DLA DSCC-DWG-86102 REV J-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW RIGHT ANGLE.pdf

《DLA DSCC-DWG-86102 REV J-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW RIGHT ANGLE.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-86102 REV J-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW RIGHT ANGLE.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Add tolerance note and vendor CAGE OAKZ5. 10/19/87 Richard Marbais B Change marking requirement. Change current rating. Add caution note. Change title on Table III. 11/22/88 Richard Marbais C Figure 1and table I, made dimensional changes. Table III, added op

2、tions up to 80 positions. 06/01/90 Richard Marbais D Figure 1, change .050 to a ref dimension. Add resistance to soldering heat test and add temperature range designator table (Table IV). Add new designator to part number table. Change CAGE 22526 address. 10/03/92 Randy Larson E Add contact finish d

3、esignator C, table I define contact and termination area. Change CAGE 22529 to 8N187 and 95238 address. 03/29/95 Randy Larson F Change CAGE 14933 to 037Z3. Added solderless wrappost geometry requirements. Updated material callout. Editorial changes throughout. 04/18/02 Robert Heber G Updating refere

4、nces and CAGE (8N187) PINs. Editorial changes throughout. 17 May 2010 Abdo Abdouni H Update vendor CAGE OAKZ5 name and address. Editorial changes throughout. 6 June 2011 Howard Jenkins J Add option for selective plating to plating code “A”. 17 October 2012 Abdo Abdouni Prepared in accordance with AS

5、ME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV J H J H J H H H H PAGE 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Gail Willis Original date of drawing 8 Nov 1986 CHECKED BY TITLE Carl Dello-Stritto CONNECTORS, ELECTRICAL, UNSHR

6、OUDED HEADERS, PWB TERMINATION, .025, DOUBLE ROW, RIGHT ANGLE APPROVED BY Richard Marbais SIZE CAGE CODE DWG. NO. 86102 A 037Z3 REV J PAGE 1 OF 9 AMSC N/A 5935-E845-003 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot fo

7、r ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV H PAGE 2 Inches mm .008 .010 .015 .050 .060 .100 0.20 0.25 0.38 1.27 1.52 2.54 NOTES: 1. Dimensions are in inches. 2. Metric e

8、quivalents are given for information only. 3. Unless otherwise specified all tolerances are .005 (0.13 mm). 4. All dimensioned pictorial representations are for reference purposes only. 5. Plating transition area, contact finish “D” only. FIGURE 1. Dimensions and configuration.Provided by IHSNot for

9、 ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV J PAGE 3 TABLE I. Pin length. 1/ 2/ Dash number A Contact area B Termination Area C D Ref 01 02 03 04 05 06 07 08 09 10 11 12 1

10、3 14 15 16 17 18 19 .138 .230 .230 .230 .230 .230 .230 .230 .230 .230 .275 .318 .318 .318 .318 .345 .380 .400 .540 (3.51) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (6.99) (8.08) (8.08) (8.08) (8.08) (8.76) (9.65) (10.16) (13.72) .138 .039 .090 .095 .095 .110 .120 .125 .150 .195

11、.120 .110 .110 .125 .150 .110 .110 .120 .260 (3.51) (0.99) (2.29) (2.41) (2.41) (2.79) (3.05) (3.18) (3.81) (4.95) (3.05) (2.79) (2.79) (3.18) (3.81) (2.79) (2.79) (3.05) (6.60) .045 .045 .045 .045 .070 .070 .045 .045 .070 .045 .045 .045 .070 .045 .070 .070 .070 .045 .045 (1.14) (1.14) (1.14) (1.14)

12、 (1.78) (1.78) (1.14) (1.14) (1.78) (1.14) (1.14) (1.14) (1.78) (1.14) (1.78) (1.78) (1.78) (1.14) (1.14) .190 .190 .190 .190 .240 .240 .190 .190 .240 .190 .190 .190 .240 .190 .240 .240 .240 .190 .190 (4.83) (4.83) (4.83) (4.83) (6.10) (6.10) (4.83) (4.83) (6.10) (4.83) (4.83) (4.83) (6.10) (4.83) (

13、6.10) (6.10) (6.10) (4.83) (4.83) 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. TABLE II. Contact finishes. Plating Contact area “A” Termination area “B” A 1/ Gold Gold B Tin-lead plated Tin-lead plated C 1/ .200 inch (5.08 mm) gold Tin-lead plated D Gold Solder

