DLA DSCC-DWG-09016 REV A-2010 RESISTOR NETWORK FIXED FILM 27 PAD BALL GRID ARRAY.pdf

《DLA DSCC-DWG-09016 REV A-2010 RESISTOR NETWORK FIXED FILM 27 PAD BALL GRID ARRAY.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-09016 REV A-2010 RESISTOR NETWORK FIXED FILM 27 PAD BALL GRID ARRAY.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Resistance range increase, editorial comments throughout 21 Sept 10 M Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV A A A A A A A A PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Jesus V. Garcia III DEFENSE SUPP

2、LY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 Original date of drawing 17 December 2009 CHECKED BY Andrew R. Ernst TITLE RESISTOR NETWORK, FIXED FILM, 27 PAD, BALL GRID ARRAY APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09016 REV A PAGE 1 OF 8 AMSC N/A 5905-E753 CURRENT DESIGN A

3、CTIVITY CAGE CODE 037Z3 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09016 REV A PAGE 2 1. SCOPE 1.1 Scope. This dra

4、wing describes the requirements for a fixed, film, resistor network with 27 pad ball grid array. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 09016 - * * * Drawing number Resistance value designator (see 3.3.1) Resistance tolerance (see 3.3.3) Schematic (see 3.3.6) 2. APPLIC

5、ABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the cited in the solicitation

6、or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Specification for. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the

7、 Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Not

8、hing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55342 and as specified herein. 3.2 Interface and physical dimensions.

9、The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-55342 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO.

10、09016 REV A PAGE 3 mm Inch mm Inch mm Inch mm Inch 0.050 0.002 0.160 0.006 0.630 0.025 1.270 0.050 0.100 0.004 0.250 0.010 0.640 0.025 3.000 0.118 0.150 0.006 0.500 0.020 1.000 0.039 0.900 0.354 NOTES: 1. Dimensions are in Metric. Inches equivalents are given for general information only. 2. The pic

11、torial view of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable. 3. The bottom view shown above represents the mounting side

12、. FIGURE 1. Resistor network. 3.3 Electrical characteristics 3.3.1 Resistance. The four-digit resistance designation is applicable to all resistance tolerances. The nominal resistance is identified by four digits; the first three digits represent significant figures and the last digit specifies the

13、number of zeros to follow. When the value of resistance is less than 100 ohms, or when a fractional value of an ohm is required, the “R” will be substituted for one of the significant digits to represent the decimal point. When the letter “R” is used, succeeding digits of the group represent signifi

14、cant figures. The resistance values designations are shown in table I. Standard values for every decade will follow the sequence demonstrated for “10 to 100” decade in table II. Resistance values not listed in table II for the appropriate resistance tolerance will be considered as not conforming to

15、the specification TABLE I. Designation of resistance values for resistance Designation Resistance ohms 10R0 to 98R8 incl. 10.0 to 98.8 incl. 1000 to 9880 incl. 100 to 988 Incl. 1001 to 9881 incl. 1,000 to 9,880 incl. 1002 incl. 10,000 incl. 0.64 mm 0.05 diameter solder bumps 3.0 mm 0.15 mm 1.00 mm 0

16、.25 mm 0.63 mm 0.1 mm 1.00 mm 0.25 mm C B A 0.50 mm 0.25 mm 9.00 mm 0.15 mm 1.27 mm 0.16 mm Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09016 REV A PAGE 4 TABLE II

17、. Standard resistance values for the 10 to 100 decade. 1/ (B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J) 10.00 10.00 10.00 18.40 33.20 33.20 58.30 10.10 18.70 18.70 33.60 59.00 59.00 10.20 10.20 18.90 34.00 34.00 59.70 10.40 19.10 19.10 34.40 60.4

18、0 60.40 10.50 10.50 19.30 34.80 34.80 61.20 10.60 19.60 19.60 35.20 61.90 61.90 10.70 10.70 19.80 35.70 35.70 62.00 10.90 20.00 20.00 20.00 36.00 62.60 11.00 11.00 20.30 36.10 63.40 63.40 11.10 20.50 20.50 36.50 36.50 64.20 11.30 11.30 11.00 20.80 37.00 64.90 64.90 11.40 21.00 21.00 37.40 37.40 65.7

19、0 11.50 11.50 21.30 37.90 66.50 66.50 11.70 21.50 21.50 38.30 38.30 67.30 11.80 11.80 21.80 38.80 68.00 12.00 12.00 22.00 39.00 68.10 68.10 12.10 12.10 22.10 22.10 39.20 39.20 69.00 12.30 22.30 39.70 69.80 69.80 12.40 12.40 22.60 22.60 40.20 40.20 70.60 12.60 22.90 40.70 71.50 71.50 12.70 12.70 23.2

20、0 23.20 41.20 41.20 72.30 12.90 23.40 41.70 73.20 73.20 13.00 13.00 13.00 23.70 23.70 42.20 42.20 74.10 13.20 24.00 24.00 42.70 75.00 75.00 75.00 13.30 13.30 24.30 24.30 43.00 75.90 13.50 24.60 43.20 43.20 76.80 76.80 13.70 13.70 24.90 24.90 43.70 77.70 13.80 25.20 44.20 44.20 78.70 78.70 14.00 14.0

21、0 25.50 25.50 44.80 79.60 14.20 25.80 45.30 45.30 80.60 80.60 14.30 14.30 26.10 26.10 45.90 81.60 14.50 26.40 46.40 46.40 82.00 14.70 14.70 26.70 26.70 47.00 47.00 82.50 82.50 14.90 27.00 47.50 47.50 83.50 15.00 15.00 15.00 27.10 48.10 84.50 84.50 15.20 27.40 27.40 48.70 48.70 85.60 15.40 15.40 27.7

