DLA DSCC-DWG-05018 REV E-2009 CAPACITORS ULTRA LONG LIFE ALUMINUM CASE FLAT PACK 85 DEGREE C.pdf

《DLA DSCC-DWG-05018 REV E-2009 CAPACITORS ULTRA LONG LIFE ALUMINUM CASE FLAT PACK 85 DEGREE C.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-05018 REV E-2009 CAPACITORS ULTRA LONG LIFE ALUMINUM CASE FLAT PACK 85 DEGREE C.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Addition of tests and correction to test sequence 31 August 2007 Michael A. Radecki B Add correction for negative terminal and case 20 Dec 2007 Michael A. Radecki C Correct figure 1, add surge voltage in Table I 31 March 2008 Michael A. Radecki D Replaced t

2、able III with the same as 05019 table III 15 Nov 2008 Michael A. Radecki E Change table III C of C requirements 15 April 2009 Michael A. Radecki Prepared in accordance with ASME Y14.100-2000 Source control drawing REV E E E E E E E E E E PAGE 18 19 20 21 22 23 24 25 26 27 REV STATUS OF PAGES REV E E

3、 E E E E E E E E E E E E E E E PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PMIC N/A PREPARED BY Ken Bernier DESIGN ACTIVITY: DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 10 February 2006 CHECKED BY Ken Bernier TITLE CAPACITORS, ULTRA LONG LIFE ALUMINUM CASE FLAT PACK, 85

4、C, APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 05018 REV E PAGE 1 OF 27 AMSC N/A 5910-E426 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 0501

5、8 REV E PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the complete requirements for capacitors, ultra-long life, Aluminum, 85C, flat pack. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 05018- XXXX A | | Drawing Dash number Test plan option number (see Table I or Table II)

6、 (see Table III) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While ev

7、ery effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handboo

8、ks(Copies of these documents are available online at . The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE

9、STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-

10、5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provi

11、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 3 FIGURE 1A. Dimensions and configurationCase code . Length L (inches) EK 1.5 EA 2.0 EB 3.0 Inches mm Inche

12、s mm .010 0.25 .375 9.53 .020 0.51 .500 12.70 .030 0.76 .505 12.83 .036 0.91 1.00 25.40 .040 1.02 1.50 38.10 .156 3.96 1.75 44.45 .188 4.78 NOTES: 1. All dimensions in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only. 3. The negative lead is common to the

13、 case. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 4 Case code Length L (inches) EK 1.5 EA 2.0 EB 3.0 Inches mm .010 0.25 .020 0.51 .040 1.02 .500

14、 12.70 1.00 25.40 1.50 38.10 1.75 44.45 NOTES: 1. All dimensions in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only. 3. The negative lead is common to the case. FIGURE 1B. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

15、se from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 5 FIGURE 1C. Dimensions and configurationCase code . Length L (inches) EK 1.5 EA 2.0 EB 3.0 Inches mm .010 0.25 .020 0.51 .040 1.02 .500 12.70 .505 12.83 1.00 25.40 1.50 38.10 1.75 44.

16、45 NOTES: 1. All dimensions in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only. 3. The negative lead is common to the case. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS

17、COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 6 FIGURE 1D. Dimensions and configurationCase code . Length L (inches) EK 1.5 EA 2.0 EB 3.0 Inches mm Inches mm .010 0.25 .188 4.78 .020 0.51 .260 6.60 .030 0.76 .375 9.53 .036 0.91 .500 12.70 .040 1.02 .505 12.83 .156 3.96 1.00 25.

18、40 .175 4.45 1.75 44.45 NOTES: 1. All dimensions in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only. 3. The negative lead is common to the case. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUP

19、PLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 7 Case code Length L (inches) EK 1.5 EA 2.0 EB 3.0 FIGURE 1E. Dimensions and configurationInches . mm Inches mm .010 0.25 .260 6.60 .020 0.51 .500 12.70 .040 1.02 .505 12.83 .175 4.45 1.00 25.40 .188 4.78 1.75 4

20、4.45 NOTES: 1. All dimensions in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only. 3. The negative lead is common to the case. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBU

