DLA DSCC-DWG-07024 REV B-2013 RESISTORS CHIP FIXED BULK METAL FOIL ULTRA PRECISION STYLE 0805.pdf

《DLA DSCC-DWG-07024 REV B-2013 RESISTORS CHIP FIXED BULK METAL FOIL ULTRA PRECISION STYLE 0805.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-07024 REV B-2013 RESISTORS CHIP FIXED BULK METAL FOIL ULTRA PRECISION STYLE 0805.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Vendor recommended changes. Current DoD requirements. Editorial requirements throughout 6 Aug 2009 M. Radecki B Vendor address change. Add new vendor. Editorial changes throughout. 1 Mar 2013 M. Radecki Prepared in accordance with ASME Y14.100 Source contro

2、l drawing REV STATUS OF PAGES REV B B B B B B B B PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Jesus V. Garcia III DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 1 November 2007 CHECKED BY Andrew R. Ernst TITLE RESISTORS, CHIP, FIXED, BULK METAL FOIL, ULTRA PRECISION, STYLE 0805

3、 APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 07024 REV B PAGE 1 OF 8 AMSC N/A 5905-2012-E09 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

4、ut license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07024 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a bulk metal foil, ultra precision, chip resistor, style 0805. 1.2 Part or Identifying Number (PIN). The compl

5、ete PIN is as follows: 07024 - * * * Drawing number Resistance value (see 3.3.1) Power rating (see 3.3.3) Tolerance (see 3.3.4) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handbooks form a part of this document to

6、the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space

7、 Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-690 - Failure Rate Sampling Plans and Procedures. MIL-STD-790 - Standard Practice for Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specif

8、ications. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the DLA Document Service, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict betwe

9、en the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. R

10、EQUIREMENTS 3.1 Item requirements. The individual item requirements shall be as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-55342 and herein (see figure 1). Passivation is not applicable, however, a protective coatin

11、g over the element shall be provided. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07024 REV B PAGE 3 L W T D .080 .005 .050 .005 .025 MAX .015 .005 NOTES: 1. Dimen

12、sions are in Inches. Metric equivalents are given for general information only. 2. The pictorial view of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects

13、of the device, are acceptable. 3. Tolerances shall be +/- 0.005 inch (+/- 0.13 mm) unless otherwise specified. 4. The bottom view shown above represents the mounting side. FIGURE 1. Chip resistor. 3.3 Electrical characteristics 3.3.1 Resistance. The nominal resistance expressed in ohms is identified

14、 by six characters, consisting of five digits and a letter. The letter is used simultaneously as a decimal point and as a multiplier. For resistance values: a. Greater than or equal to 1 ohm but less than 1,000 ohms, the letter “R“ is used to represent a decimal point. b. Greater than or equal to 1,

15、000 ohms but less than 1 megohm, the letter “K“ is used to denote that a decimal point is located three places to the right. All digits preceding and following the letters (R or K) of the group represent significant figures. The resistance value designations are shown in table I. Minimum and maximum

16、 resistance values shall be as specified in 3.3.2. Inches mm .005 0.13 .015 0.38 .025 0.64 .050 1.27 .080 2.03 Uncoated ceramic Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3

17、 DWG NO. 07024 REV B PAGE 4 TABLE I. Designation of resistance values. Designation Resistance ohms 10R000 to 99R999 incl. 10 to 99.999 incl. 100R00 to 999R99 incl. 100 to 999.99 incl. 1K0000 to 7K0000 incl. 1000 to 7,000 incl. 3.3.2 Resistance range and resistance temperature characteristic. The res

18、istance range shall be from 10 ohms to 7 kilohms. The corresponding resistance temperature characteristic is specified in table II. Table II. Resistance range and resistance temperature characteristic. Resistance range (in ohms) Resistance Temperature Characteristic (RTC) in ppm/OC Power rating (see

19、 3.3.3) 250 - 12K 4 A 1/ 50 - 250 5 25 - 50 6 10 - 25 8 100 - 12K 2 B 1/ 50 - 100 3 10 - 50 4 250 - 7K 4 C 50 - 250 5 25 - 50 6 10 - 25 8 100 - 7K 3 D 50 - 100 4 10 - 50 5 1/ Inactive for new design with corresponding resistance range and RTC. 3.3.3 Power rating and maximum continuous working voltag

20、e. The power rating is at 70OC derated to +150OC at zero power (see figure 2) and is specified in table III. Table III. Power rating and maximum continuous working voltage. Symbol Maximum power rating (mWatts) Voltage (in volts) A 1/ 100 E=PR E = Voltage P = Power R = Resistance B 1/ 200 C 100 D 200

21、 1/ Inactive for new design Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07024 REV B PAGE 5 3.3.4 Resistance tolerance. Resistors are available in resistance tolera

