DLA DSCC-DWG-05003 REV C-2013 CAPACITORS FIXED CERAMIC CHIP 0402 HIGH FREQUENCY BP.pdf

《DLA DSCC-DWG-05003 REV C-2013 CAPACITORS FIXED CERAMIC CHIP 0402 HIGH FREQUENCY BP.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-05003 REV C-2013 CAPACITORS FIXED CERAMIC CHIP 0402 HIGH FREQUENCY BP.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added approved source of supply. Revised table IV. Added 6.4. Removed table from 3.3.1 17 April 2008 Michael A. Radecki B Changed address of vendor B. 1 July 2010 Michael A. Radecki C Updated vendor offerings. 26 September 2013 Michael A. Radecki Prepared i

2、n accordance with ASME Y14.100 REV STATUS OF PAGES REV C C C C C C C C PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY MICHAEL A. RADECKI DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 3 January 2005 CHECKED BY MICHAEL A. RADECKI TITLE CAPACITORS, FIXED, CERAMIC, CH

3、IP, 0402, HIGH FREQUENCY, BP APPROVED BY KENDALL A. COTTONGIM SIZE A CODE IDENT. NO. 037Z3 DWG NO. 05003 REV C PAGE 1 OF 8 AMSC N/A 5910-2013-E22CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction

4、or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05003 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55681 describe the requirements for ceramic, chip. 1.2 Part or Identifying Number (PIN) The complete

5、 PIN is as follows: 05003- 2R0 B C Z - Drawing number Capacitance value (see 1.2.1) Voltage (see 1.2.2) Capacitance tolerance (see 1.2.3) Termination finish (see 1.2.4) Group C testing option (see 1.2.5) 1.2.1 Capacitance value. The nominal capacitance value, expressed in picofarads (pF) is identifi

6、ed by a three digit number; the first two digits represent significant figures and the last digit specifies the number of zeros to follow. When the nominal value is less than 10 pF, the letter “R” is used to indicate the decimal point and the succeeding digit(s) of the group represent significant fi

7、gure(s). 1R0 indicates 1.0 pF; R75 indicates .75 pF; and 0R5 indicates 0.5 pF. See table IV for values. 1.2.2 Voltage. The rated voltage for continuous operation at +125C is identified by a single letter as shown in table I. TABLE I. Rated voltage. Symbol Rated voltage (volts, dc) Z 25 A 50 B 100 C

8、200 1.2.3 Capacitance tolerance. The capacitance tolerance is identified by a single letter in accordance with table II. TABLE II. Capacitance tolerance. Symbol Capacitance tolerance () A .05 pF B .1 pF C .25 pF D .50 pF F 1 percent G 2 percent J 5 percent K 10 percent M 20 percent 1.2.4 Termination

9、 finish. Termination finish is identified by a single letter as shown in table III. TABLE III. Termination finish. Symbol Termination finish M Palladium-silver Z Base metallization-barrier metal-tinned (tin/lead alloy, with a minimum of 4 percent lead) Provided by IHSNot for ResaleNo reproduction or

10、 networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05003 REV C PAGE 3 1.2.5 Group C testing option. To require MIL-PRF-55681 group C testing, use the appropriate letter from the table below. If group C testing is not

11、desired, leave this location blank. NOTE: Ordering group C options that contain a 2,000 hour life test may extend the processing time by 90 days or more. Letter Group C testing option C Full group C L 2,000 hour life test only M 1,000 hour life test only H Low voltage humidity only N/A No group C te

12、sting. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4 and 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every eff

13、ort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The

14、 following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (See 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55681 - Capacitor, Chip,

15、Multiple Layer, Fixed, Unencapsulated, Ceramic Dielectric, Established Reliability and Non-Established Reliability, General Specification For. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts, Test Methods for. MIL-STD-1285 - Marking of Electrical and Electroni

16、c Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict

17、 between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requ

18、irements shall be in accordance with MIL-PRF-55681, and as specified herein. These capacitors shall be capable of meeting all electrical, environmental, and mechanical requirements of MIL-PRF-55681, unless otherwise stated. 3.2 Interface and physical dimensions. The interface and physical dimensions

19、 shall be as specified in MIL-PRF-55681 and herein (see figure 1). 3.2.1 Tin plated finishes. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 4 percent (see 6.4). Provided by IHSNot for ResaleNo reprod

20、uction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05003 REV C PAGE 4 T W Y L NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Dimensions and tolerances are

21、 for bare chips. For solder coated terminations (symbol U), add .020 inch (0.51 mm) to the positive length tolerance and .015 inch (0.38 mm) to the positive width and thickness tolerances. FIGURE 1. Case dimensions and configuration. 3.3 Electrical characteristics. 3.3.1 Dielectric type. The dielect

