DLA DSCC-DWG-09019 REV A-2012 CAPACITORS FIXED GLASS DIELECTRIC (AXIAL WIRE-LEAD TERMINALS).pdf

《DLA DSCC-DWG-09019 REV A-2012 CAPACITORS FIXED GLASS DIELECTRIC (AXIAL WIRE-LEAD TERMINALS).pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-09019 REV A-2012 CAPACITORS FIXED GLASS DIELECTRIC (AXIAL WIRE-LEAD TERMINALS).pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LT DESCRIPTION DATE APPROVED A Added a 10% tolerance option. 14 March 2012 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS REV A A A A A A A OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY John Bonitatibus DESIGN ACTIVITY DEFENSE SUPPLY CENT

2、ER, COLUMBUS COLUMBUS, OH Original date of drawing 11 May 2010 CHECKED BY Patrick G. Kyne TITLE CAPACITORS, FIXED, GLASS DIELECTRIC, (AXIAL WIRE-LEAD TERMINALS) APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09019 SCALE N/A REV A PAGE 1 OF 7 AMSC N/A 5910-2012-E05CURRENT DESIGN

3、ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09019 REV A PAGE 2 1. SC

4、OPE 1.1 Scope. This drawing describes the requirements for glass dielectric capacitors screened to MIL-PRF-23269. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 09019 -001 Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed

5、in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document

6、users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a par

7、t of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-23269 - Capacitors, Fixed, Glass Dielectric, Established Reliability, General Specification for.

8、(Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a confl

9、ict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.

10、1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-23269 and herein (see figure 1 and table I). 3.1.1 Case material. Glass. 3.1.2 Terminals. Solderable. 3.1.3 Seal. Hermetic. 3.1.4 Pure tin. The use of pure tin, as an underplate or final finis

11、h is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. Provided by IHSNot for ResaleNo reproduction or network

12、ing permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09019 REV A PAGE 3 Inches mm Inches mm .001 0.03 .062 1.57 .004 0.10 .141 3.58 .025 0.64 .422 10.72 .031 0.79 .734 18.64 .047 1.19 1.125 28.58 NOTES: 1. Dimensions are in inc

13、hes. 2. Metric equivalents are given for general information only. 3. See marking requirement (see 3.8). FIGURE 1. Dimensions and configurations. 3.3 Electrical characteristics. 3.3.1 Capacitance tolerance. See table I. 3.3.2 Rated voltage. See table I. 3.3.3 Capacitance. When measured as specified

14、in MIL-PRF-23269, the capacitance shall be within the applicable tolerance of the nominal value specified in table I. 3.3.4 Dissipation factor. When measured as specified in MIL-PRF-23269, the dissipation factor shall not exceed 0.1 percent. 3.3.5 Temperature coefficient and capacitance drift (manuf

15、acturer eligibility only (see 3.9). When measured as specified in MIL-PRF-23269, the capacitors shall meet the following requirements: a. Temperature coefficient: 140 parts per million (ppm)/C 25 ppm/C. b. Capacitance drift: 0.1 percent or 0.1 pF, whichever is greater. 09019 -001 TM 09A Provided by

16、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09019 REV A PAGE 4 3.3.6 Insulation resistance (IR). When measured as specified in MIL-PRF-23269, the insulation resistance shall b

17、e 100,000 megohms, minimum, at +25C. 3.3.7 Quality factor (Q) (manufacturer eligibility only (see 3.9). In accordance with MIL-PRF-23269. 3.4 Seal. In accordance with MIL-PRF-23269, test I. 3.5 Thermal shock (manufacturer eligibility group C only (see 3.9). In accordance with MIL-PRF-23269. The foll

18、owing detail shall apply: Dissipation factor: 0.1 percent maximum. 3.6 Moisture resistance (manufacturer eligibility only (see 3.9). In accordance with MIL-PRF-23269. The following detail shall apply: Dissipation factor: 0.1 percent maximum. 3.7 Life (manufacturer eligibility only (see 3.9). In acco

19、rdance with MIL-PRF-23269. The following details shall apply: a. Capacitance (240 hours and 2,000 hours): 0.5 percent maximum. b. Dissipation factor (240 hours and 2,000 hours): 0.15 percent maximum. 3.8 Marking. In accordance with MIL-PRF-23269, except the capacitor shall be marked with the PIN as

