DLA DSCC-DWG-04015-2004 CONNECTOR RECEPTACLE ELECTRICAL SERIES BMZ PIN CONTACT RIGHT ANGLE FOR SEMIRIGID CABLE《半刚性电缆用BMZ系列直角针接触电机贮器连接器》.pdf

《DLA DSCC-DWG-04015-2004 CONNECTOR RECEPTACLE ELECTRICAL SERIES BMZ PIN CONTACT RIGHT ANGLE FOR SEMIRIGID CABLE《半刚性电缆用BMZ系列直角针接触电机贮器连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-04015-2004 CONNECTOR RECEPTACLE ELECTRICAL SERIES BMZ PIN CONTACT RIGHT ANGLE FOR SEMIRIGID CABLE《半刚性电缆用BMZ系列直角针接触电机贮器连接器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY Lee Surowiec APPROVED B

2、Y Richard Taylor TITLE CONNECTOR, RECEPTACLE, ELECTRICAL, SERIES BMZ, PIN CONTACT, RIGHT ANGLE, FOR SEMIRIGID CABLE SIZE CAGE CODE 037Z3 DWG. NO. 04015 Original date of drawing 30 June 2004 A REV PAGE 1 OF 5 AMSC N/A 5935-E742 Provided by IHSNot for ResaleNo reproduction or networking permitted with

3、out license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04015 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Wrench flats are to accommodate standard wrench opening in accordance

4、with FED-STD-H28, appendix 10. 4. All undimensioned pictorial configurations are for reference purposes only. 5. Dimension .583 (14.80 mm) defines the maximum overall length of the connector when assembled to the cable. 6. Method of assembly to the cable shall be solder. 7. Unless otherwise specifie

5、d, tolerances are .005 (0.13 mm). 8. Series BMZ interface in accordance with MIL-STD-348, pin contact. FIGURE 1. General configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04015 DEFENSE SUPPLY CENTER, COLUMBUS

6、 COLUMBUS, OH 43216-5000 A REV PAGE 3 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 - 18 GHz. (Connector performance only, frequency range is dependent on cable used.) Voltage rating: 335 V rms at sea level. 85 V rms at 70,000 feet. Temperature rating: -65C to +165C. REQUIREMENTS:

7、 Requirements of drawing 84148 applicable. Dimensions and configuration: See figure 1 and MIL-STD-348. Force to engage and disengage: Longitudinal force: 12 ounces, max. Torque: Not applicable. Coupling proof torque: Not applicable. Hermetic seal: Not applicable. Leakage (pressurized connectors): No

8、t applicable. Center contact retention: 4 pounds minimum, axial force Radial torque: Not applicable. Voltage standing wave ratio (VSWR): 1.07 + .010 F (GHz), maximum. Moisture resistance: Method 106, MIL-STD-202, no measurements at high humidity. Insulation resistance shall be at least 200 megohms w

9、ithin 5 minutes after removal from humidity. Insulation resistance: Method 302, test condition B of MIL-STD-202, 10,000 megohms, minimum. Contact resistance (in milliohms, maximum): Initial After environment Center contact: 4.0 4.0 Outer contact: 2.0 Not applicable Outer conductor to body: 0.5 Not a

10、pplicable Dielectric withstanding voltage at sea level: 1000 V rms, minimum. 250 V rms at 70,000 feet. Vibration, high frequency: Method 204, test condition D, MIL-STD-202. Corona level: Altitude: 70,000 feet. 250 V rms, minimum. Shock (specified pulse): Method 213, test condition I, MIL-STD-202. Pr

11、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04015 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 4 Thermal shock: Method 107, test condition B, MIL-STD-202, except test high temperature shall be +85C

12、. Barometric pressure (reduced): Not applicable. RF high potential withstanding voltage: 670 V rms, minimum. Frequency: 5 MHz. Leakage current: Not applicable. Cable retention force: 30 pounds, minimum. Torque: 16 ounce-inches, minimum. Coupling mechanism retention force: Not applicable. RF leakage:

13、 -85 F (F in GHz) dB, minimum. Test at a frequency between 2 and 3 GHz. RF insertion loss: .04 F, GHz dB, maximum. Note: These parts are for use in general radio frequency applications. Part or Identifying Number (PIN): See table I. TABLE I. Connector to cable reference. PIN Cable accommodation 0401

14、5ZSPA M17/133-RG405 M17/133-0001 through -00005 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04015 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 5 Approved sources of supply are listed herein. Addi

15、tional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 04015ZSPA 95077 SF8903-6007 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name and Number Address 95077 S/V Microwave, Inc. 2400 Centrpark West Dr. WPB, Fl 33409 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-