DLA DSCC-DWG-88065 REV B-2008 CONNECTOR ELECTRICAL HARDWARE SERIES TRB.pdf

《DLA DSCC-DWG-88065 REV B-2008 CONNECTOR ELECTRICAL HARDWARE SERIES TRB.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-88065 REV B-2008 CONNECTOR ELECTRICAL HARDWARE SERIES TRB.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Part number and source update. Editorial changes throughout. 14 June 2001 Robert Heber B Remove Kings Electronics as a source 31 October 2008 Abdonasser AbdouniPrepared in accordance with ASME Y14.100 Source Control Drawing REV PAGE REV B B B B REV STATUS OF

2、 PAGES PAGE 1 2 3 4 PREPARED BY PMIC S Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE C. W. Koeller APPROVED BY Richard Marbais CONNECTOR, ELECTRICAL, HARDWARE, SERIES TRBSIZE CAGE CODE 037Z3 DWG. NO.88065 Original date of drawing 21 Nov 1988 A REV B PAGE 1 OF 4

3、AMSC N/A 5935-E822-000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 88065 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REVB PAGE2 Item Material Description 1 2 3 4 Silicone Brass Cres Nylon Gasket Cap Wire

4、 rope Rope insulation Caps shall be silver plated 0.0002 inch, minimum. Inches mm Inches mm .002 0.05 .141 3.58 .091 2.31 .56 14.22 .097 2.46 .70 17.78 NOTES: 1. Cap shall mate with series TRB in accordance with MIL-PRF-49142. 2. Materials used shall conform to MIL-PRF-49142. 3. Dimension A: 4 .25 i

5、nches. 4. Dimensions are in inches. Metric equivalents are given for information only. FIGURE 1. TRB cap. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 88065 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV

6、B PAGE3 REQUIREMENTS: (DSCC drawing 84148 is applicable.) Dimensions and configurations: See figure 1 herein. Corrosion: Applicable. After exposure, hardware shall be washed, shaken, and lightly brushed as specified in method 101 of MIL-STD-202, and then permitted to dry for 24 hours at 40C. Hardwar

7、e shall then be examined for evidence of corrosion, pitting, and ease of coupling. Durability: Applicable. Insulation resistance: Not applicable. Part or Identifying Number (PIN): 88065ZBS. Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as

8、they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 88065ZBS 00795 24931 64639 2032000A000-000 30PC104-1 290-900-02 1/ Parts must

9、be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Vender CAGE Vendor name number and address 00795 Delta Electronics 416 Cabot Street Be

10、verly, MA 01985 24931 Specialty Connector 2100 Earlywood Drive Franklin, IN 46131 64639 Micro-Coax Incorporated Box E 245 West 5thAvenue Collegeville, PA 19426 037Z3 88065 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REVB PAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-