DLA DSCC-DWG-87025 REV G-2013 RESISTOR NETWORK 8 PIN DUAL-IN-LINE PACKAGE (DIP).pdf

《DLA DSCC-DWG-87025 REV G-2013 RESISTOR NETWORK 8 PIN DUAL-IN-LINE PACKAGE (DIP).pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-87025 REV G-2013 RESISTOR NETWORK 8 PIN DUAL-IN-LINE PACKAGE (DIP).pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new vendor. 21 JUL 88 David E. Moore B Change vendors name. 31 AUG 89 David E. Moore C Add new vendors. Make editorial and dimensional corrections. 14 DEC 90 David E. Moore D Changes in accordance with NOR 5905-R017-93. 22 OCT 93 Andrew R. Ernst E Chang

2、es to power conditioning and operating voltage. Editorial changes throughout. 9 DEC 99 Kendall Cottongim F Add Group B inspection certification paragraph. Editorial changes throughout. 16 MAY 05 Kendall Cottongim G Add pure tin prohibition, manufacturers eligibility, and high pulse application parag

3、raphs. Editorial changes throughout. 21 March 13 Michael Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV G G G G G G G PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Allan R. Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing 14

4、 July 1987 CHECKED BY David E. Moore TITLE RESISTOR NETWORK, 8 PIN, DUAL-IN-LINE PACKAGE (DIP) APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 87025 REV G PAGE 1 OF 7 AMSC N/A 5905-2013-E10 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS,

5、OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87025 REV G PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for an 8 pin, resistor ne

6、twork. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 87025 - A K XXXX X I I I I I I I I I I Drawing number Schematic Characteristic Resistance Tolerance (1.2.1) (1.2.2) (1.2.3 and 3.3.6) (1.2.4 and 3.3.1) 1.2.1 Schematics. The schematic of the resistor network is identified b

7、y a single letter in accordance with the drawings (see figure 1). The resistor element RREFis the reference resistor element used in determining the ratio accuracy (when applicable). 1.2.2 Characteristics. The characteristic is identified by a single letter and is in accordance with MIL-PRF-83401. 1

8、.2.3 Resistance value designations. The resistance value designations are in accordance with MIL-PRF-83401. Resistance value designations for the schematic J are as specified in table I. TABLE I. Standard resistance values. Resistance designator R1(ohms) R2(ohms) Resistance Designator R1(ohms) R2(oh

9、ms) A001 A002 A003 A004 A005 A006 A007 82 120 130 160 180 180 220 130 200 210 260 240 390 270 A008 A009 A010 A011 A012 A013 220 330 330 330 1.5 k 3.0 k 330 390 470 680 3.3 k 6.2 k 1.2.4 Resistance tolerance. For available resistance tolerances and designators, see 3.3.1. 2. APPLICABLE DOCUMENTS * 2.

10、1 General. The documents listed in this section are specified in sections 3, 4 or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the co

11、mpleteness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3, 4 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, stand

12、ards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Netw

13、orks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. * (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the DLA Document Service Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) Provided by IHSNot for Resa

14、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87025 REV G PAGE 3 FIGURE 1. Resistor schematics. * 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a co

15、nflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual ite

16、m requirements shall be in accordance with MIL-PRF-83401 and as specified herein. * 3.2 Interface and physical dimensions. Resistors shall meet the interface and physical dimensions as specified in MIL-PRF-83401 and herein (see figure 2). Provided by IHSNot for ResaleNo reproduction or networking pe

17、rmitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87025 REV G PAGE 4 Inches .003 .004 .010 .012 .018 .020 mm 0.08 0.10 0.25 0.30 0.46 0.51 Inches .030 .032 .035 .040 .065 .070 mm 0.76 0.81 0.89 1.02 1.65 1.78 Inches .080 .085 .09 .

