DLA DSCC-DWG-04018-2005 CONNECTOR PLUG ELECTRICAL RADIO FREQUENCY 2 4MM SOCKET CONTACT FOR SEMIRIGID CABLE《半刚性电缆插座接触无线电频率2 4毫米电工插头连接器》.pdf

《DLA DSCC-DWG-04018-2005 CONNECTOR PLUG ELECTRICAL RADIO FREQUENCY 2 4MM SOCKET CONTACT FOR SEMIRIGID CABLE《半刚性电缆插座接触无线电频率2 4毫米电工插头连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-04018-2005 CONNECTOR PLUG ELECTRICAL RADIO FREQUENCY 2 4MM SOCKET CONTACT FOR SEMIRIGID CABLE《半刚性电缆插座接触无线电频率2 4毫米电工插头连接器》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 PREPARED BY PMIC G Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 CHECKED B

2、Y TITLE Mary McWilliams APPROVED BY Richard Taylor CONNECTOR, PLUG, ELECTRICAL, RADIO FREQUENCY 2.4mm, SOCKET CONTACT, FOR SEMIRIGID CABLE SIZE CAGE CODE 037Z3 DWG. NO. 04018 Original date of drawing 30 November 2005 A REV PAGE 1 OF 10 AMSC N/A 5935-E745 Provided by IHSNot for ResaleNo reproduction

3、or networking permitted without license from IHS-,-,-NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Metric equivalents are in parentheses. 4. All undimensioned pictorial representations are for reference purposes only. 5. Wrench flats to accommodate stan

4、dard wrench in accordance with FED-STD-H28, appendix 10. 6. Dimension A defines the length of connector when assembled to the cable. 7. All threads shall conform to FED-STD-H28. 8. Series 2.4mm, socket contact interface, in accordance with figure 2. FIGURE 1. General configuration. SIZE CAGE CODE DW

5、G NO. 037Z3 04018 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTES: DEFENSE SUPPLY CENTER, COLUMBUS Provided by IHSNot for ResaleNo reproduction or networking per

6、mitted without license from IHS-,-,-1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Metric equivalents are in parentheses. FIGURE 2. Interface dimensions (2.4 mm). SIZE CAGE CODE DWG NO. 037Z3 04018 P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE3 Inches mm In

7、ches mm .003 0.08 .095 2.41 .004 0.10 .104 2.64 .005 0.13 .118 3.00 .006 0.15 .122 3.10 .008 0.20 .1878 4.770 .022 0.56 .1888 4.795 .024 0.61 .189 4.80 .0409 1.039 .199 5.05 .0415 1.054 .228 5.79 .054 1.37 .232 5.89 .060 1.52 .236 5.99 .064 1.62 .094 2.39 TABLE I. Dash number and applicable cable. D

8、imension A # Dimension B Part Identifying Number (PIN) Applicable cable 1/ Before assembly After assembly CATEGORY E FIELD REPLACEABLE 2/ 3/ 4/ (STANDARD ASSEMBLY TOOL KIT) 04018ZSPA-1 04018ZCGA-1 M17/133-RG405*M17/133-00001 through M17/133-00018 Not applicable.850 (21.59 mm) maximum Not Applicable

9、04018ZSPA-2 04018ZCGA-2 M17/133-RG405*M17/133-00001 through M17/133-00018 Not applicable.550 (13.97 mm) maximum .275 .010 (6.98 mm 0.25 mm) * Cable to be used when performing test requiring cable. # Dimension A determines the closeness of a bend in the cable to the rear of the connector. 1/ MIL-DTL-

10、17 cables are specified by the basic number. The latest version of each cable shall be applicable. 2/ These connectors have captivated center contacts. 3/ Kit number Amphenol 901-2500, or equivalent. 4/ All corrosion-resistant steel-bodied connectors shall be gold-plated in accordance with ASTM B488

11、, type II code C, class 1.27, over 50 micro inches (1.27 micro meters) minimum of nickel in accordance with SAE-AMS-QQ-N-290. SIZE CAGE CODE DWG NO. 037Z3 04018 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE4 Provided by IHSNot for ResaleNo reproduction or networki

12、ng permitted without license from IHS-,-,-NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parenthesis and are given for information only. 3. Tapering of center conductor is optional. FIGURE 3. Cable stripping dimensions for category E connectors. SIZE CAGE CODE DWG NO. 037Z3 04018 D

13、EFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE5 Cable Dimension “A” M17/133-RG405 M17/133-00001 through M17/133-00018 .070 .005 (1.78 0.13) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ENGINEERING DATA: Nominal im

14、pedance: 50 ohms. Frequency range: 0 to 50 GHz. Voltage rating: The voltage rating shall be in accordance with table II. TABLE II. Voltage rating. Cable Voltage maximum (at sea level) Voltage maximum (70,000 feet) M17/133-RG405 M17/133-00001 through M17/133-00018 V rms335 V rms85 Temperature rating:

