DLA DSCC-DWG-89110 REV A-2002 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL STRAIGHT EMI RFI HYBRID CONSTRUCTION CATEGORY 3C《环境射频干扰 电磁干扰混合建造竖直进入背面外壳连接附件 3C类》.pdf

《DLA DSCC-DWG-89110 REV A-2002 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL STRAIGHT EMI RFI HYBRID CONSTRUCTION CATEGORY 3C《环境射频干扰 电磁干扰混合建造竖直进入背面外壳连接附件 3C类》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-89110 REV A-2002 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL STRAIGHT EMI RFI HYBRID CONSTRUCTION CATEGORY 3C《环境射频干扰 电磁干扰混合建造竖直进入背面外壳连接附件 3C类》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 PREPARED BY PMIC N/A Jeffery Tunstall DEFENSE

2、 SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Abdo Abdouni APPROVED BY Robert Heber CONNECTOR, ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, STRAIGHT EMI/RFI HYBRID CONSTRUCTION, CATEGORY 3C SIZE CAGE CODE 037Z3 DWG. NO. 89110 Original date of drawing 26 July 90 A REV A PA

3、GE 1 OF 9 AMSC N/A 5935-E669 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000

4、A REV A PAGE 2 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 3 Shell size Shell size code C dia max D ma

5、x E max 9 A .800 .540 .130 11 B .910 .540 .130 13 C 1.100 .615 .130 15 D 1.210 .615 .130 17 E 1.290 615 .130 19 F 1.440 .615 .130 21 G 1.570 .615 .130 23 H 1.700 .615 .130 25 J 1.830 .615 .130 FIGURE 1. Dimensions and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networkin

6、g permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 4 H max (length code) Shell size Cable entry size code F dia min G dia max 1 2 A .172 .220 B .216 .255 9 C .247 .286 1.515 3.015 C .245 .286 D .270 .310 E

7、.292 .340 F .307 .370 11 G .370 .411 1.515 3.015 F .307 .370 G .370 .411 13 H .425 .505 F .307 .370 G .370 .411 H .425 .505 15 J .545 .625 1.515 3.015 H .424 .506 J .544 .626 K .644 .756 17 L .805 .885 1.515 3.015 H .425 .505 J .545 .625 K .665 .755 19 L .805 .885 1.515 3.015 Provided by IHSNot for

8、ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 5 FIGURE 1. Dimensions and configuration Continued. H max (length code) Shell size Cable entry size code F dia min G dia

9、max 1 2 J .545 .625 K .665 .755 L .805 .885 21 M .915 1.005 1.515 3.015 J .545 .625 K .665 .755 L .805 .885 M .915 1.005 23 N 1.035 1.125 1.515 3.015 L .804 .886 M .914 1.006 N 1.034 1.126 25 P 1.116 1.198 1.515 3.015 FIGURE 1. Dimensions and configuration Continued. Provided by IHSNot for ResaleNo

10、reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 6 Inches mm Inches mm Inches mm Inches mm .130 3.30 .411 10.44 .755 19.18 1.100 27.94 .172 4.37 .424 10.77 .756 19.20 1.116 28.35

11、.216 5.49 .425 10.80 .800 20.32 1.125 28.58 .220 5.59 .505 10.83 .805 20.45 1.126 28.60 .245 6.22 .506 12.85 .885 22.48 1.198 30.43 .247 6.27 .540 13.72 .886 22.50 1.210 30.73 .255 6.48 .544 13.82 .910 23.11 1.290 32.77 .270 6.86 .545 13.84 .914 23.22 1.440 36.58 .286 7.26 .615 15.62 .915 23.24 1.51

12、5 38.48 .292 7.42 .625 15.87 1.005 25.53 1.570 39.88 .307 7.80 .626 15.90 1.006 25.55 1.700 43.18 .310 7.87 .664 16.87 1.034 26.26 1.830 46.48 .340 8.64 .665 16.89 25.55 26.29 3.015 76.58 .370 9.40 NOTES: 1. Dimensions are inches. 2. Metric equivalents are given for general information only. 3. Meta

