DLA DSCC-DWG-93027 REV D-2013 INDUCTOR SURFACE MOUNT LEADLESS.pdf

《DLA DSCC-DWG-93027 REV D-2013 INDUCTOR SURFACE MOUNT LEADLESS.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-93027 REV D-2013 INDUCTOR SURFACE MOUNT LEADLESS.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LT DESCRIPTION DATE APPROVED A Add Source of Supply 23 February 1998 David E. Moore B Changes in accordance with NOR 5950-R001-98. Added an additional Source of Supply. 15 May 2003 Kendall Cottongim C Change Source of Supply Address. Update drawing to current format and update referenced d

2、ocuments. 18 April 2006 Michael Radecki D Addition of pure tin prohibition requirement. Update drawing format throughout. 26 June 2013 Michael Radecki THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV D D D D D D D PAGES 1 2 3

3、 4 5 6 7 PMIC N/A PREPARED BY Ken R. Beymer DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing CHECKED BY Tony J. Westphal TITLE INDUCTOR, SURFACE MOUNT, LEADLESS 27 Nov 1993 APPROVED BY Bud Boulter SIZE A CODE IDENT. NO. 14933 DWG NO. 93027 REV D PAGE 1

4、 OF 7 AMSC N/A 5950-2013-E09 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE

5、 A CODE IDENT NO. 14933 DWG NO. 93027 REV D PAGE 2 SCOPE 1.1 Scope. This drawing describes the requirements for a surface mount inductor. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 93027 -001 | | | | Drawing Dash number number 2. APPLICABLE DOCUMENTS

6、 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the solicitation or contract (s

7、ee 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-PRF-27 - Transformers and Inductors (Audio, Power and High-Power Pulse), General Specification STANDARDS DEPARTMENT OF DEFENSE MIL-STD-130 - Identification Marking of U.S. Military Property. MIL-STD-202 - Test methods for Electronic and electrical Co

8、mponent Parts. MIL-STD-1276 - Leads for Electronic Component Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the Standardization Documents order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of

9、a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or netwo

10、rking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 93027 REV D PAGE 3 3. REQUIREMENTS 3.1 Design and construction. 3.1.1 Dimensions and configurations: Dimensions and configuration shall be as specified in figure 1 and in t

11、able I. 3.1.2 Case. The case shall be molded using fiber filled epoxy. 3.1.3 Terminals. The terminals shall be tin-lead plated phosphor bronze. 3.1.4 Altitude. 70,000 feet. 3.1.5 Operating temperature range. The operating temperature range shall be -55C to +125C. 3.2 Temperature rise. The temperatur

12、e rise shall be 35C over ambient temperature of 90C. 3.3 Marking location. Marking shall be on top of the case. Marking shall be in accordance with 1.2 herein. Also, the similar vendor part may also be marked in accordance with 6.5 herein. 3.4 Electrical ratings. 3.4.1 Inductance. Inductance shall b

13、e as specified in table I. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promot

14、es economically advantageous life cycle costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.7 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and external

15、ly. Tin content of transformer components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.8 Manufacturer eligibility. To be eligible for listing as an approved source of supply, the manufacturer shall be listed on the MIL-P

16、RF-27 qualified products list for at least one part or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.9 Workmanship. The inductors shall be processed in such a manner as to be uniform and free of defects that w

17、ill affect life, serviceability or function. 4. VERIFICATION 4.1 Qualification inspection. Qualification for this part is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections of MIL-PRF

18、-27. 4.2.2 Group A inspection. Group A inspection shall be in accordance with MIL-PRF-27. 4.2.3 Group B inspection. Group B inspection shall be in accordance with MIL-PRF-27. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY

19、CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 93027 REV D PAGE 4 4.2.4 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2). 5. PACKAGING 5.1 Packaging. For acquisition purpo

20、ses, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements ar

21、e maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM produ

22、cts, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Devices conforming to this drawing are intended for use when military specifications do not exist and

23、 qualified military devices that perform the required function are not available for OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2) b. Requirements for delivery of one copy of the conformance inspection data with each shipme

24、nt of parts by the manufacturer (when applicable, see 4.2.4). c. Whether the inductor should be taped and reeled for automatic insertion equipment. d. Requirements for notification of change of product to acquiring activity, if applicable. e. Requirements for packaging and packing. f. Whether the in

25、ductor should be taped and reeled for automatic insertion equipment. 6.3 Replaceability. Devices covered by this drawing will replace the same commercial device covered by a contractor-prepared specification or drawing. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 perce

26、nt, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will no

27、t prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Users of record. Coordination of this documen

28、t for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at Transformerdla.mil, or if in writing to: DLA Land and Maritime, Columbus, ATTN: DSCC-VAT, Post

