DLA DSCC-DWG-93037 REV B-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL 45 DEG INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES III AND IV CONN.pdf

《DLA DSCC-DWG-93037 REV B-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL 45 DEG INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES III AND IV CONN.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-93037 REV B-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL 45 DEG INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES III AND IV CONN.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、NOTICE OF REVISION (NOR) I This revision described below has been authorized for the document listed. 1. DATE (WMMDD) 04-05-07 4. ORIGINATOR a. TYPED NAME (First, Middle Initial, Last) Jeffery Tunstall b. ADDRESS (Street, City, State, Zip Code) 5. CAGE CODE Defense Supply Center Columbus 03723 3990

2、East Broad Street Columbus, Ohio 43216-5000 7. CAGE CODE 03723 ALL 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES a. CURRENT A Form Approved 0188 OMB NO. 0704- b. NEW B 2. PROCURING ACTIVITY NO. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT 3. DDAAC c. TYPED NAME (First, Middle In

3、itial, Last) 6. NOR NO. 5935-R034-03 8. DOCUMENT NO. 93037 ECPNO. NIA 13. DESCRIPTION OF REVISION Page 3, figure 1: Add “Max cable range“ column to accessory shell size table, as shown to the left. n7 FI Page 5, Vendor CAGE number table Delete: “390HA005“ and substitute: “390HB005“. I 1 a. (X one) 1

4、 X I (1) Existing document supplemented by the NOR may be used in manufacture. I DSCC-VAI I d. TITLE CHIEF,INTERCONNECTION DEVICES 15a. ACTIVITY ACCOMPLISHING REVISION DSCC-VAI DD Form 1695, APR 92 I e. SIGNATURE Richard L. Talyor b. REVISION COMPLETED (Signature) Jeffery Tunstall Previous editions

5、are obsolete Richard L. Tavlor f. DATE SIGNED (04-05-07) c. DATE SIGNED (04-05-07) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-LTR A Correcting references. Correcting address list of sources. DESCRIPTION DATE Update format. 16 July 02 APPROVED RE

6、V A Robert Heber PAGE 1 OF 5 I MIC NIA Original date of drawing 14 November 1994 PREPARED BY Jeffery Tunstall CHECKED BY Abdo Abdouni APPROVEDBY Robert Heber DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS. OHIO 43216-5000 TITLE CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, 45“, INDIVIDUAL A

7、ND /OR OVERALL SHIELD TERMINATION, CATEGORY 2A (FOR MIL-DTL-38999 SERIES 111 and IV CONNECTORS) CAGE CODE IZE A I 03723 DWG. NO. 93039 iMSC NIA Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TION KNURL STYLE MFR OPTION - TYP STYLE A DESIGN OPTIONAL

8、v- GROMMET - -. 135 MAX 4 r CABLE RANGE STYLE B STYLE C FIGURE 1. Dimensions and confiquration. CAGE CODE DWG NO. 03723 93037 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 Accessory 1 A di

9、a max I E max I F max NOTES: 1. Dimensions are in millimeters. Inch-pound equivalents are in parentheses. 2. Dimensions apply after plating. 3. The U.S. Government preferred system of measurements is the metric SI system. However, this item was originally using inch-pound units of measurement, in th

10、e event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Dimensions and confiauration - Continued. CAGE CODE DWG NO. 03723 93037 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or network

11、ing permitted without license from IHS-,-,-REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 2A. Backshell shall be capable of terminating individual andlor overall shields or double overall shields and provide an environmental seal. Design and construction: See figure 1. Interface dim

12、ensions shall confirm to MIL-C-85049 accessory intermateability data for MIL-DTL-38999 series 111 and IV connectors. Material: Accessory components: Aluminum alloy shall be in accordance with MIL-C-85049. O-ring and grommet: Shall be in accordance with MILC-85049. Finish: N, and W shall be in accord

13、ance with MIL-C-85049. Finish N is for space application only. Part or Identifying Number (PIN): The PIN shall be in accordance with the following: Example: 93037 11 - 05 Drawing number Shell size (see figure I) Finish Strain relief style Cable accommodation range Marking: Marking shall be in accord

14、ance with MIL-C-85049 except the PIN shall be as stated above. QUALIFICATION: Qualification inspection: Qualification inspection for the adapter specified herein shall not be required. Qualification conformance inspection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in

15、 accordance with MIL-C-85049. Methods of inspection: Shall be in accordance with MIL-C-85049. CAGE CODE DWG NO. 03723 93037 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Approved sources of

16、supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing Vendor CAGE number - PIN 11 93037* - 11 Parts must be pu

17、rchased to this DSCC PIN to assure that all performance requirements and tests are met. 31461 06324 E4030A 390HA005 Vendor CAGE number Vendor name and address 31461 06324 Electro Adapter, Incorporated 20640 Nordhoff Street Chatsworth, CA 9131 1 Glenair, Incorporated 121 1 Air Way Glendale, CA 91201-2497 CAGE CODE DWG NO. 03723 93037 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-