14、dipped E Tin-lead plated Solder dipped F 1/ .200 inch (5.08 mm) gold Solder dipped 1/ Selective gold plating applicable to contact pin lengths .230 inch (5.84 mm) and longer. Measured from tip of contact pin, remainder of contact post to be plated with nickel in accordance with SAE-AMS-QQ-N-290, cla

15、ss 2, 50 microinch (1.27 m) minimum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV H PAGE 4 TABLE III. Dimensions E length. 1/ 2/ Number of positions D

16、imensions Number of positions Dimensions 02 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 .100 .200 .300 .400 .500 .600 .700 .800 .900 1.000 1.100 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000 (2.54) (5.08) (7.62) (10.16) (12.70) (15.24) (17.78) (20.32) (22.86) (25.40) (27.94) (30

17、.48) (33.02) (35.56) (38.10) (40.64) (43.18) (45.72) (48.26) (50.80) 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 2.100 2.200 2.300 2.400 2.500 2.600 2.700 2.800 2.900 3.000 3.100 3.200 3.300 3.400 3.500 3.600 3.700 3.800 3.900 4.000 (53.34) (55.88) (58.42) (60.96) (63.50) (66.04) (68

18、.58) (71.12) (73.66) (76.20) (78.74) (81.28) (83.82) (86.36) (88.90) (91.44) (93.98) (96.52) (99.06) (101.60) 1/ Dimensions are in inches. 2/ Metric equivalents are given for information. TABLE IV. Temperature range. PIN designator Temperature range C Blank -40 to +105 M -55 to +125 H -65 to +220 Pr

19、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV J PAGE 5 REQUIREMENTS: Shall meet the requirements of drawing 86100. Dimensions and configuration: See figu

20、res1, 3 and tables I, II, III. Temperature range: See table IV. Dielectric withstanding voltage: 1,000 volts rms (sea level). Current rating: 3 amperes continuous to 5 amperes maximum. Insulation resistance: 5,000 megohms. Resistance to soldering heat: Only applicable for “H” temperature range (see

21、table IV). Materials: Insulator: The insulator shall be one of the following types of plastic. All plastic material shall be rated V-0 in accordance with UL-94. a. Glass-or mineral-filled nylon in accordance with ASTM D4066. b. Glass filled thermoplastic in accordance with ASTM D5927 or MIL-M-24519.

22、 c. Thermoplastic polyphenylene sulfide type GST-40F in accordance with ASTM D4067. Contact: Three-fourth hard phosphor bronze in accordance with ASTM B139/B139M. Contact plating: Contact and termination plating shall be gold in accordance with ASTM B488, type 3, code C, class 1.27 (50 microinches),

23、 or 100 microinches (2.54m) minimum tin-lead in accordance with SAE AMS-P-81728 over 50 microinches (1.27 m) minimum nickel in accordance with SAE-AMS-QQ-N-290, class 2. The “D” or “E” lead finish shall be hot solder dipped with SN60 or SN63 solder in accordance with J-STD-006 to meet the solderabil

24、ity requirements of MIL-STD-202, method 208. Solderless wrappost geometry: The solderless wrappost geometry shall be in accordance with figures 2 and 3. Interface: See drawings 86038, 86103, 92025, 92026, 92027, and 92028. Printed wiring board (PWB) hole size: .040 .003 inch (1.02 0.08 mm). Provided

25、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV H PAGE 6 Number of wrapped connections E length Wire gage 30 (mm) Wire gage 28 (mm) Wire gage 26 (mm) Wire gage 2

26、4 (mm) Wire gage 22 (mm) Wire gage 20 (mm) Wire gage 18 (mm) 1 .185 (4.70) .219 (5.56) .226 (5.74) .258 (6.55) .303 (7.70) .327 (8.31) .391 (9.93) 2 .320 (8.13) .388 (9.86) .402 (10.21) .466 (11.84) .556 (14.12) .604 (15.34) .732 (18.59) 3 .455 (11.56) .557 (14.15) .578 (14.68) .674 (17.12) .809 (20

27、.55) .881 (22.37) 1.073 (27.25) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 2. Wrappable length (typical connection). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS

28、 COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV H PAGE 7 Inches mm .0012 .0015 .003 0.030 0.038 0.076 A (mm) B (mm) C (mm) Parallelism (mm) Straightness Inch/inch (mm) .025 (0.64) nominal .022 (0.56) min .025 (0.64) nominal .022 (0.56) min .0355 (0.902) max .0325 (0.826) min .002 (

