DLA DSCC-DWG-93078 REV D-2010 RESISTORS CHIP FIXED BULK METAL FOIL ULTRA PRECISION STYLE 2110.pdf
《DLA DSCC-DWG-93078 REV D-2010 RESISTORS CHIP FIXED BULK METAL FOIL ULTRA PRECISION STYLE 2110.pdf》由会员分享,可在线阅读,更多相关《DLA DSCC-DWG-93078 REV D-2010 RESISTORS CHIP FIXED BULK METAL FOIL ULTRA PRECISION STYLE 2110.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new source of supply. Update to present DoD policy requirements. Extensive editorial changes throughout. 14 July 1998 M. Radecki B Add Group B certification. Editorial changes throughout. 09 May 01 K. Cottongim C Removal of Vendor. Update to present DoD
2、 policy requirements. Extensive editorial changes throughout. 25 Jan 06 M. Radecki D Inactivation for new design. Editorial changes throughout. 19 Feb 10 M. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV D D D D D D D PAGES 1 2 3 4 5 6 7 PMIC N/A Orig
3、inal date of drawing 29 July 1994 PREPARED BY Heraldine Johnson DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH CHECKED BY Andrew R. Ernst TITLE RESISTORS, CHIP, FIXED, BULK METAL FOIL, ULTRA PRECISION, STYLE 2110 APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 93078 REV D PAGE 1 OF 7 A
4、MSC N/A 5905-E739 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC drawing 93078 is inactive for new design and is use for replacement purposes only. For new design, use DSCC drawing 06001 Provided by IHSNot for ResaleNo
5、reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 93078 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a bulk metal foil, ultra precision, chip resistor, style 2110. 1.2
6、Part or Identifying Number (PIN). The complete PIN is as follows: 93078 - * * Drawing number Resistance value (see 3.3.1) Tolerance (see 3.3.3) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handbooks form a part of t
7、his document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Re
8、liability, Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-690 - Failure Rate Sampling Plans and Procedures. MIL-STD-790 - Standard Practice for Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Op
9、tic Parts Specifications. * (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the ev
10、ent of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. R
11、EQUIREMENTS 3.1 Item requirements. The individual item requirements shall be as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-55342 and herein (see figure 1). Passivation is not applicable, however, a protective coatin
12、g over the element shall be provided. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 93078 REV D PAGE 3 L W T (max) D mm 5.21 Inch 0.205 mm 2.41 Inch 0.095 mm 0.64 I
13、nch 0.025 mm 0.46 Inch 0.018 NOTES: 1. Dimensions are in millimeters. Inch equivalents are given for general information only. 2. The pictorial view of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the en
14、velope and do not alter the functional aspects of the device, are acceptable. 3. Tolerances shall be 0.13 mm (0.005 inch) unless otherwise specified. FIGURE 1. Chip resistor. 3.3 Electrical characteristics. 3.3.1 Resistance. The nominal resistance expressed in ohms is identified by six characters, c
15、onsisting of five digits and a letter. The letter is used simultaneously as a decimal point and as a multiplier. For resistance values: a. Greater than or equal to 1 ohm but less than 1,000 ohms, the letter “R“ is used to represent a decimal point. b. Greater than or equal to 1,000 ohms but less tha
16、n 1 megohm, the letter “K“ is used to denote that a decimal point is located three places to the right. All digits preceding and following the letters (R or K) of the group represent significant figures. The resistance value designations are shown in table I. Minimum and maximum resistance values sh
17、all be as specified herein. The standard values for every decade shall follow the sequence specified in the 10 to 100 decade table of MIL-PRF-55342 for resistance tolerances D and F. The resistance values for tolerances Q, T, A, B, and C may be any value within the limits specified herein, but it is
18、 preferred that values be chosen from the “B“ column of the 10 to 100 decade table of MIL-PRF-55342. The resistance values for tolerance D shall follow the standard values listed under tolerance B of MIL-PRF-55342. 3.3.2 Resistance range. The resistance range shall be from 5 ohms to 100 kilohms (see
19、 3.3.6). 3.3.3 Resistance tolerance. Resistors are available in resistance tolerances as specified in table II and paragraph 3.3.3.1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO
20、. 14933 DWG NO. 93078 REV D PAGE 4 TABLE I. Designation of resistance values. Designation Resistance ohms 1R0000 to 9R8800 incl. 10R000 to 98R800 incl. 100R00 to 988R00 incl. 1K0000 to 9K8800 incl. 10K000 to 98K800 incl. 100K00 to 988K00 incl. 1.0 10.0 100 1000 10000 100000 to to to to to to 9.88 98
21、.8 988 9880 98800 988000 incl. incl. incl. incl. incl. incl. TABLE II. Resistance tolerance. Symbol Resistance tolerance percent T Q A B C D F 0.01 0.02 0.05 0.1 0.25 0.5 1.0 3.3.3.1 Resistance tolerance versus resistance value. The tightest resistance tolerance available is value specific as indica
22、ted by the following. Resistance (ohms) Tolerance (percent) 5 10 25 50 100 250 to to to to to to 10 25 50 100 250 100 ohms ohms ohms ohms ohms kohms 0.5 0.25 0.1 0.05 0.02 0.01 3.3.4 Power rating. The power rating for chip resistors shall be .200 watt at +70OC derated to +125OC at zero power (see fi
23、gure 2). 3.3.5 Voltage rating. The maximum continuous working voltage shall not exceed 140 volts. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 93078 REV D PAGE 5 F
24、IGURE 2. Derating curve. 3.3.6 Resistance temperature coefficient. The resistance temperature coefficient shall not exceed the values specified below: Characteristic Resistance range 20 ppm/OC 5 ohms to 50 ohms 10 ppm/OC 50 ohms to 100 ohms 5 ppm/OC 100 ohms to 100 kohms 3.3.7 Termination. The termi
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLADSCCDWG93078REVD2010RESISTORSCHIPFIXEDBULKMETALFOILULTRAPRECISIONSTYLE2110PDF

链接地址:http://www.mydoc123.com/p-688996.html