29、Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0557 or DSN 850-0557. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 93027 REV D PAGE 5 Size E max

30、Millimeters (inches) F max Millimeters (inches) G 1/ Millimeters (inches) A 6.60 (.260) 5.84 (.230) 2.16 (.085) B 10.41 (.410) 5.84 (.230) 3.43 (.135)C 10.41 (.410) 7.87 (.310) 3.43 (.135) D 13.59 (.535) 7.87 (.310) 5.08 (.200)1/ The tolerance for all dimensions shall be 0.25 mm (.010 inch). mm Inch

31、es 0.25 .010 0.64 .025 NOTES: 1. Dimensions are in millimeters. 2. Inch-pound equivalents are given for general information only. 3. The US Government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in t

32、he event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Dimensions and configurations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A C

33、ODE IDENT NO. 14933 DWG NO. 93027 REV D PAGE 6 TABLE I. Electrical characteristics. PIN 93027- Series Parallel Configur- ation Power rating (mW) Inductance 10 percent (mH) Rated dc current (mA) DC resistance (max) Inductance 10 percent (mH) Rated dc current (mA) DC resistance (max) 001 0.100 300 1.6

34、0 0.025 600 0.400 A 125 002 0.100 600 0.96 0.025 1200 0.240 B 250 003 0.100 780 0.37 0.025 1560 0.093 C 300 004 0.100 1350 0.21 0.025 2700 0.053 D 450 005 0.250 200 3.11 0.062 400 0.778 A 125 006 0.250 400 1.98 0.062 800 0.495 B 250 007 0.250 530 0.82 0.062 1060 0.205 C 300 008 0.250 930 0.41 0.062

35、1860 0.103 D 450 009 0.500 150 6.14 0.125 300 1.535 A 125 010 0.500 300 3.35 0.125 600 0.838 B 250 011 0.500 380 1.62 0.125 760 0.405 C 300 012 0.500 660 0.82 0.125 1320 0.205 D 450 013 0.750 120 9.45 0.187 240 2.363 A 125 014 0.750 250 5.20 0.187 500 1.300 B 250 015 0.750 310 2.50 0.187 620 0.625 C

36、 300 016 0.750 540 1.25 0.187 1080 0.313 D 450 017 1.000 95 12.85 0.250 190 3.213 A 125 018 1.000 200 6.90 0.250 400 1.725 B 250 019 1.000 270 3.37 0.250 540 0.843 C 300 020 1.000 570 1.87 0.250 940 0.468 D 450 021 2.000 75 25.60 0.500 150 36.400 A 125 022 2.000 150 12.20 0.500 300 3.050 B 250 023 2

37、.000 190 6.75 0.500 380 1.690 C 300 024 2.000 330 3.62 0.500 660 0.910 D 450 025 3.000 60 38.40 0.750 120 9.600 A 125 026 3.000 120 18.30 0.750 240 4.580 B 250 027 3.000 160 10.12 0.750 320 2.530 C 300 028 3.000 270 5.50 0.750 540 1.380 D 450 029 5.000 45 64.00 1.250 90 16.000 A 125 030 5.000 90 30.

38、40 1.250 180 7.600 B 250 031 5.000 120 16.87 1.250 240 4.220 C 300 032 5.000 210 9.12 1.250 420 2.280 D 450 033 7.500 30 96.00 1.875 60 24.000 A 125 034 7.500 70 46.00 1.875 140 11.500 B 250 035 7.500 100 25.37 1.875 200 6.350 C 300 036 7.500 170 13.75 1.875 340 3.440 D 450 037 10.000 20 128.00 2.50

39、0 40 32.000 A 125 038 10.000 50 61.00 2.500 100 15.250 B 250 039 10.000 80 33.75 2.500 160 8.440 C 300 040 10.000 140 18.25 2.500 280 4.570 D 450 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CO

40、DE IDENT NO. 14933 DWG NO. 93027 REV D PAGE 7 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at Transformerdla.mil, or by contacting DLA Land and Mar

41、itime, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0557 or DSN 850-0557. DLA Land and Maritime PIN 93027- Vendors similar 1/ Vendor CAGE Vendors name and address 001 93001 22558 Coast/Advanced Chip Magnetics 4225 Spencer Street Torrance, CA 90503

42、 002 93002003 93003004 93004 005 93005006 93006007 93007 008 93008009 93009010 93010 011 93011012 93012013 93013 014 93014015 93015016 93016 017 93017018 93018019 93019 020 93020021 93021022 93022 023 93023024 93024025 93025 026 93026027 93027028 93028 029 93029030 93030031 93031 032 93032033 93033034 93034 035 93035036 93036037 93037 038 93038039 93039040 93040 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-