21、S COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 8 TABLE I. Styles MLP capacitorsDSCC Drawing 05018 . (Uninsulated) Cap. Cap. Tolerance (+/-) DC rated voltage DC Surge voltage ESR max m ESR max m Max. ac ripple current 120 Hz at 85C Max. ac ripple current 20 kHz at 85C Case Code

22、 Mounting Style A Mounting Style B Mounting Style C Mounting Style D Mounting Style E F percent volts +85C Volts +25C 120 Hz 20 kHz 120 Hz 20 kHz 05018 19000 20 7.5 10 76 66 4.2 4.5 EK 0001 1001 2001 3001 4001 05018 28000 20 7.5 10 50 44 5.8 6.2 EA 0002 1002 2002 3002 4002 05018 47000 20 7.5 10 30 2

23、6 9.1 9.8 EB 0003 1003 2003 3003 4003 05018 17000 20 10 13 77 67 4.2 4.5 EK 0004 1004 2004 3004 4004 05018 26000 20 10 13 51 45 5.8 6.1 EA 0005 1005 2005 3005 4005 05018 43000 20 10 13 30 27 9.0 9.6 EB 0006 1006 2006 3006 4006 05018 13000 20 16 20 81 69 4.1 4.4 EK 0007 1007 2007 3007 4007 05018 2100

24、0 20 16 20 53 46 5.7 6.1 EA 0008 1008 2008 3008 4008 05018 38000 20 16 20 31 27 9.0 9.6 EB 0009 1009 2009 3009 4009 05018 9600 20 20 25 84 69 4.0 4.4 EK 0010 1010 2010 3010 4010 05018 14000 20 20 25 56 46 5.5 6.1 EA 0011 1011 2011 3011 4011 05018 24000 20 20 25 33 27 8.7 9.6 EB 0012 1012 2012 3012 4

25、012 05018 8000 20 25 30 87 69 3.9 4.4 EK 0013 1013 2013 3013 4013 05018 12000 20 25 30 57 46 5.5 6.1 EA 0014 1014 2014 3014 4014 05018 20000 20 25 30 34 27 8.6 9.6 EB 0015 1015 2015 3015 4015 05018 5600 20 35 50 90 70 3.4 4.4 EK 0016 1016 2016 3016 4016 05018 8400 20 35 50 59 46 5.4 6.1 EA 0017 1017

26、 2017 3017 4017 05018 14000 20 35 50 35 27 8.4 9.6 EB 0018 1018 2018 3018 4018 05018 4400 20 50 63 97 70 3.7 4.4 EK 0019 1019 2019 3019 4019 05018 6600 20 50 63 62 46 5.2 6.1 EA 0020 1020 2020 3020 4020 05018 11000 20 50 63 36 27 8.3 9.6 EB 0021 1021 2021 3021 4021 05018 2200 20 63 75 101 76 3.7 4.2

27、 EK 0022 1022 2022 3022 4022 05018 3300 20 63 75 64 50 5.2 5.8 EA 0023 1023 2023 3023 4023 05018 5600 20 63 75 36 29 8.3 9.3 EB 0024 1024 2024 3024 4024 05018 1500 20 80 100 106 77 3.6 4.2 EK 0025 1025 2025 3025 4025 05018 2100 20 80 100 72 52 4.9 5.7 EA 0026 1026 2026 3026 4026 05018 3300 20 80 100

28、 44 31 7.5 9.0 EB 0027 1027 2027 3027 4027 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 9 TABLE I. Styles MLP capacitorsDSCC Drawing 05018 . (Unins

29、ulated) Cap. Cap. Tolerance (+/-) DC rated voltage DC Surge voltage ESR max m ESR max m Max. ac ripple current 120 Hz at 85C Max. ac ripple current 20 kHz at 85C Case Code Mounting Style A Mounting Style B Mounting Style C Mounting Style D Mounting Style E F percent volts +85C Volts +25C 120 Hz 20 k

30、Hz 120 Hz 20 kHz 05018 1100 20 100 125 112 78 3.5 4.2 EK 0028 1028 2028 3028 4028 05018 1600 20 100 125 76 54 4.7 5.6 EA 0029 1029 2029 3029 4029 05018 2700 20 100 125 46 33 7.4 8.7 EB 0030 1030 2030 3030 4030 05018 500 20 150 180 355 248 1.9 2.3 EK 0031 1031 2031 3031 4031 05018 770 20 150 180 238

