DLA DSCC-DWG-09009-2009 CAPACITOR FIXED TANTALUM CHIP MODULE LOW ESR.pdf

《DLA DSCC-DWG-09009-2009 CAPACITOR FIXED TANTALUM CHIP MODULE LOW ESR.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-09009-2009 CAPACITOR FIXED TANTALUM CHIP MODULE LOW ESR.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LT DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100-2000 Source control drawing REV STATUS OF PAGES REV PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Ken Bernier DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing CHECKED BY Patrick Kyne TITLE CAPACITOR,

2、 FIXED, TANTALUM CHIP MODULE, LOW ESR APPROVED BY Michael A. Radecki 30 July 2009 SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09009 REV PAGE 1 OF 7 AMSC N/A 5910-E425 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, CO

3、LUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09009 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the complete requirements for low ESR tantalum chip capacitor modules assembled from individual CWR29 capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as f

4、ollows: 09009 01K B C A Drawing number Dash number Capacitance Reliability Grade Termination finish Surge Current (see table I) tolerance B = B Weibull B = Gold plated option K = 10 percent C = C Weibull (10 microinch minimum) A, B, or C M = 20 percent D = D Weibull C = Hot solder dip per (60 microi

5、nch minimum) MIL-PRF-55365 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are

6、 those cited in the solicitation or contract.). SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-55365 - Capacitor, Fixed, Electrolytic (Tantalum), Chip, Established Reliability, Nonestablished Reliability, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-202 - Test Method Standard, Ele

7、ctronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.mil/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philad

8、elphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has bee

9、n obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Terminations. Chip capacitors shall have gold plated or solder plated terminations (see 1.2 and figure 1). The solder plated terminations shall

10、be solderable when tested in accordance with MIL-STD-202, method 208. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is three percent. 3.1.2 Operating temperature range. The capacitors are rated for thei

11、r given voltages from -55C to +85C. They are derated two thirds of their given voltages at +125C. See table I. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09009 REV PAGE 3 Case code Length (L) Width (W) Height (H) Termination W

12、idth (W) Termination Length (P) 0.38 (0.015) 0.38 (0.015) 0.38 (0.015) 0.38 (0.015) For Reference Only 2H 7.82 (0.308) 4.06 (0.160) 6.10 (0.240) 4.06 (0.160) 1.52 (0.060) 4H 7.82 (0.308) 8.13 (0.320) 6.10 (0.240) 8.13 (0.320) 1.52 (0.060) 6H 7.82 (0.308) 8.13 (0.320) 9.14 (0.360) 8.13 (0.320) 1.52 (

13、0.060) NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are in parentheses and are given for information only. 3. The anode (+) terminal shall be indicated by a polarity stripe on the top surface at the anode end. 4. Solderable surfaces are only those surfaces designated as such. Termina

14、tion edges are not considered solderable. FIGURE 1. Dimensions and configuration. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09009 REV PAGE 4 TABLE I. Electrical characteristics. DSCC Drawing PIN 1/ 09009- Cap (nom) uF Rated V

15、oltage V dc DC Leakage (max) Dissipation Factor (max) ESR 100 kHz +25C Case Size +25C +85C +125C +25C +85/125C -55C A A A % % % m 01- 660 6 39.6 396 495 10 12 12 50 2H 02- 440 10 44 440 550 10 12 12 50 2H 03- 200 15 30 300 375 10 12 12 63 2H 04- 94 20 18.8 188 235 8 10 10 75 2H 05- 66 25 16.5 165 20

16、6 8 10 10 85 2H 06- 20 35 7 70 88 8 10 10 200 2H 07- 9.4 50 4.7 47 59 6 8 8 200 2H 08- 1320 6 79.2 792 990 10 12 12 25 4H 09- 880 10 88 880 1100 10 12 12 25 4H 10- 400 15 60 600 750 10 12 12 31 4H 11- 188 20 37.6 376 470 8 10 10 38 4H 12- 132 25 33 330 413 8 10 10 43 4H 13- 40 35 14 140 175 8 10 10

17、100 4H 14- 18.8 50 9.4 94 118 6 8 8 100 4H 15- 1980 6 118.8 1188 1485 10 12 12 17 6H 16- 1320 10 132 1320 1650 10 12 12 17 6H 17- 600 15 90 900 1125 10 12 12 21 6H 18- 282 20 56.4 564 705 8 10 10 25 6H 19- 198 25 49.5 495 619 8 10 10 28 6H 20- 60 35 21 210 263 8 10 10 67 6H 21- 28.2 50 14.1 141 176

18、6 8 8 67 6H 1/ Complete PIN shall include additional symbols to indicate capacitance tolerance (where applicable), reliability, termination finish, and surge current option. (see 1.2) 3.2 Electrical characteristics. 3.2.1 Capacitance. See table I. Measured in accordance with MIL-STD-202 method 305.

