DLA DSCC-DWG-93044 REV A-2002 JUMPER SHUNT 100 INCH CENTERLINE 025 INCH SQUARE MATING PIN GENERAL DRAWING《中心线 100英寸 025英寸方形匹配PIN跳线帽总图》.pdf

《DLA DSCC-DWG-93044 REV A-2002 JUMPER SHUNT 100 INCH CENTERLINE 025 INCH SQUARE MATING PIN GENERAL DRAWING《中心线 100英寸 025英寸方形匹配PIN跳线帽总图》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-93044 REV A-2002 JUMPER SHUNT 100 INCH CENTERLINE 025 INCH SQUARE MATING PIN GENERAL DRAWING《中心线 100英寸 025英寸方形匹配PIN跳线帽总图》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Change CAGE 14933 to 037Z36. Replaced cancelled military specifications with industry equivalents. Editorial changes throughout. 3 October 2002 R. Heber Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A A A A A A A A A REV STATUS OF PAGES PAGE

2、1 2 3 4 5 6 7 8 9 10 11 12 13 PREPARED BY PMIC N/A William Carpenter DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE James P. Donohue APPROVED BY Randy Larson JUMPER SHUNT, .100 INCH CENTERLINE, .025 INCH SQUARE PIN, GENERAL DRAWING SIZE CAGE CODE 037Z3 DWG. NO. 93044 Orig

3、inal date of drawing 21 June 1994 A REV A PAGE 1 OF 13 AMSC N/A 5935-E643-44 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93044 DEFENSE

4、SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing covers the requirements for low profile jumper connectors, for use with unshrouded or free standing, .025 inch (0.64 mm) square pin headers, on .100 inch (2.54 mm) centers, for use in low power applicatio

5、ns requiring interconnection of two adjacent terminals. 1.2 Part or Identifying Number (PIN). The complete PIN shall be in accordance with the detail drawing. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, an

6、d handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are these listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATIO

7、NS DEPARTMENT OF DEFENSE MIL-M-24519 - Molding Plastic, Electrical, Thermoplastic. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-202 - Electronic and Electrical Component Parts. MIL-STD-1344 - Test Methods for Electrical Connectors. (Unless otherwise indicated, copies of the above specifications, standard

8、s, and handbook are available from the Defense Printing Service, Detachment Office, Building 4D, Customer Service, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise

9、specified, the issues of documents, which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation. AMERICAN NATIONAL STANDARDS INSTITU

10、TE, INC. (ANSI) ANSI/NCSL Z540.1 - Laboratories Calibration and Measuring and Test Equipment. (Applications for copies should be addressed to the American National Standards Institute, 25 West 43rdStreet, New York, NY 10036.) Provided by IHSNot for ResaleNo reproduction or networking permitted witho

11、ut license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93044 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 3 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B103 - Plate, Phosphor Bronze, Sheet, Strip, and Rolled Bar. ASTM B139 - Rod, Phosphor Bronze, Bar, and Shapes. AST

12、M B159 - Phosphor Bronze Wire. ASTM B488 - Standard Specification for Gold for Engineering Uses, Electrodeposited Coating of. ASTM D4066 - Nylon Injection and Extrusion Materials (PA). (Applications for copies should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Dr.

13、, West Conshohocken, PA 19428). COPPER DEVELOPMENT ASSOCIATION INC. CuZn30 H14 - Copper Alloy No. CDA260. (Applications for copies should be addressed to the Copper Development Association, Inc. 405 Lexington Avenue, New York, NY 10017.) UNDERWRITERS LABORATORIES INC. (UL) ANSI/UL 94 - Plastic Mater

14、ials for Parts in Devices and Applications, Tests for Flammability of. (Applications for copies should be addressed to the Comm 2000, 1418 Brook Drive, Downers Grove, IL 60515-1025.) SOCIETY OF AUTOMOTIVE ENGINEERS INC. (SAE) SAE-AMS-QQ-N-290 - Nickel Plating (Electrodeposited). (Applications for co

15、pies should be addressed to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096-0001). (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or th

16、rough libraries or other informational services.) 2.3 Order of precedence. The individual item requirements shall be in accordance with DSCC detail drawing and as specified herein. In case of conflict between this drawing and the detail drawing, the latter shall govern. 3. REQUIREMENTS 3.1 DSCC requ

17、irements drawing. The individual requirements shall be in accordance with the applicable item requirements drawing. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in the applicable item requirements drawing and herein. 3.3 M