18、11 .120 .200 mm 2.03 2.16 2.3 2.8 3.05 5.08 Inches .270 .300 .310 .350 .420 mm 6.86 7.62 7.87 8.89 10.67 NOTES: 1. Dimensions are given in inches. 2. Metric equivalents are given for general information only. 3. Pin 1 locator shall be a dot, or a notch in the shaded area. 4. Side brazed configuratio

19、n optional. FIGURE 2. Resistor network. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87025 REV G PAGE 5 3.3 Electrical characteristics. 3.3.1 Resistance tolerance. R

20、esistors are available in B (0.1 percent), D (0.5 percent), F (1 percent), G (2 percent), and J (5 percent) tolerances. 3.3.2 Power rating. The power rating per schematics “A”, “B”, and “J” shall be as follows: Schematic A Characteristics C, R, V, and Y Characteristics H, K, and M Schematic B Charac

21、teristics C, R, V, and Y Characteristics H, K, and M Schematic J Characteristics C and V Characteristics H, K, and M Element power rating (watts) 0.1 0.2 0.05 0.1 0.025 0.050 Network power rating (watts) 0.4 0.8 0.35 0.7 0.3 0.6 3.3.3 Temperature range. The operating temperature range shall be -55C

22、to +125C. 3.3.4 Resistance temperature characteristic. The resistance temperature characteristic shall be in accordance with MIL-PRF-83401. 3.3.5 TC tracking. The TC tracking shall be 5 ppm/C. 3.3.6 Resistance. The resistance values shall be 10 ohms to 1 megohm. 3.3.7 Operating voltage. The maximum

23、operating voltage shall be 54 V dc for schematic A, 22 V dc for schematic B, and 100 V dc for schematic J. 3.4 Marking. Resistors shall be marked with the PIN assigned herein (see 1.2) and manufacturers identification code (CAGE or logo). Pin 1 indicator shall be located adjacent to pin 1. * 3.5 Pur

24、e tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.6 Recycled, recovered, or enviro

25、nmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the materials meet or exceed the operational and maintenance requirements, and promote economically advantageous life cycle costs. * 3.7 Manufactur

26、er eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-83401 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and

27、Maritime-VAT. * 3.7.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply. 3.8 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and free from defects that will affect

28、 life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection in accordance with MIL-PRF-83401 is not applicable to this document. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPL

29、Y CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87025 REV G PAGE 6 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A (M level part) and group B inspections of MIL-PRF-83401. 4.2.2 Certification. The acquiring a

30、ctivity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2c). 4.2.3 Power conditioning. The power conditioning shall be performed at rated power. 4.3 Schematic J tests. For the tests on schematic J, the dc resistance meas

31、urements, resistance temperature characteristics measurement, and short time overload power application shall be made between each terminal and the application common terminal without compensation for the shunt circuits. The pin to pin dc resistance measurement shall be used directly to determine th

32、e acceptability to section 3 requirements. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact

33、 the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available fr

34、om the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Resis

35、tor networks are intended to be used in electronic circuit where miniaturization is required. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or a certificate of compl

36、iance that parts have passed conformance inspection with each shipment of parts by the manufacturer. * c. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements (see 4.2.2). d. Requirements for packaging and packing. * 6.3 Electrostatic

37、charge. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 that spe

38、cifies a preventive packaging procedure. * 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operat

39、ing conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to

40、 ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87025 REV G PAGE 7 * 6.5 Pulse applications. D

41、esigners are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. These resistors only see a onetime pulse (Short-time overload) as part of the group B inspection of MI

42、L-PRF-83401. * 6.6 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: D

43、LA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.7 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be

44、 obtained online at resistordla.mil or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DLA Land and Maritime Drawing PIN Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address 87025-AXXXXXX c

45、haracteristics: H, K, M, R, V, Y res. values: 10 to 400k ohms all tolerances 87025-BXXXXXX characteristics: H, K, M, R, V, Y res. values: 10 to 200k ohms all tolerances 1959-XX-XXXXX 1954-XX-XXXXX 57027 International Resistive Company 4222 South Staples Street Corpus Christi, TX 78411-2796 87025-AXX

46、XXXX characteristics: C, R, V res. values: 100 to 499k ohms all tolerances 87025-BXXXXXX characteristics: C, R, V res. values: 100 to 499k ohms all tolerances 103 455 57489 Vishay Thin Film 2160 Liberty Drive Niagara Falls, NY 14304 87025-AXXXXXX characteristics: C, R, V res. values: 10 to 33k ohms

47、all tolerances 87025-AYXXXXX res. values: 300 to 33k ohms all tolerances 87025-BXXXXXX characteristics: C, R, V res. values: 25 to 10k ohms all tolerances 87025-BYXXXXX res. values: 300 to 10k ohms all tolerances 1440 S8016 Vishay Precision Group, Inc. 3 Great Valley parkway Suite 150 Malvern, PA 19

48、355-1417 Plant: Vishay Advanced Technologies, LTD 2 Haofan Street Holon 58814, Israel 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-