29、0.05) .005 (0.13) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 3. Wrappost geometry.BURR .0015 MAX.003 R MAXBCC.0012 MAXIMUM PERMISSIBLEDIVIATION FROM SQUARE ORRECTANGLEAProvided by IHSNot for ResaleNo reproduction or networking permitted without l

30、icense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV H PAGE 8 Marking: The Part or Identifying Number (PIN) shall be marked on the package in accordance with MIL-STD-1285. The PIN shall include the complete DSCC PIN, manufacturers name

31、or CAGE code, and date code. The marking shall be permanent and legible in accordance with method 215 of MIL-STD-202. The PIN shall be constructed using the following format: 86102 -XX -X -YY Z Drawing Pin length Plating 1/ Number of positions Temperature range number (see table I) (see table II) (s

32、ee table III) (see table IV) 1/ Plating designator “C”, selective plating, is not suitable for wire wrap applications. Approved source of supply: An approved source of supply is listed herein. Additional sources will be added as they become available. The vendor listed on the requirements drawing ha

33、s agreed to this drawing and a certificate of compliance has been submitted to DLA land and Maritime-VAI. DSCC drawing PIN Vendor CAGE number 8N187 1/ 2/ OAKZ5 1/ 3/ 95238 1/ 86102-01-X-YYZ 86102-02-X-YYZ 86102-03-X-YYZ 86102-04-X-YYZ 86102-05-X-YYZ 86102-06-X-YYZ 86102-07-X-YYZ 86102-08-X-YYZ 86102

34、-09-X-YYZ 86102-10-X-YYZ 86102-11-X-YYZ 86102-12-X-YYZ 86102-13-X-YYZ 86102-14-X-YYZ 86102-15-X-YYZ 86102-16-X-YYZ 86102-17-X-YYZ 86102-18-X-YYZ 86102-19-X-YYZ 68715-XYYLF-MIL 68780-XYYLF-MIL 68695-XYYLF-MIL 68020-XYYLF-MIL 68405-XYYLF-MIL 68463-XYYLF-MIL 68021-XYYLF-MIL 68697-XYYLF-MIL 68492-XYYLF-

35、MIL 68025-XYYLF-MIL 68759-XYYLF-MIL 68480-XYYLF-MIL 68022-XYYLF-MIL 68696-XYYLF-MIL 68459-XYYLF-MIL 68740-XYYLF-MIL 68452-XYYLF-MIL 68462-XYYLF-MIL 68147-XYYLF-MIL SPEG102Z-01-XYY-MIL SPEG102Z-02-XYY-MIL SPEG102Z-03-XYY-MIL SPEG102Z-04-XYY-MIL SPEG102Z-05-XYY-MIL SPEG102Z-06-XYY-MIL SPEG102Z-07-XYY-

36、MIL SPEG102Z-08-XYY-MIL SPEG102Z-09-XYY-MIL SPEG102Z-10-XYY-MIL SPEG102Z-11-XYY-MIL SPEG102Z-12-XYY-MIL SPEG102Z-13-XYY-MIL SPEG102Z-14-XYY-MIL SPEG102Z-15-XYY-MIL SPEG102Z-16-XYY-MIL SPEG102Z-17-XYY-MIL SPEG102Z-18-XYY-MIL SPEG102Z-19-XYY-MIL H211-YY-901-XZ H211-YY-902-XZ H211-YY-903-XZ H211-YY-904

37、-XZ H211-YY-905-XZ H211-YY-906-XZ H211-YY-907-XZ H211-YY-908-XZ H211-YY-909-XZ H211-YY-910-XZ H211-YY-911-XZ H211-YY-912-XZ H211-YY-913-XZ H211-YY-914-XZ H211-YY-915-XZ H211-YY-916-XZ H211-YY-917-XZ H211-YY-918-XZ H211-YY-919-XZ 1/ Parts must be purchased to this DSCC PIN to assure that all performa

38、nce requirements and tests are met. 2/ Vendor PIN covers “Blank” and “M” temperature ranges only (see table IV). 3/ Vendor PIN applicable to “Blank” temperature range only (see table IV). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY

39、 CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86102 REV H PAGE 9 Vendor CAGE Vendor name number and address OAKZ5 Muller-Crane 1280 Massillon Road Building G Suite 1500n Akron, OH 44306 8N187 T.T.I 2601 Sylvania Cross Dr. Fort Worth, TX 76137 95238 Continental Connector Company 2294 North Penn Road Hatfield, PA 19440 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-