22、ric type shall be BP (30 ppm/C) ceramic in accordance with MIL-PRF-55681. 3.3.2 Capacitance. Capacitance shall be in accordance with table IV when measured in accordance with method 305 or MIL-STD-202. The following conditions shall apply: 1,000 pF 1 MHz 50 kHz 1 V rms .2 V rms 1,000 pF 1 kHz 50 Hz

23、1 V rms .2 V rms Inches mm .004 0.10 .006 0.15 .010 0.25 .020 0.51 .024 0.61 .040 1.02 Dimensions L .004 W .004 T Max Y .006 .040 .020 .024 .010 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A COD

24、E IDENT NO. 037Z3 DWG NO. 05003 REV C PAGE 5 3.3.3 Dissipation factor (+25C). When measured at the frequency and voltage specified in 3.3.2, the dissipation factor shall be 0.05 percent. 3.3.4 Insulation resistance. At +25C: minimum of 100,000 megohms or 1,000 megohm-microfarads, whichever is less.

25、At +125C: minimum of 1,000 megohms or 10 megohm-microfarads, whichever is less. 3.4 Solderability. In accordance with MIL-PRF-55681, except the sample size shall be 5 pieces with zero defectives permitted. 3.5 Moisture resistance. In accordance with MIL-PRF-55681, with the following exceptions: a. P

26、olarizing voltage shall be rated voltage. b. Testing may be performed on chips with a larger width and/or length as long as they are cut from the same wafer(s) as those used for production. 3.6 Marking. As a minimum, marking shall be on the package due to the small size of the chips. The package mar

27、king shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in paragraph 1.2 with manufacturers name or CAGE code and date code. The manufacturer may, at their option, mark some information on the chips. Suggested marking is the 2 digit EIA capacitance code. 3.7 Manufacturer

28、eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-55681 Qualified Products List for at least one part, or perform the group A and group C inspections of MIL-PRF-55681on a sample of parts agreed upon by the manufacturer and DLA Land

29、 and Maritime-VA. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be us

30、ed to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.10 Workmanship. In accordance with MIL-PRF-55681. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspect

31、ion is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A of MIL-PRF-55681. ESR testing and PPM testing and calculation are not applicable. When optional group C testing is requested,

32、terminal strength and series resonance are not applicable. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel

33、 need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval

34、 is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS C

35、OLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05003 REV C PAGE 6 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do

36、 not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exis

37、ts and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the con

38、formance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for notification of change of product to acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Replaceabili

39、ty. Capacitors covered by this drawing will replace the same commercial device covered by a contractor-prepared specification or drawing. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiske

40、rs may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have s

41、hown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and

42、 the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at capacitorfilterdla.mil or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. 6.6 Cha

43、nges from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contract

44、ors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COL

45、UMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05003 REV C PAGE 7 TABLE IV. Electrical characteristics. DSCC Drawing 05003- 1/ Capacitance pF Available tolerances ATC Vendor A Available voltages VISHAY 2/ Vendor B Available voltages Z A B C K Z A B C K 25 50 100 200 250 25 50 100 200 250 0

46、R1- - - - .1 A, B 0R2- - - - .2 A, B,C 0R3- - - - .3 A, B, C 0R4- - - - .4 A, B, C 0R5- - - - .5 A, B, C 0R6- - - - .6 A, B, C,D 0R7- - - - .7 A, B, C,D 0R8- - - - .8 A, B, C,D 0R9- - - - .9 A, B, C,D 1R0- - - - 1 A, B, C 1R1- - - - 1.1 A, B, C, D 1R2- - - - 1.2 A, B, C, D 1R3- - - - 1.3 A, B, C, D

47、1R5- - - - 1.5 A, B, C, D 1R6- - - - 1.6 A, B, C, D 1R7- - - - 1.7 B, C, D 1R8- - - - 1.8 A, B, C, D 2R0- - - - 2 A, B, C, D 2R1- - - - 2.1 B, C, D 2R2- - - - 2.2 A, B, C, D 2R4- - - - 2.4 A, B, C, D 2R7- - - - 2.7 A, B, C, D 3R0- - - - 3 A, B, C, D 3R3- - - - 3.3 A, B, C, D 3R6- - - - 3.6 A, B, C,

48、D 3R9- - - - 3.9 A, B, C, D 4R3- - - - 4.3 A, B, C, D 4R7- - - - 4.7 A, B, C, D 5R1- - - - 5.1 A, B, C, D 5R6- - - - 5.6 A, B, C, D 6R2- - - - 6.2 A, B, C, D 6R8- - - - 6.8 B, C, J, K, M 7R5- - - - 7.5 B, C, J, K, M 8R2- - - - 8.2 B, C, J, K, M 9R1- - - - 9.1 B, C, J, K, M 100- - - - 10 F, G, J, K, M 110- - - - 11 F, G, J, K, M