22、nces as specified in table IV. TABLE IV. Resistance tolerance. Symbol Resistance tolerance percent Available resistance range (in Ohms) T 1/ 0.01 250 to 12K Q 0.02 A 0.05 100 to 7K B 0.1 50 to 7K C 0.25 25 to 7K D 0.5 10 to 7K F 1.0 1/ Inactive for new design FIGURE 2. Derating curve. 3.3.5 Terminat

23、ion. The termination material shall be in accordance with MIL-PRF-55342, code letter B. 3.3.5.1 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall

24、 be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.4 Thermal shock. When resistors are tested as specified in MIL-PRF-55342 for thermal shock the change in resistance shall not exceed 0.03 percent +0.01 ohm. 3.5 Low temperature operation. When resistors are tested as specified in MIL

25、-PRF-55342 for low temperature operation the change in resistance shall not exceed 0.03 percent +0.01 ohm. 3.6 Short time overload. When resistors are tested as specified in MIL-PRF-55342 for short time overload the change in resistance shall not exceed 0.02 percent +0.01 ohm. 3.7 High temperature e

26、xposure. When resistors are tested as specified in MIL-PRF-55342 for high temperature exposure the change in resistance shall not exceed 0.03 percent +0.01 ohm. -65 -50 -25 0 25 50 75 100 125 150 175 Temperature (OC) 100 80 60 40 20 0 Percentofrated power70OC -55OC Provided by IHSNot for ResaleNo re

27、production or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07024 REV B PAGE 6 3.8 Resistance to soldering heat. When resistors are tested as specified in MIL-PRF-55342 for resistance to soldering heat the change

28、in resistance shall not exceed 0.02 percent +0.01 ohm. 3.9 Moisture resistance. When resistors are tested as specified in MIL-PRF-55342 for moisture resistance the change in resistance shall not exceed 0.1 percent +0.01 ohm. 3.10 Life. When resistors are tested as specified in MIL-PRF-55342 for life

29、 the change in resistance shall not exceed 0.05 percent +0.01 ohm. 3.11 Resistance temperature characteristic. When resistors are tested as specified in MIL-PRF-55342 the RTC shall not exceed the values specified (see 3.3.2). 3.12 Marking. Marking is not required on this resistor; however, each waff

30、le pack and each unit package shall be marked with the PIN assigned herein (see 1.2), the manufacturers identification code, the date code, and the lot code. At the option of the manufacturer, the resistor may be marked (i.e., laser, color dot, etc.). The marking shall remain legible after all tests

31、. 3.13 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-55342 Qualified Product List for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manuf

32、acturer and DLA Land and Maritime-VAT. 3.13.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as approved sources of supply. 3.14 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally

33、preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. 3.15 Workmanship. Resistors shall be processed in such a manner as to be uniform in qua

34、lity and be free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-55342 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Qualification inspection.

35、Qualification inspection is not applicable to this document. 4.3 Product level qualification. The product level qualification specified in MIL-PRF-55342 and MIL-STD-690 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. Inspection of product for

36、 delivery shall consist of group A inspection (ER level only. PPM reporting, subgroup 1, subgroup 3, are not applicable) and group B inspection of MIL-PRF-55342. 4.4.1.1 Certification. The procuring activity may accept a certificate of compliance in lieu of Group B inspection. Provided by IHSNot for

37、 ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07024 REV B PAGE 7 5. PACKAGING 5.1 Packaging. For acquisition purpose, the packaging requirements shall be as specified in the contract or o

38、rder (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities wi

39、thin the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (Thi

40、s section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended to be used in thick or thin film circuits where microcircuity is intended, also, for use in surface mounting application. 6.2 Ordering data. The

41、 contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Packaging re

42、quirements (see 5.1). (i.e. Electrostatic discharge sensitive packaging). d. Whether the manufacturer performs the group B tests or provides certificate of compliance with group B (see 4.4.1.1). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit

43、tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation o

44、f tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Tolerance caution. Soldering temperature used during installation may

45、cause resistance to shift up to 0.05 %. 6.5 Recommended mounting. A low profile solder fillet is recommended (25 percent to 85 percent of chip “T“ dimension). IR, vapor phase, and convection reflow are recommended. The resistance element must be mounted in the up position to prevent failure of the p

46、art. 6.6 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to Government is controlled by MIL

47、-DTL-39032 that specifies a preventative packaging procedure. 6.7 Pulse applications. Designers are CAUTIONED on using these resistors in pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. These resistors only see a one

48、 time pulse (Short-time overload) as part of the group B inspection. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07024 REV B PAGE 8 6.8 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved on-line at resistordla.mil or in writing to: DLA Land and Maritime, A