 51 500 O,P F,G,J CM-ED560-3 56 500 O,P F,G,J CM-ED620-3 62 500 O,P F,G,J CM-ED680-3 68 500 O,P F,G,J CM-ED750-3 75 500 O,P F,G,J CM-ED820-3 82 500 O,P F,G,J CM-FD

23、910-3 91 500 O,P F,G,J CM-FD101-3 100 500 O,P F,G,J CM-FD111-3 110 500 O,P F,G,J CM-FD121-3 120 500 O,P F,G,J CM-FD131-3 130 500 O,P F,G,J CM-FD151-3 150 500 O,P F,G,J CM-FD161-3 160 500 O,P F,G,J CM-FD181-3 180 500 O,P F,G,J CM-FD201-3 200 500 O,P F,G,J CM-FD221-3 220 500 O,P F,G,J CM-FD241-3 240 5

24、00 O,P F,G,J CM-FD271-3 270 500 O,P F,G,J CM-FD301-3 300 500 O,P F,G,J CM-FD331-3 330 500 O,P F,G,J CM-FD361-3 360 500 O,P F,G,J CM-FD391-3 390 500 O,P F,G,J See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-5/18F 8

25、TABLE II. Type designations - Continued. Styles CM06 and CM11 Type designation 1/ Capacitance value (pF) DC rated voltage (volts) Operating temperature range Capacitance tolerances CM-FD431-3 430 500 O,P F,G,J CM-FD471-3 470 500 O,P F,G,J CM-FD511-3 510 500 O,P F,G,J CM-FD561-3 560 500 O,P F,G,J CM-

26、FD621-3 620 500 O,P F,G,J CM-FD681-3 680 500 O,P F,G,J CM-FD751-3 750 500 O,P F,G,J CM-FD821-3 820 500 O,P F,G,J CM-FD911-3 910 500 O,P F,G,J CM-FD102-3 1,000 500 O,P F,G,J CM-FD112-3 1,100 500 O,P F,G,J CM-FD122-3 1,200 500 O,P F,G,J CM-FD132-3 1,300 500 O,P F,G,J CM-FD152-3 1,500 500 O,P F,G,J CM-

27、FD162-3 1,600 500 O,P F,G,J CM-FD182-3 1,800 500 O,P F,G,J CM-FD202-3 2,000 500 O,P F,G,J CM-FD222-3 2,200 500 O,P F,G,J CM-FD242-3 2,400 500 O,P F,G,J CM-FD272-3 2,700 500 O,P F,G,J CM-FD302-3 3,000 500 O,P F,G,J CM-FD332-3 3,300 500 O,P F,G,J CM-FD362-3 3,600 500 O,P F,G,J CM-FD392-3 3,900 500 O,P

28、 F,G,J CM-FD432-3 4,300 500 O,P F,G,J CM-FD472-3 4,700 500 O,P F,G,J CM07 and CM12 CM-FD512-3 5,100 500 O,P F,G,J CM-FD562-3 5,600 500 O,P F,G,J CM-FD622-3 6,200 500 O,P F,G,J CM-FD682-3 6,800 500 O,P F,G,J CM-FD752-3 7,500 500 O,P F,G,J CM-FD822-3 8,200 500 O,P F,G,J CM-FD912-3 9,100 500 O,P F,G,J

29、CM-FD103-3 10,000 500 O,P F,G,J CM-FD113-3 11,000 500 O,P F,G,J CM-FD123-3 12,000 500 O,P F,G,J CM-FD133-3 13,000 500 O,P F,G,J CM-FD153-3 15,000 500 O,P F,G,J CM-FD163-3 16,000 500 O,P F,G,J CM-FD183-3 18,000 500 O,P F,G,J CM-FD203-3 20,000 500 O,P F,G,J See footnote at end of table. Provided by IH

30、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-5/18F 9 TABLE II. Type designations - Continued. Styles CM08 and CM13 Type designation 1/ Capacitance value (pF) DC rated voltage (volts) Operating temperature range Capacitance tolerances CM-FD223-3 22,000 500

31、 O,P F,G,J CM-FD243-3 24,000 500 O,P F,G,J CM-FD273-3 27,000 500 O,P F,G,J CM-FD303-3 30,000 500 O,P F,G,J CM-FD333-3 33,000 500 O,P F,G,J CM-FD363-3 36,000 500 O,P F,G,J CM-FD393-3 39,000 500 O,P F,G,J CM-FD433-3 43,000 500 O,P F,G,J CM-FD473-3 47,000 500 O,P F,G,J CM-FD513-3 51,000 500 O,P F,G,J C

32、M-FC563-3 56,000 300 O,P F,G,J CM-FC623-3 62,000 300 O,P F,G,J CM-FC683-3 68,000 300 O,P F,G,J CM-FA753-3 75,000 100 O,P F,G,J CM-FA823-3 82,000 100 O,P F,G,J CM-FA913-3 91,000 100 O,P F,G,J 1/ Complete type designation, where applicable, will include additional letter symbols to indicate the style,

33、 capacitance tolerance, and operating temperature range. Referenced documents: In addition to MIL-C-5, this document references MIL-STD-202. Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This

34、 was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the l

35、ast previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5910-2013-006) DLA - CC Review activities: Navy - AS, CG, MC, OS, SH Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-