15、 -65C to +165C. Category F: Connectors using semirigid cables with standard stripping dimensions and using standard military assembly tools. The method of assembly or the connector to the cable shall be solderless. REQUIREMENTS: Dimensions and configuration: See figure 1. Force to engage and disenga

16、ge: Longitudinal force: Not applicable. Torque: 2 inch-pounds maximum. Coupling proof torque: Not applicable. Inspection conditions: For each test of threaded coupling connector where the test is performed on mated pairs, the pairs shall be torqued to 7 to 10 inch-pounds. Mating characteristics: See

17、 figures 2, 3 and 4. Center contact (socket): Oversize test pin: .0206 + .0001. Test pin finish: 16 microinches. Insertion depth: .030/.045. Number of insertions: 3. SIZE CAGE CODE DWG NO. 037Z3 04018 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE6 Provided by IHSN

18、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Insertion force test: Steel test pin diameter .0201 + .0001. Insertion depth: .050/.075. Test pin finish: 16 microinches. Insertion force: 2 pounds maximum. Withdrawal force test: Steel test pin diameter .0196 - .0001.

19、 Insertion depth: .050/.075. Withdrawal force: 1 ounce minimum. Test pin finish: 16 microinches. FIGURE 4. Test pin data. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Insulation resistance: Method 302, test condition B of MIL-STD-202, 5,000 megohms minimum. Center

20、 contact retention: 6 pounds minimum axial force. Radial torque: Not applicable. Corrosion (salt spray): Method 101, test condition B of MIL-STD-202. Voltage standing wave ratio (VSWR): From 0.5 to 50 GHz, or approximately 80 percent of upper cutoff frequency of the cable, whichever is lower. Cables

21、 VSWRM17/133-RG405 M17/133-00001 1.07 + 0.01 F (GHz) through M17/133-00018 SIZE CAGE CODE DWG NO. 037Z3 04018 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE7 Inch mm .015 0.38 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

22、 IHS-,-,-Swept frequency VSWR test setup: Item 6: VSWR shall be less than 1.025 + .002 F (F in GHz). Item 16: VSWR shall be less than 1.025 + .002 F (F in GHz). Second step of VSWR checkout procedure: VSWR shall be less than 1.080 + .005 F (F in GHz). Connector durability: 500 cycles minimum at 12 c

23、ycles per minute maximum. The connector shall meet the mating characteristics and force to engage and disengage requirements. Contact resistance: In milliohms, maximum. Initial After environmentCenter contact: 3.0 4.0 Outer contact: 2.0 Not applicable Outer conductor to body: 0.5 1/ Not applicable D

24、ielectric withstanding voltage at sea level: Method 301 of MIL-STD-202. Cables V rmsM17/133-RG405 1,000 M17/133-00001 through M17/133-00018 Vibration, high frequency: Method 204, test condition D of MIL-STD-202, except the method of mounting shall be approved by the qualifying activity. No discontin

25、uity permitted. Shock (specified pulse): Method 213, test condition I of MIL-STD-202. Thermal shock: Method 107, test condition B of MIL-STD-202, except test high temperature shall be +115C. Moisture resistance: Method 106 of MIL-STD-202. No measurements at high humidity. Insulation resistance shall

26、 be at least 200 megohms within 5 minutes after removal from humidity. Corona level: Altitude: 70,000 feet. Cables Volts (minimum)M17/133-RG405 250 M17/133-00001 through M17/133-00018 1/ Five milliohms is permissible for passivated steel bodied connectors only. SIZE CAGE CODE DWG NO. 037Z3 04018 DEF

27、ENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RF high potential withstanding voltage: Frequency: 5 MHz to 7.5 MHz. Leakage current: Not applicable. Cables V rmsM17/133-

28、RG405 670 M17/133-00001 through M17/133-00018 Cable retention force: The cable retention force shall be as specified in table III. TABLE III. Cable retention force. Cable Pounds (minimum) Torque 1/ inch-ounce M17/133-RG405 M17/133-00001 through M17/133-00018 30 16 1/ Torque to be applied 4 inches ma

29、ximum from the end of the connector. Reverse bend not applicable. Coupling mechanism retention force: Not applicable. RF leakage: -90 dB minimum, tested at a frequency between 2 and 3 GHz. RF insertion loss: dB maximum = .03 x F GHz. Test frequency at a frequency between .5 to 50 GHz. PIN: See table

30、 I. SIZE CAGE CODE DWG NO. 037Z3 04018 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Approved sources of supply are listed herein. Additional sources will be added a

31、s they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 04018ZSPA-1 SF1621-6001 04018ZCGA-1 1621-4001 04018ZSPA-2 SF1621-6002 04018Z

32、CGA-2 95077 1621-4002 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor Name and number address95077 S/V Microwave, Inc. 2400 Centrepark West Dr. West Palm Beach, FL 33409 SIZE CAGE CODE DWG NO. 037Z3 04018 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-