DLA DSCC-DWG-88032 REV C-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE RM0502《固定的薄膜片状0欧姆0502RM型电阻器》.pdf

《DLA DSCC-DWG-88032 REV C-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE RM0502《固定的薄膜片状0欧姆0502RM型电阻器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-88032 REV C-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE RM0502《固定的薄膜片状0欧姆0502RM型电阻器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Revise section 4; Editorial changes throughout. 2 Mar 92 D. Moore B Add new source of supply; delete Group B requirement; update to present DoD policy requirements. 20 JUL 2000 Kendall A. Cottongim C Inactive for new design. Revise to present DoD policy req

2、uirements. 12 Apr 05 Kendall A. Cottongim CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Notice of Inactivation for New Design DSCC Drawing 88032 is inactive for new design and is no longer used, except for replacement purpo

3、ses. Use MIL-PRF-32159/1 Prepared in accordance with ASME Y14.100 Selected item drawing REV C C B C C REV STATUS OF PAGES PAGES 1 2 3 4 5 PMIC N/A PREPARED BY Allan R. Knox DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH CHECKED BY David W. Withrow APPROVED BY David E. Moore TITLE RESISTOR, CHIP, FIXED

4、, FILM, ZERO-OHM, STYLE RM0502 SIZE A CODE IDENT. NO. 14933 DWG NO. 88032 Original date of drawing 22 April 88 REV C PAGE 1 OF 5 AMSC N/A 5905-E512 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A C

5、ODE IDENT NO. 14933 DWG NO. 88032 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a resistor, fixed, film, zero-ohm, chip, .050 X .020. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 88032 I I Drawing number2. APPLICABLE DOCUMENTS 2.1 Government do

6、cuments. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENS

7、E SPECIFICATIONS MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-790 - Standard Practice for Established Reliability and High Reliability Qualified Products List (QPL) S

8、ystems for Electrical, Electronic, and Fiber Optics Parts Specifications. MIL-STD-1285 - Marking of Electrical, and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk

9、, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regula

10、tions unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55342 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as spec

11、ified in MIL-PRF-55342 and herein (see figure 1). 3.2.1 Design documentation. The design documentation shall be in accordance with MIL-PRF-55342 and unless otherwise specified in the contract or purchase order, shall be retained by the manufacturer and available for review by the acquiring activity

12、or contractor upon request. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88032 REV C PAGE 3 A B C D E 0.055 0.006 .025 .005 .010/.033 .010 .005 .015 .005 NOTES: 1. D

13、imensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. The pictorial view of the style above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are cont

14、ained within the envelope, and do not alter the functional aspects of the devices are acceptable. FIGURE 1. Zero-ohm chip resistor style RM0502. Inches .005 .006 .010 .015 .025 .033 .055 mm 0.13 0.15 0.25 0.38 0.64 0.84 1.40 Provided by IHSNot for ResaleNo reproduction or networking permitted withou

15、t license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88032 REV C PAGE 4 3.3 Electrical characteristics. 3.3.1 Temperature range. The temperature range shall be -55C to +150C. 3.3.2 Resistance. The resistance shall not exceed 0.02 ohm. 3.3.3 Termina

16、tion. Termination material shall be in accordance with MIL-PRF-55342, code letter B. 3.4 Marking. Marking of the individual chip resistors is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers

17、name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the opera

18、tional and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.7 Workmanship. Resistors shall be uniform in quality and free

19、 from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-55342 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Qualification inspection. Qualification in

20、spection is not applicable to this document. 4.3 Product level qualification. The product level qualification in specified with MIL-PRF-55342 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of

21、group A inspection (established reliability level only and the parts per million reporting is not applicable) of MIL-PRF-55342. 4.5 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in

22、accordance with the applicable requirements of MIL-PRF-55342. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these person

23、nel need to contact the responsible packaging activity to ascertain requisite requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the Military Services System Command. Packaging data retriev

24、al is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 In

25、tended use. Chip resistors are intended for use in thick or thin film circuits where microcircuitry is intended, also in most surface mount application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery and one cop

26、y of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

27、,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88032 REV C PAGE 5 6.3 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a

28、 recorded user of this drawing may be achieved online at Resistordla.mil or in writing to: DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.4 Suggested sources of supply. Approved sources of supply are listed herein. Additional sources will

29、be added as they become available. Assistance in the use of this drawing may be obtained online at Resistordla.mil or contact DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN Vendors similar designation or type number 1/ Vendo

30、r CAGE Vendors name and address 88032 H0502CPX000(DEC032)56235 State of the Art, Incorporated 2470 Fox Hill Road State College, PA 16803-1797 88032 WAJ81PS/NS62 50316 MINI-SYSTEMS, INC. 20 David Road N. Attleboro, MA 02761-0069 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-