18、aterial. The material for each part shall be as specified herein, or equivalent. Substitute material shall meet the performance requirements of this drawing. 3.3.1 Contact body. The contact body shall be phosphor alloy in accordance with ASTM B139, ASTM B159 or CuZn30 H14 in accordance with CDA260 o

19、r one-half hard phosphor bronze strip in accordance with ASTM B139. 3.3.2 Insulator housing. The insulator shall be nylon or glass-mineral-filled in accordance with ASTM D4066 or glass filled thermoplastic in accordance with MIL-M-24519. All plastic material shall be flammability rated V-0 in accord

20、ance with ANSI/UL-94. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93044 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 4 3.4 Finish. 3.4.1 Contact body. The body shall be plated with 30 microinch

21、es (0.76 m) minimum of gold in accordance with ASTM B488, type 3, code C, class 0.76 in the contact area (preplating is permissible) over 50 microinches (1.27 m) minimum of nickel in accordance with SAE-AMS-QQ-N-290, class 2. NOTE: When contacts have been provided in strip form, the absence of plati

22、ng in the area where the contact was removed from the strip is acceptable provided it is in a nonfunctional area and any corrosion formed as a result of salt spray testing does not creep into contact mating area. 3.5 Design and construction. The receptacle shall be a two-piece assembly having two in

23、terconnected contacts retained in a plastic housing. The female end of the contact shall interface with .025 inch (0.64 mm) square pins on .100 inch (2.54 mm) centers. 3.5.1 Mating. The connector shall be capable of mating and unmating by hand without the use of special tools. 3.5.2 Workmanship. Con

24、nectors shall be uniform in quality and shall be free from burrs, scratches, cracks, voids, chips, blisters, holes, sharp edges, or other defects that will adversely affect life or serviceability. 3.6 Electrical characteristics. 3.6.1 Current rating. The maximum current rating of the connector shall

25、 be 3.0 amperes dc. 3.6.2 Contact resistance. The contact resistance when measured in accordance with MIL-STD-202, method 307, shall not exceed 15 milliohms, before test and 20 milliohms, after test; the following details shall apply: a. Method of connection: Attach current and voltage leads as show

26、n on figure 1. b. Test current: 1.0 ampere dc. c. Sample size: 20 percent of connector population. NOTE: Different in contact resistance between various terminal configurations represent changes in the bulk resistance due to longer lengths of currents paths; correction for these differences in bulk

27、resistance will permit comparison of results for different styles of terminal, see 3.6.4 and 3.6.5. 3.6.3 Low level circuit resistance. The low level circuit resistance shall not exceed the value specified in 3.6.2 when measured in accordance with MIL-STD-1344, method 3002, the following details sha

28、ll apply: a. Method of connection: Attach current and voltage leads as shown on figure 1. b. Test current: 1.0 milliampere dc. c. Minimum open circuit voltage: 20 millivolts dc. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 0

29、37Z3 93044 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 5 FIGURE 1. Contact resistance. 3.6.4 Insulation resistance. The insulation resistance of unmated connectors shall not be less than 50,000 megohms (20,000 megohms after exposure of the humidity environment described in 3

30、.8.1) when measured in accordance with MIL-STD-202, method 302, the following details shall apply: a. Test conditions: B (500 volts dc). b. Point of measurement: Between header posts and outside bottom of shunt insulator closes to the contact body. 3.6.5 Dielectric withstanding voltage. There shall

31、be no evidence of arc-over, insulation breakdown or excessive leakage current (1 milliampere) when the unmated connectors are tested in accordance with MIL-STD-202, method 301, the following details shall apply: a. Test potential: 800 volts rms at 60 Hz. b. Test duration: 60 seconds. 3.6.6 Capacitan

32、ce. The capacitance between pairs of adjacent or opposing contacts, in an unmated connector, shall not exceed 2.0 picofarads when measured, in accordance with MIL-STD-202, method 305, the following details shall apply: Test frequency: 100 kilohertz. 3.7 Mechanical characteristics. 3.7.1 Contact rete

33、ntion. The contact pair shall not be dislodged from the housing when an axial force, specified in table I, is applied in the direction of mating pin insertion. The force shall be applied at a crosshead speed of 0.10 inch (2.5 mm) per minute and the maximum load shall be maintained for 10 seconds. 3.

