DLA DSCC-DWG-86105 REV B-2002 JUMPER PIN INSULATED《绝缘带弹返安全器的针》.pdf

《DLA DSCC-DWG-86105 REV B-2002 JUMPER PIN INSULATED《绝缘带弹返安全器的针》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-86105 REV B-2002 JUMPER PIN INSULATED《绝缘带弹返安全器的针》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update marking requirements 04/27/89 R. Marbias B Changed CAGE 14933 to 037Z3. Change tin plating to tin-lead. Change gold specification to ASTM B488. Type 2 designator removed. Editorial changes throughout. 05/30/02 R. HeberPrepared in accordance with ASME

2、Y14.100 REV PAGE REV B B B B REV STATUS OF PAGES PAGE 1 2 3 4 PREPARED BY PMIC N/A R. Taylor DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Richard Marbais JUMPER PIN, INSULATED SIZE CAGE CODE 037Z3 DWG. NO. 86105 Original date of drawing 18

3、 May 1987 A REV B PAGE 1 OF 4 AMSC N/A 5935-E692 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86105 DEFENSE SUPPLY CENTER, COLUMBUS COLU

4、MBUS, OH 43216-5000 A REV B PAGE 2 Type designations. Dimensions (see note 3) Type A B C 1 .090 .100 .145 Inches mm Inches mm .002 .005 .010 .018 .090 0.15 0.13 0.25 0.46 2.29 .100 .124 .275 .300 .400 2.54 3.15 6.99 7.62 10.16 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for g

5、eneral information only. 3. Unless otherwise specified all tolerances are .010 (0.25 mm). FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86105 DEFENSE SUPPLY CENTER, COLUMBUS COLUM

6、BUS, OH 43216-5000 A REV B PAGE 3 REQUIREMENTS: Design and configuration: Dimensions and configuration: See figure 1. Temperature range: -65C to +125C. Operating voltage: 500 V rms at atmospheric pressure. Current rating: 3 amperes dc. Materials: Insulator: Glass fiber reinforced polyterephthalate t

7、hermoplastic. Pin: Phosphor bronze, hard, in accordance with ASTM B139. Plating: Gold in accordance with ASTM B488 type 2, code C, class 0.75, over 50 (30 microinches) minimum microinches nickel. Tin-lead, 200 microinches (5.08 m) minimum, shall be in accordance with SAE-AMS-P-81728. Bulk resistance

8、: 10 milliohms at .020 ampere dc. Insulation resistance: 2,000 megohms at 90 percent relatively humidity. Solderability: In accordance with EIA 364-52, category 1, class 2. Dielectric withstanding voltage: 2,500 V rms for 5 seconds. TABLE I. Contact plating. Plating designator Plating material A Gol

9、d/nickel B Tin-lead Marking: The Part or Identifying Number (PIN) shall be marked on the housing and package in accordance with MIL-STD-1285. If size, surface condition, or other design considerations dont allow for full marking on the part, marking on the package is only required. The PIN shall inc

10、lude the complete DSCC PIN, manufacturers name or CAGE code, and date code. The marking shall be permanent and legible in accordance with method 215 of MIL-STD-202. The PIN shall be constructed using the following format: Part or Identifying Number (PIN): Example: 86105- X X Drawing Pin length Plati

11、ng number (see figure 1) (see table I) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86105 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 4 Replacement parts: For replacement purposes, the Governme

12、nt will stock, store and issue parts 86105-1A only. Approved source of supply. An approved source of supply is listed herein. Additional sources will be added as they become available. The vendor listed on the requirements drawing has agreed to this drawing and a certificate of compliance has been s

13、ubmitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ 2/ 86105-1A 00779 1437507-7 86105-1B 00779 1437507-9 1/ Do not use this number for acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Jumper has not been subjected to solderability test and is not recommended for solder applications. Vendor CAGE Vendor name number and address 00779 Tyco Electronics- AMP 2800 Fulling Mill Road Middletown, PA 17057-3163 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-