31、166 2.7 3.2 EA 0032 1032 2032 3032 4032 05018 1300 20 150 180 143 100 4.2 5.0 EB 0033 1033 2033 3033 4033 05018 400 20 200 250 388 253 1.9 2.3 EK 0034 1034 2034 3034 4034 05018 600 20 200 250 261 168 2.6 3.2 EA 0035 1035 2035 3035 4035 05018 1000 20 200 250 158 100 3.8 5.0 EB 0036 1036 2036 3036 403

32、6 05018 330 20 250 300 426 258 1.8 2.3 EK 0037 1037 2037 3037 4037 05018 490 20 250 300 285 172 2.4 3.1 EA 0038 1038 2038 3038 4038 05018 820 20 250 300 172 103 3.8 4.9 EB 0039 1039 2039 3039 4039 05018 220 20 300 350 597 393 1.5 1.9 EK 0040 1040 2040 3040 4040 05018 330 20 300 350 399 262 2.1 2.5 E

33、A 0041 1041 2041 3041 4041 05018 560 20 300 350 240 157 3.2 4.0 EB 0042 1042 2042 3042 4042 05018 150 20 350 400 1000 734 1.2 1.4 EK 0043 1043 2043 3043 4043 05018 220 20 350 400 683 503 1.6 1.8 EA 0044 1044 2044 3044 4044 05018 370 20 350 400 420 310 2.3 2.8 EB 0045 1045 2045 3045 4045 05018 130 20

34、 400 450 1320 970 1.0 1.2 EK 0046 1046 2046 3046 4046 05018 200 20 400 450 882 648 1.4 1.6 EA 0047 1047 2047 3047 4047 05018 330 20 400 450 530 390 2.1 2.5 EB 0048 1048 2048 3048 4048 05018 130 20 420 475 1320 970 1.0 1.2 EK 0049 1049 2049 3049 4049 05018 200 20 420 475 882 648 1.4 1.6 EA 0050 1050

35、2050 3050 4050 05018 330 20 420 475 530 390 2.1 2.5 EB 0051 1051 2051 3051 4051 05018 110 20 450 500 1456 1190 0.96 1.1 EK 0052 1052 2052 3052 4052 05018 170 20 450 500 973 797 1.3 1.5 EA 0053 1053 2053 3053 4053 05018 280 20 450 500 585 480 2.0 2.3 EB 0054 1054 2054 3054 4054 Provided by IHSNot for

36、 ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 10 TABLE II. Styles MLP capacitorsDSCC Drawing 05018 . (Insulated) Cap. Cap. Tolerance (+/-) DC rated voltage DC Surge volta

37、ge ESR max m ESR max m Max. ac ripple current 120 Hz at 85C Max. ac ripple current 20 kHz at 85C Case Code Mounting Style A Mounting Style B Mounting Style C Mounting Style D Mounting Style E F percent volts +85C Volts +25C 120 Hz 20 kHz 120 Hz 20 kHz 05018 19000 20 7.5 10 76 66 4.2 4.5 EK 5001 6001

38、 7001 8001 9001 05018 28000 20 7.5 10 50 44 5.8 6.2 EA 5002 6002 7002 8002 9002 05018 47000 20 7.5 10 30 26 9.1 9.8 EB 5003 6003 7003 8003 9003 05018 17000 20 10 13 77 67 4.2 4.5 EK 5004 6004 7004 8004 9004 05018 26000 20 10 13 51 45 5.8 6.1 EA 5005 6005 7005 8005 9005 05018 43000 20 10 13 30 27 9.0

39、 9.6 EB 5006 6006 7006 8006 9006 05018 13000 20 16 20 81 69 4.1 4.4 EK 5007 6007 7007 8007 9007 05018 21000 20 16 20 53 46 5.7 6.1 EA 5008 6008 7008 8008 9008 05018 38000 20 16 20 31 27 9.0 9.6 EB 5009 6009 7009 8009 9009 05018 9600 20 20 25 84 69 4.0 4.4 EK 5010 6010 7010 8010 9010 05018 14000 20 2

