DLA DSCC-DWG-03014 REV B-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE 0402 [Use DLA MIL-PRF-32159 11 (1) DLA MIL-PRF-32159 11]《0402型0欧姆涂膜固定片状电阻器(可用 国防后勤局标准-PRF-32159 11)》.pdf

《DLA DSCC-DWG-03014 REV B-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE 0402 [Use DLA MIL-PRF-32159 11 (1) DLA MIL-PRF-32159 11]《0402型0欧姆涂膜固定片状电阻器(可用 国防后勤局标准-PRF-32159 11)》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-03014 REV B-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE 0402 [Use DLA MIL-PRF-32159 11 (1) DLA MIL-PRF-32159 11]《0402型0欧姆涂膜固定片状电阻器(可用 国防后勤局标准-PRF-32159 11)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add manufacturer. Editorial changes throughout. 4 SEP 03 K. Cottongim B Inactive for new design. Revise to present DoD policy requirements. 12 Apr 05 Kendall A. Cottongim Notice of Inactivation for New Design DSCC Drawing 03014 is inactive for new design an

2、d is no longer used, except for replacement purposes. Use MIL-PRF-32159/11 Prepared in accordance with ASME Y14.100 Selected item drawing REV B B A B B REV STATUS OF PAGES PAGES 1 2 3 4 5 PMIC N/A PREPARED BY Andrew R. Ernst DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY Andrew R. Ernst APP

3、ROVED BY Kendall A. Cottongim TITLE RESISTOR, CHIP, FIXED, FILM, ZERO-OHM, STYLE 0402 SIZE A CODE IDENT. NO. 037Z3 DWG NO. 03014 Original date of drawing 20 June 2003 REV B PAGE 1 OF 5 AMSC N/A 5905-E529 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

4、,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03014 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a fixed, film, .040 X .020, zero-ohm, chip resistor. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows and is ava

5、ilable in wrap-around termination: 03014 - B | | | | Drawing Termination number (See 3.2.1) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified he

6、rein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Specification for. DEPARTMENT

7、OF DEFENSE STANDARDS MIL-STD-790 - Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specification. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/a

8、ssist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text

9、 of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55342 and as specified herein.

10、3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-55342 and herein (see figure 1). 3.2.1 Termination material. The termination material shall be in accordance with MIL-PRF-55342 and code letters B, C, G, or U. Provided by IHS

11、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03014 REV B PAGE 3 A B C D E .042 .008 .022 .005 .010/.033 .010 .005 .010 .005 NOTES: 1. Dimensions are in inches. 2. Metric equivalen

12、ts are given for general information only. 3. The pictorial view of the style above is given as representative of the item. Slight deviations from the outline shown, which are contained within the envelope, and do not alter the functional aspect of the device, are acceptable. FIGURE 1. Zero-ohm chip

13、 resistor style 0402. 3.3 Electrical characteristics. 3.3.1 Temperature range. The temperature range shall be -55C to +125C. 3.3.2 Resistance. The resistance shall not exceed 0.025 ohm. 3.4 Marking. Marking of the individual chip resistors is not required; however, each unit package shall be marked

14、in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, date, and lot codes. Inches .005 .008 .010 .022 .033 .042 mm 0.127 0.203 0.254 0.559 0.838 1.067 Provided by IHSNot for ResaleNo reproduction or

15、networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03014 REV B PAGE 4 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the

16、 maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested sou

17、rce of supply. 3.7 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-55342 and maintained in accordance with MIL-STD-790 is n

18、ot applicable to this document. 4.2 Qualification inspection. Qualification inspection is not applicable to this document. 4.3 Product level qualification. The product level qualification specified in MIL-PRF-55342 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection of p

19、roduct for delivery. Inspection of product for delivery shall consist of group A inspection (established reliability level only and the parts per million reporting is not applicable) of MIL-PRF-55342. 4.5 Visual and mechanical examination. Resistors shall be examined to verify that the materials, de

20、sign, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-55342. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel

21、 is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agenc

22、y, or within the Military Services System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general

23、 or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended for use in thick or thin film circuits where microcircuitry is intended; also in most surface mount applications. 6.2 Ordering data. The contract or purchase order should specify the foll

24、owing: a. Complete PIN (see 1.2). b. Requirements for delivery and one copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record.

25、 Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at Resistordla.mil or in writing to: DSCC-VAT, 3990 East Broad Street,

26、Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03014 REV B PAGE 5 6.4 Suggested sources of sup

27、ply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at Resistordla.mil or contact DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850

28、-0552. DSCC drawing PIN 03014-* Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address Termination styles B, C, G, U H0402CP*000(D03014) 56235 State of the Art, Incorporated 2470 Fox Hill Road State College, PA 16803-1797 Termination styles B RCWPM-0402-68 91637 Vishay Da

29、le Electronics PO Box 609 Columbus, NE 68602-0609 Plant: Vishay Israel, Ltd Emek-Sara “B” Industrial Park Beer Sheva, Israel 84874 Termination styles B M0402XR000SB 57498 Vishay Thin Film 2160 Liberty Drive Niagara Falls, NY 14304 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-