DLA DSCC-VID-V62 12665-2012 MICROCIRCUIT LINEAR 1 MHz TO 8 GHz 70 dB LOGARITHMIC DETECTOR CONTROLLER MONOLITHIC SILICON.pdf

《DLA DSCC-VID-V62 12665-2012 MICROCIRCUIT LINEAR 1 MHz TO 8 GHz 70 dB LOGARITHMIC DETECTOR CONTROLLER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-VID-V62 12665-2012 MICROCIRCUIT LINEAR 1 MHz TO 8 GHz 70 dB LOGARITHMIC DETECTOR CONTROLLER MONOLITHIC SILICON.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dl

2、a.mil/ Original date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA TITLE MICROCIRCUIT, LINEAR, 1 MHz TO 8 GHz, 70 dB LOGARITHMIC DETECTOR/CONTROLLER, MONOLITHIC SILICON 12-12-12 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/12665 REV PAGE 1 OF 17 AMSC N/A 5962-V012-13 Provi

3、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 1 MHz to 8GHz, 70 dB lo

4、garithmic detector/controller microcircuit, with an operating temperature range of -55C to +105C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item

5、on the engineering documentation: V62/12665 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 AD8318 1 MHz to 8GHz, 70 dB logarithmic detector/controller 1.2.2 Case outline(s). The case outli

6、ne(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 16 MO-220-WGGC Lead frame chip scale package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder

7、dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 3 1.3 Absolute maximum ratings. 1

8、/ Supply voltage : VPSO pin, VPSI pin . 5.7 V ENBL, VSETvoltage . 0 to VPOSInput power (single ended, reference 50 ) . 12 dBm Internal power dissipation (PD) 0.73 W Maximum junction temperature range (TJ) . 130C Storage temperature range (TSTG) -65C to +150C 1.4 Recommended operating conditions. 2/

9、Operating free-air temperature range (TA) . -55C to +105C 1.5 Thermal characteristics. Thermal resistance, junction to ambient (JA) 55C/W 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation

10、of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Use of this product beyond the manufacturers design rules or stated para

11、meters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE

12、IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC Solid State Technology Association JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington,

13、VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Uni

14、t container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herei

15、n. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure

16、 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/Temperature, TA Device type

17、 Limits Unit Min Max Signal input interface. INHI pin and INLO pin. Specified frequency range +25C 01 0.001 8 GHz DC common mode voltage VPOS 1.8 typical V Measurement mode. VOUTpin shorted to VSETpin, sinusoidal input signal. f = 900 MHz, RTADJ= 500 . Input impedance 3/ +25C 01 957|0.71 typical |pF

18、 3 dB dynamic range +25C 01 65 typical dB -55C to +105C 63 typical 1 dB dynamic range +25C 01 57 typical dB Maximum input level 1 dB error -55C to +105C 01 -1 typical dBm Minimum input level 1 dB error -55C to +105C 01 -58 typical dBm Slope -55C to +105C 01 -26 -23 mV/dB Intercept -55C to +105C 01 1

19、9.5 24 dBm Output voltage - high power in PIN= -10 dBm -55C to +105C 01 0.7 0.86 V Output voltage - low power in PIN= -40 dBm -55C to +105C 01 1.42 1.62 V Temperature sensitivity PIN= -10 dBm +25C to +105C 01 0.0071 typical dB/C -55C to +25C 0.0031 typical See footnotes at end of table. Provided by

20、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TA Device type Limit

21、s Unit Min Max Measurement mode. VOUTpin shorted to VSETpin, sinusoidal input signal. f = 1.9 GHz, RTADJ= 500 . Input impedance 3/ +25C 01 523|0.68 typical |pF 3 dB dynamic range +25C 01 65 typical dB -55C to +105C 63 typical 1 dB dynamic range +25C 01 57 typical dB Maximum input level 1 dB error -5

22、5C to +105C 01 -2 typical dBm Minimum input level 1 dB error -55C to +105C 01 -59 typical dBm Slope -55C to +105C 01 -27 -22 mV/dB Intercept -55C to +105C 01 17 24 dBm Output voltage - high power in PIN= -10 dBm -55C to +105C 01 0.63 0.83 V Output voltage - low power in PIN= -35 dBm -55C to +105C 01

23、 1.2 1.5 V Temperature sensitivity PIN= -10 dBm +25C to +105C 01 0.0056 typical dB/C -55C to +25C 0.0004 typical See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO.