22、0 49.30 86.60 86.60 15.60 28.00 28.00 49.90 49.90 88.70 88.70 15.80 15.80 28.40 50.50 89.80 16.00 16.00 28.70 28.70 51.00 90.90 90.90 16.20 16.20 29.10 51.10 51.10 91.00 16.40 29.40 29.40 51.70 92.00 93.10 16.50 16.50 29.80 52.30 52.30 93.10 16.70 30.00 53.00 94.20 95.30 16.90 16.90 30.10 30.10 53.6

23、0 53.60 95.30 17.20 30.50 54.20 96.50 97.60 17.40 17.40 30.90 30.90 54.90 54.90 97.60 17.60 31.20 55.60 98.80 17.80 17.80 31.60 31.60 56.00 18.00 18.00 32.00 56.20 56.20 18.20 18.20 32.40 32.40 56.90 32.80 57.60 57.60 33.00 1/ Resistance values not listed in table II for the appropriate resistance t

24、olerance will be considered as not conforming to the specification. The resistance values for tolerances B, C, and D may be any value within the limits specified in 3.3.2, but it is preferred that values be chosen from “B”, “C” and “D” column of table II. Provided by IHSNot for ResaleNo reproduction

25、 or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09016 REV A PAGE 5 3.3.2 Resistance temperature characteristic. Unless otherwise specified, the resistance temperature characteristic shall be 100 ppm/OC. 3.3.3 Re

26、sistance tolerance. Networks are available in resistance tolerances as specified in table III. TABLE III Resistance tolerance. Symbol Resistance tolerance percent Available resistance range (in ohms) Schematic A Schematic B F 1.0 10 to 4.7K 10 to 2.2K G 2.0 J 5.0 10 to 10K 3.3.4 Resistor power ratin

27、g. The resistor power rating for individual resistors shall be 100 milliwatts (.1 Watt) maximum at 70OC derated to zero watts at 85OC. 3.3.5 Package power rating. The package power rating shall be 1,200 milliwatts (1.2 Watts) maximum at 70OC derated to zero watts at 85OC (see figure 2). FIGURE 2. De

28、rating curve. 3.3.6 Schematic. The schematics of the resistor network are identified by a single letter in accordance with figure 3. Schematic A Schematic B FIGURE 3. Schematic. 9 9 A B C 1 2 3 4 5 6 7 8 A B C 1 2 3 4 5 6 7 8 Percentofrated power-60 -40 -20 0 20 40 60 80 100 120 150 Temperature (OC)

29、 100 80 60 40 20 0 70OC -40OC 85OC Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09016 REV A PAGE 6 3.3.7 Pure tin. The use of pure tin, as an underplate or final fi

30、nish, is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.4 Thermal shock. When networks are tested as specified in MIL-PRF-55342, for thermal sho

31、ck the change in resistance shall not exceed 0.1 percent 0.01 ohm. 3.5 Low temperature operation. When networks are tested as specified in MIL-PRF-55342, for low temperature operation the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.6 Short time overload. When networks are tested a

32、s specified in MIL-PRF-55342, for short time overload the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.7 High temperature exposure. When networks are tested as specified in MIL-PRF-55342, for high temperature exposure the change in resistance shall not exceed 0.1 percent 0.01 ohm.

33、3.8 Resistance to soldering heat. When networks are tested as specified in MIL-PRF-55342, for resistance to soldering heat the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.9 Moisture resistance. When networks are tested as specified in MIL-PRF-55342, for moisture resistance the cha

34、nge in resistance shall not exceed 0.02 percent 0.01 ohm. 3.10 Resistance temperature characteristic. When networks are tested as specified in MIL-PRF-55342, the RTC shall not exceed the values specified (see 3.3.2). 3.11 Marking. Unit marking is not required on this resistor. Unit package shall be

35、marked with the PIN assigned herein (see 1.2), the manufacturers identification code, the date code, and the lot code. At the option of the manufacturer, the resistor may be marked (i.e., laser, color dot, etc.). The marking shall remain legible after all tests. 3.12 Manufacturer eligibility. To be

36、eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-55342 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.12.1 Certificate

37、 of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as approved sources of supply. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent

38、 possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. 3.14 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and be free from defects that will affect life, serv

39、iceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection in accordance with MIL-PRF-55342 is not applicable to this document. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COL

40、UMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09016 REV A PAGE 7 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A and B inspections of MIL-PRF-55342. 4.2.1.1 Group A inspection. Group A inspection shall be in acco

41、rdance with MIL-PRF-55342 with the following exceptions. 4.2.1.1.1 Visual Inspection. The visual inspection of Subgroup 1 is not required. 4.2.1.1.2 Solderability. The method for solderability test for Subgroup 4 shall be conducted per manufacturers standard practice. All terminations shall exhibit

42、a continuous solder coating free from defects for a minimum of 95 percent of the critical surface area of any individual termination. Anomalies other than dewetting, non-wetting, and pinholes are not cause for rejection. 4.2.1.2 Group B inspection. Group B inspection shall be in accordance with MIL-

43、PRF-55342. 4.2.1.2.1 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in th

44、e contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packagin

45、g activity within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.

46、6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the requir

47、ed function are not available for the OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery; One copy of the conformance inspection data or a certificate of compliance that parts have passed conformanc

48、e inspection with each shipment of parts by the manufacturer. c. Packaging requirements (see 5.1). (i.e. Electrostatic discharge sensitive packaging). d. Whether the manufacturer performs the group B tests or provides certificate of compliance with group B (see 4.2.1.2.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09016 REV A PAGE 8 6.3 Tin whisker gro