20、specified herein (see 1.2. 09019 DSCC drawing number -001 Non-significant dash number TM 09A | Trademark Year Sequential 4 week lot code code 3.9 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-23269 Qualified Produc

21、ts Database for at least one part, or perform the group A and group C inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable

22、materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.11 Certificate of compliance. A certificate of compliance shall be required from manufacturers

23、requesting to be an approved source of supply. 3.12 Workmanship. The capacitor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspectio

24、n. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection of MIL-PRF-23269. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of mater

25、iel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Ag

26、ency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or netw

27、orking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09019 REV A PAGE 5 TABLE I. Electrical characteristics and dash numbers. Capacitance (pF) Capacitance tolerance Dash number DSCC Drawing 09019- 500 V dc 100 V dc 560 1% 00

28、1 101 560 2% 002 102 560 5% 003 103 560 10% 073 173 620 1% 004 104 620 2% 005 105 620 5% 006 106 620 10% 074 174 680 1% 007 107 680 2% 008 108 680 5% 009 109 680 10% 075 175 750 1% 010 110 750 2% 011 111 750 5% 012 112 750 10% 076 176 820 1% 013 113 820 2% 014 114 820 5% 015 115 820 10% 077 177 910

29、1% 016 116 910 2% 017 117 910 5% 018 118 910 10% 078 178 1,000 1% 019 119 1,000 2% 020 120 1,000 5% 021 121 1,000 10% 079 179 1,100 1% 022 122 1,100 2% 023 123 1,100 5% 024 124 1,100 10% 080 180 1,200 1% 025 125 1,200 2% 026 126 1,200 5% 027 127 1,200 10% 081 181 1,300 1% 028 128 1,300 2% 029 129 1,

30、300 5% 030 130 1,300 10% 082 182 1,500 1% 031 131 1,500 2% 032 132 1,500 5% 033 133 1,500 10% 083 183 1,600 1% 034 134 1,600 2% 035 135 1,600 5% 036 136 1,600 10% 084 184 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS

31、 COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09019 REV A PAGE 6 TABLE I. Electrical characteristics and dash numbers - Continued. Capacitance (pF) Capacitance tolerance Dash number DSCC Drawing 09019- 500 V dc 100 V dc 1,800 1% 037 137 1,800 2% 038 138 1,800 5% 039 139 1,800 10% 085 185 2,000

32、 1% 040 140 2,000 2% 041 141 2,000 5% 042 142 2,000 10% 086 186 2,200 1% 043 143 2,200 2% 044 144 2,200 5% 045 145 2,200 10% 087 187 2,400 1% 046 146 2,400 2% 047 147 2,400 5% 048 148 2,400 10% 088 188 2,700 1% 049 149 2,700 2% 050 150 2,700 5% 051 151 2,700 10% 089 189 3,000 1% 052 152 3,000 2% 053

33、 153 3,000 5% 054 154 3,000 10% 090 190 3,300 1% 055 155 3,300 2% 056 156 3,300 5% 057 157 3,300 10% 091 191 300Vdc 100 V dc 3,600 1% 058 158 3,600 2% 059 159 3,600 5% 060 160 3,600 10% 092 192 3,900 1% 061 161 3,900 2% 062 162 3,900 5% 063 163 3,900 10% 093 193 4,300 1% 064 164 4,300 2% 065 165 4,3

34、00 5% 066 166 4,300 10% 094 194 4,700 1% 067 167 4,700 2% 068 168 4,700 5% 069 169 4,700 10% 095 195 5,100 1% 070 170 5,100 2% 071 171 5,100 5% 072 172 5,100 10% 096 196 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS

35、COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09019 REV A PAGE 7 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications

36、do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification ex

37、ists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the c

38、onformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for notification of change of product to the acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Tin wh

39、isker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials.

40、Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposit

41、ed Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes fro

42、m the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal

43、 notations and relationship to the last previous issue. 6.6 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writi

44、ng to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. 6.7 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become av

45、ailable. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. Vendor Vendor CAGE Vendor name and address Similar designation 1/ A 16299 AVX Corporation FM20*079190 3900 Electronics Drive Raleigh, NC 27604-1698 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-