24、 16236 DWG NO. V62/12665 REV PAGE 7 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TA Device type Limits Unit Min Max Measurement mode. VOUTpin shorted to VSETpin, sinusoidal input signal. f = 2.2 GHz, RTADJ= 500 . Input impedance 3/ +25C 01 391|0

25、.66 typical |pF 3 dB dynamic range +25C 01 65 typical dB -55C to +105C 62 typical 1 dB dynamic range +25C 01 58 typical dB Maximum input level 1 dB error -55C to +105C 01 -2 typical dBm Minimum input level 1 dB error -55C to +105C 01 -60 typical dBm Slope -55C to +105C 01 -28 -21.5 mV/dB Intercept -

26、55C to +105C 01 15 25 dBm Output voltage - high power in PIN= -10 dBm -55C to +105C 01 0.63 0.84 V Output voltage - low power in PIN= -35 dBm -55C to +105C 01 1.2 1.5 V Temperature sensitivity PIN= -10 dBm +25C to +105C 01 0.0052 typical dB/C -55C to +25C 0.0034 typical See footnotes at end of table

27、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 8 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TA Dev

28、ice type Limits Unit Min Max Measurement mode. VOUTpin shorted to VSETpin, sinusoidal input signal. f = 3.6 GHz, RTADJ= 51 . Input impedance 3/ +25C 01 119|0.7 typical |pF 3 dB dynamic range +25C 01 70 typical dB -55C to +105C 61 typical 1 dB dynamic range +25C 01 58 typical dB Maximum input level 1

29、 dB error -55C to +105C 01 -2 typical dBm Minimum input level 1 dB error -55C to +105C 01 -60 typical dBm Slope -55C to +105C 01 -24.3 typical mV/dB Intercept -55C to +105C 01 19.8 typical dBm Output voltage - high power in PIN= -10 dBm -55C to +105C 01 0.717 typical V Output voltage - low power in

30、PIN= -40 dBm -55C to +105C 01 1.46 typical V Temperature sensitivity PIN= -10 dBm +25C to +105C 01 0.0012 typical dB/C -55C to +25C 0.009 typical See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COL

31、UMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 9 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TADevice type Limits Unit Min Max Measurement mode. VOUTpin shorted to VSETpin, sinusoidal input signal. f = 5.8 GHz, RTADJ= 1000 .

32、 Input impedance 3/ +25C 01 33|0.59 typical |pF 3 dB dynamic range +25C 01 70 typical dB -55C to +105C 62 typical 1 dB dynamic range +25C 01 57 typical dB Maximum input level 1 dB error -55C to +105C 01 -1 typical dBm Minimum input level 1 dB error -55C to +105C 01 -58 typical dBm Slope -55C to +105

33、C 01 -24.3 typical mV/dB Intercept -55C to +105C 01 25 typical dBm Output voltage - high power in PIN= -10 dBm -55C to +105C 01 0.86 typical V Output voltage - low power in PIN= -40 dBm -55C to +105C 01 1.59 typical V Temperature sensitivity PIN= -10 dBm +25C to +105C 01 0.019 typical dB/C -55C to +

34、25C 0.0096 typical See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 10 TABLE I. Electrical performance characteristics Continued