19、Maximum dc bias shall be 2.2 volts for all ac measurements. The frequency of the ac voltage shall be 120 5 Hz and the magnitude shall be limited to 1.0 volt rms. 3.2.2 Capacitance tolerance. K = 10 percent, M = 20 percent. 3.2.3 Rated voltage(see MIL-PRF-55365). . The rated voltage shall be in accor

20、dance with table I. Above +85C, voltage derating is required Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09009 REV PAGE 5 3.3 Surge current (Optional)Surge current shall be performed 100% basis before or after the group A (Weib

21、ull distribution) weibull FRL grading of MIL-PRF-55365. Surge current options are A, B, C or Z per MIL-PRF-55365. On completion of the test, the capacitors shall meet the following requirements: DCL: See table I. Cap.: Shall meet the initial measured value. DF: See table I. 3.4 Additional tests. The

22、 following additional tests shall be performed at the option of the user (see 6.2b) and shall be negotiable with the manufacturer. 3.4.1 Vibration, high frequency. The capacitors shall meet the requirements of MIL-PRF-55365 when tested in accordance with test condition D, of MIL-STD-202 method 204.

23、3.4.2 Thermal shock. Thermal shock shall be in accordance with MIL-PRF-55365 when tested for five cycles. 3.4.3 Solderability. Solderability shall be in accordance with MIL-PRF-55365. 3.4.4 Surge voltage. Surge voltage shall be in accordance with MIL-PRF-55365. 3.4.5 Moisture resistance. Moisture re

24、sistance shall be in accordance with MIL-PRF-55365. 3.4.6 Stability at low and high temperaturesMIL-PRF-55365. . Stability at low and high temperatures shall be in accordance with 3.4.7 Resistance to soldering heat. Resistance to soldering heat shall be in accordance with MIL-PRF-55365. 3.4.8 Life.

25、A minimum of dc rated voltage at 85C or a minimum of derated voltage at 125C for 2000 hours. 3.4.9 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-55365 Qualified Products Database for at least one part, or perform t

26、he group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided

27、that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a approved source of supply. 3.7 Marking. Marking

28、 shall be performed on the individual parts in accordance with MIL-PRF-55365, except the “JAN“ or “J“ brand symbol does not apply and shall not be marked on the capacitor or any packaging. 3.8 Workmanship. Capacitors shall be uniform in quality and free from defects that will affect life, serviceabi

29、lity, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the section 3.4 testing including the optional surge current test and

30、group A inspection (Weibull distribution Grade B or C) of MIL-PRF-55365 performed on each individual capacitor, and 100% electrical test (Capacitance, Dissipation Factor, DC Leakage and ESR) of each completed module. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SI

31、ZE A CODE IDENT NO. 037Z3 DWG NO. 09009 REV PAGE 6 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to

32、 contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is avai

33、lable from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualifi

34、ed military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product cov

35、ered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection da

36、ta or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions are coordinated only with the approved sources of supply a

37、nd the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdla.mil also by telephone (614) 692-0563 or DSN 850-0

38、563. Provided by IHSNot for Resale-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09009 REV PAGE 7 6.4 Similar vendor types. See table II. TABLE II. Similar vendor types (A). DSCC Drawing 09009- AVX part number 01- TC2H 667 *006L#D00+ 02- TC2H 447 *010L#D00+ 0

39、3- TC2H 207 *015L#D00+ 04- TC2H 946 *020L#D00+ 05- TC2H 666 *025L#D00+ 06- TC2H 206 *035L#D00+ 07- TC2H 945 *050L#D00+ 08- TC4H 138 *006L#D00+ 09- TC4H 887 *010L#D00+ 10- TC4H 407 *015L#D00+ 11- TC4H 197 *020L#D00+ 12- TC4H 137 *025L#D00+ 13- TC4H 406 *035L#D00+ 14- TC4H 196 *050L#D00+ 15- TC6H 208

40、*006L#D00+ 16- TC6H 138 *010L#D00+ 17- TC6H 607 *015L#D00+ 18- TC6H 287 *020L#D00+ 19- TC6H 207 *025L#D00+ 20- TC6H 606 *035L#D00+ 21- TC6H 286 *050L#D00+ 6.4 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assi

41、stance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdla.mil also by telephone (614) 692-0563 or DSN 850-0563. DSCC drawing PIN Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address 09009 A 17554 AVX Tantalum Corp. 401 Hill St. Biddeford, ME 04005 (207)282-5111 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for Resale-,-,-