40、0 25 56 46 5.5 6.1 EA 5011 6011 7011 8011 9011 05018 24000 20 20 25 33 27 8.7 9.6 EB 5012 6012 7012 8012 9012 05018 8000 20 25 30 87 69 3.9 4.4 EK 5013 6013 7013 8013 9013 05018 12000 20 25 30 57 46 5.5 6.1 EA 5014 6014 7014 8014 9014 05018 20000 20 25 30 34 27 8.6 9.6 EB 5015 6015 7015 8015 9015 05

41、018 5600 20 35 50 90 70 3.4 4.4 EK 5016 6016 7016 8016 9016 05018 8400 20 35 50 59 46 5.4 6.1 EA 5017 6017 7017 8017 9017 05018 14000 20 35 50 35 27 8.4 9.6 EB 5018 6018 7018 8018 9018 05018 4400 20 50 63 97 70 3.7 4.4 EK 5019 6019 7019 8019 9019 05018 6600 20 50 63 62 46 5.2 6.1 EA 5020 6020 7020 8

42、020 9020 05018 11000 20 50 63 36 27 8.3 9.6 EB 5021 6021 7021 8021 9021 05018 2200 20 63 75 101 76 3.7 4.2 EK 5022 6022 7022 8022 9022 05018 3300 20 63 75 64 50 5.2 5.8 EA 5023 6023 7023 8023 9023 05018 5600 20 63 75 36 29 8.3 9.3 EB 5024 6024 7024 8024 9024 05018 1500 20 80 100 106 77 3.6 4.2 EK 50

43、25 6025 7025 8025 9025 05018 2100 20 80 100 72 52 4.9 5.7 EA 5026 6026 7026 8026 9026 05018 3300 20 80 100 44 31 7.5 9.0 EB 5027 6027 7027 8027 9027 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A

44、 CODE IDENT NO. 037Z3 DWG NO. 05018 REV E PAGE 11 TABLE II. Styles MLP capacitorsDSCC Drawing 05018 . (Insulated) Cap. Cap. Tolerance (+/-) DC rated voltage DC Surge voltage ESR max m ESR max m Max. ac ripple current 120 Hz at 85C Max. ac ripple current 20 kHz at 85C Case Code Mounting Style A Mount

45、ing Style B Mounting Style C Mounting Style D Mounting Style E F percent volts +85C Volts +25C 120 Hz 20 kHz 120 Hz 20 kHz 05018 1100 20 100 125 112 78 3.5 4.2 EK 5028 6028 7028 8028 9028 05018 1600 20 100 125 76 54 4.7 5.6 EA 5029 6029 7029 8029 9029 05018 2700 20 100 125 46 33 7.4 8.7 EB 5030 6030

46、 7030 8030 9030 05018 500 20 150 180 355 248 1.9 2.3 EK 5031 6031 7031 8031 9031 05018 770 20 150 180 238 166 2.7 3.2 EA 5032 6032 7032 8032 9032 05018 1300 20 150 180 143 100 4.2 5.0 EB 5033 6033 7033 8033 9033 05018 400 20 200 250 388 253 1.9 2.3 EK 5034 6034 7034 8034 9034 05018 600 20 200 250 26

47、1 168 2.6 3.2 EA 5035 6035 7035 8035 9035 05018 1000 20 200 250 158 100 3.8 5.0 EB 5036 6036 7036 8036 9036 05018 330 20 250 300 426 258 1.8 2.3 EK 5037 6037 7037 8037 9037 05018 490 20 250 300 285 172 2.4 3.1 EA 5038 6038 7038 8038 9038 05018 820 20 250 300 172 103 3.8 4.9 EB 5039 6039 7039 8039 90

48、39 05018 220 20 300 350 597 393 1.5 1.9 EK 5040 6040 7040 8040 9040 05018 330 20 300 350 399 262 2.1 2.5 EA 5041 6041 7041 8041 9041 05018 560 20 300 350 240 157 3.2 4.0 EB 5042 6042 7042 8042 9042 05018 150 20 350 400 1000 734 1.2 1.4 EK 5043 6043 7043 8043 9043 05018 220 20 350 400 683 503 1.6 1.8 EA 5044 6044 7044 8044 9044 05018 370 20 350 400 420 310 2.3 2.8 EB 5045 6045 7045 8045 9045 05018 130 20 400 450 1320 970 1.0 1.2 EK 5046 6046 7046 8046 9046 05018 200 20 4