35、. 1/ Test Symbol Conditions 2/Temperature, TA Device type Limits Unit Min Max Measurement mode. VOUTpin shorted to VSETpin, sinusoidal input signal. f = 8.0 GHz, RTADJ= 500 . 3 dB dynamic range +25C 01 60 typical dB -55C to +105C 58 typical Maximum input level 1 dB error -55C to +105C 01 3 typical d

36、Bm Minimum input level 1 dB error -55C to +105C 01 -55 typical dBm Slope -55C to +105C 01 -23 typical mV/dB Intercept -55C to +105C 01 37 typical dBm Output voltage - high power in PIN= -10 dBm -55C to +105C 01 1.06 typical V Output voltage - low power in PIN= -40 dBm -55C to +105C 01 1.78 typical V

37、 Temperature sensitivity PIN= -10 dBm +25C to +105C 01 0.032 typical dB/C -55C to +25C 0.0078 typical Output interface. VOUTpin. Voltage swing VSET= 0 V, PIN= -10 dBm, 4/ no load -55C to +105C 01 4.9 typical V VSET= 2.1 V, PIN= -10 dBm, 4/ no load 25 typical mV Output current drive VSET= 1.5 V, PIN=

38、 -50 dBm -55C to +105C 01 60 typical mA Small signal bandwidth SSBW PIN= -10 dBm, from CLPF to VOUT -55C to +105C 01 60 typical MHz Video bandwidth or envelope bandwidth -55C to +105C 01 45 typical MHz Output noise PIN= 2.2 GHZ, -10 dBm, fNOISE= 100 kHz, CLPF= 220 pF -55C to +105C 01 90 typical nV /

39、 Hz Fall time tFPIN= off to -10 dBm, 90% to 10% -55C to +105C 01 10 typical ns Rise time tRPIN= -10 dBm to off, 10% to 90% -55C to +105C 01 12 typical ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARI

40、TIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 11 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TA Device type Limits Unit Min Max VSETinterface. VSETpin. Nominal input range PIN= 0 dBm, 5/ measurement mode -55C to +10

41、5C 01 0.5 typical V PIN= -65 dBm, 5/ measurement mode 2.1 typical Logarithmic scale factor -55C to +105C 01 -0.04 typical dB/mV Bias current source PIN= -10 dBm, VSET= 2.1 V -55C to +105C 01 2.5 typical A Temperature reference TEMP pin Output voltage RLOAD= 10 k +25C 01 0.57 0.63 V Temperature slope

42、 RLOAD= 10 k -55C to +105C 01 2 typical mV/ C Source current +25C 01 10 typical mA Sink current +25C 01 0.1 typical mA Power down interface ENBL pin Logic level to enable to enable device -55C to +105C 01 1.7 typical V ENBL current when enabled ENBL = 5 V -55C to +105C 01 1 typical A ENBL current wh

43、en disabled ENBL = 0 V, sourcing -55C to +105C 01 15 typical A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12665 REV PAGE 12 TABLE I. Elec

44、trical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TA Device type Limits Unit Min Max Power interface. VPSI pins, VPSO pin. Supply voltage -55C to +105C 01 4.5 5.5 V Quiescent current ENBL = 5 V -55C to +105C 01 50 82 mA Quiescent current versus temperature -55C t

45、o +105C 01 150 typical A/ C Supply current when disabled ENBL = 0 V, total currents for VPSI and VPSO -55C to +105C 01 260 typical A Supply current when disabled versus temperature -55C to +105C 01 350 typical A 1/ Testing and other quality control techniques are used to the extent deemed necessary

46、to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or desig

47、n. 2/ Unless otherwise specified, VPOS= 5 V, CLPF= 220 pF, TA= 25C, and 52.3 termination resistor at INHI. 3/ The | symbolizes that the input impedance is being represented as the resistance value is in parallel with the capacitance. 4/ Controller mode. 5/ Gain = 1. For other gains, see the device datasheet. Provided by IHSNot for ResaleNo reproduction or networ