34、7.2 Total mating force. The total force to the terminated connector with an appropriately populated header consisting of properly configured see figure 2, .025 inch (0.06 mm) square pins shall be 350 gram force (12.3 ozf) average. 3.7.3 Total contact insertion force. When measured using a maximum ga

35、uge configured as shown on figure 3 or 4, the shunt insertion force shall not exceed the values specified in table I. 3.7.4 Total contact withdrawal force. After three insertions of a maximum gauge, the force required to withdraw a minimum gauge, configured as shown on figure 3 or 4, shall be not le

36、ss than the values specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93044 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 6 TABLE I. Shunt contact force. Shunt contact force-grams

37、 Shunt style Insertion (max) Withdrawal (min) Force/contact In composite connector (grams-max) Low profile Mini shunt 709 1200 40 30 300 450 3.7.5 Durability. After 50 mating cycles the individual contact withdrawal force shall be not less than the values shown in table I, see 3.6.2, the following d

38、etails shall apply: a. Gold plating thickness: 30 microinches (0.76 m). b. Spring thickness: 3.5 mils (88.9 m). 3.8 Environmental conditions. 3.8.1 Humidity. Within 1 hour after exposure of the mated connector to a high humidity environment, the insulation resistance of an unterminated connector sha

39、ll not be less than 1,000 megohms (see 3.6.4), and the contact resistance of a terminated connector shall not exceed the value specified in 3.6.2. The test shall be in accordance with MIL-STD-202, method 103 (excluding steps 7a and 7b); the following details shall apply: Test duration: 240 hours. 3.

40、8.2 Thermal shock. After exposure of an unmated connector to alternate periods of extreme high and low temperature, there shall be no evidence of cracking of crazing of the insulator housing or other physical damage to the connector. After the test the dielectric withstanding voltage of an untermina

41、ted connector shall not be less than the appropriate value specified in 3.6.5 and the contact retention shall not be less than 2 pounds, see 3.7.1. The test shall be in accordance with MIL-STD-202, method 107, test condition A; the following details shall apply: a. Test condition: A (five, 1 hour cy

42、cles). b. Temperature range: -55C to +120C. c. Exposure time at each temperature: 30 minutes, minimum. d. Transfer time: 30 seconds, maximum. 3.8.3 High temperature life. After exposure of the connector to a high temperature operating environment, the contact resistance shall not exceed the value sp

43、ecified in 3.6.2, the following details shall apply: a. Test chamber temperature: 120C of contact under load. b. Test duration: 200 hours. c. Points of measurement: Between adjacent and opposing contact positions for 20 percent of connector population. Provided by IHSNot for ResaleNo reproduction or

44、 networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93044 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 7 Inches mm .001 .008 .015 .025 .100 0.03 0.20 0.38 0.06 2.54 NOTES: 1. Plating 30 microinches (0.76 m) minimum gold in accordance with ASTM B488

45、, type 3, code C, class 0.76 over 50 microinches (1.27 m) (minimum) nickel in accordance with AMS-QQ-N-290, class 2. 2. Measured at Datum-D-with part in restrained (flat) condition. 3. Length to insure contact with female terminal interface. 4. Unless otherwise specified, tolerances are .005 inch (0

46、.13 mm). FIGURE 2. Mating header. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93044 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 8 Dimensions - Inches Gauge A Tolerance B Tolerance Min .0240 +.

47、0000 .025 .001 -.0002 Max .0260 +.0002 .025 .001 -.0000 Inches mm .001 .0002 .015 .0240 .025 .0260 .750 0.02 0.005 0.38 0.609 0.06 0.660 19.05 Material: Shim stock; grind to width and break edges; do not polish working surface. Clean gauge as follows before each use: a. Scour surface with mildly abr

48、asive material (rubber eraser, e.g.). b. Wash surface and dry with clean cotton. DO NOT TOUCH SURFACE WITH FINGERS. FIGURE 3. Insertion/withdrawal force gauge low profile shunt. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 0

49、37Z3 93044 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 9 Dimensions - Inches Gauge A Tolerance B Tolerance Min .0240 +.0000 .025 .001 -.0002 Max .0260 +.0002 .025 .001 -.0000 Inches mm Inches mm .001 .0002 .015 .0240 .025 0.02 0.005 0.38 0.609 0.06 .0260 .40 .500 .60 0.660 10.2 12.70 15.2 Material: Shim stock; grind to width and break edges; do not polish working surface. Clea