13、llic material inner shell must have solid surface through the length “H” and inner circumference of the shell. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000

14、A REV A PAGE 7 Figure 1. Dimensions and configuration Continued. SCOPE This is an extended environment-resisting hybrid construction (metal and nonmetallic inner shell components, nonmetallic coupling nut) backshell. Metallic components are finished with olive drab cadmium plate over a suitable unde

15、rplate. Nonmetallic components are uncoated for corrosion resistance. REQUIREMENTS Backshells shall meet the requirements of MIL-C-85049, category 3C, class W with the following exceptions and additions. Dimensions and configuration: See figure 1 for interface dimensions that shall confirm to MIL-DT

16、L-38999, series III. Salt spray (corrosion): The backshells shall meet the dynamics salt spray requirements of MIL-C-85049, with the following exceptions and additions. The backshells shall be tested 2000 hours. Hydrolytic stability: The backshell shall be subjected to the following tests: a. Measur

17、e backshell weight. b. Boil in distilled water until no further weight gain is observed. c. Backshell may be dried with filtered compressed air. d. When backshell weight has stabilized, measured percent total weight gain, mating dimensions and length. e. Backshell shall be tested in accordance with

18、the thread strength of MIL-C-85049, category, 3C. e. Inspection of the backshell for damage. The backshell shall be without defects detrimental to mechanical performance. Total weight gain shall be less than 0.75 percent. When subjected to coupling thread strength specified in MIL-C-85049, there sha

19、ll be no evidence of cracking, breaking, or loosening of parts. Lighting strike: Backshells mated with matched construction connectors shall be subjected to a simulated lighting current pulse exposure. The current pulse shall be applied by a suitable high current generator and the current Provided b

20、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 8 waveform shall be monitored and recorded by a current transformer (or current shunt) and storage oscillosc

21、ope. The test pulse shall be a damped sinusoid with a basic frequency of 21 kHz and an amplitude decay time of 140 microseconds to 37 percent of its peak value. Pulse amplitude decay time of 140 microseconds to 37 percent of its peak value. Pulse amplitude shall be 60 kA. The receptacle connector sh

22、all be mounted on a simulated panel, using its normal mounting provisions. The simulated current pulse shall be applied between the plug accessory and the receptacle mounting panel. Upon completion of the pulse application, and without disturbing the test sample, the shell-to shell conductivity test

23、 of MIL-DTL-38999 shall be performed. When the electrical measurements have been completed, the sample shall be inspected in both the mated and unmated condition for evidence of damage from the simulated lighting current pulse. Part or Identifying Number (PIN): The PIN shall be in accordance with th

24、e following example: 89110- 11 E 1 Drawing number Shell size Cable entry size code Length code Marking: Marking shall be in accordance with MIL-C-85049 except the PIN shall be as stated above. Application guidance: To obtain full extended performance as specified above, this backshell must be assemb

25、led with the application hybrid connector, as specified on drawing 89090, 89093, and 89094. QUALIFICATION Qualification inspection: Qualification inspection for the backshells specified herein shall not be required. Qualification conformance inspection: Shall be in accordance with MIL-C-85049, unles

26、s otherwise specified. Inspection of packaging: Shall be in accordance with MIL-C-85049, unless otherwise specified. Methods of inspection: Shall be in accordance with MIL-C-85049, unless otherwise specified. Approved sources of supply. Approved sources are listed herein. Additional sources will be

27、added as they become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ Replacement military specification PIN Provided by IHSNot for ResaleNo reproduction or netwo

28、rking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 89110 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 9 2/ 89110-* 24805 BC0012- BG*-* N/A 1/ Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requ

29、irements of this drawing. 2/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 24805 ESC, Inc. 14115 Chadron Avenue Hawthorne, CA 90251 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-