DLA DSCC-DWG-03011 REV A-2010 RESISTOR FIXED FILM CHIP ZERO-OHM STYLE 0201.pdf

《DLA DSCC-DWG-03011 REV A-2010 RESISTOR FIXED FILM CHIP ZERO-OHM STYLE 0201.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-03011 REV A-2010 RESISTOR FIXED FILM CHIP ZERO-OHM STYLE 0201.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add vendor. Dimensional changes. Added solder mounting integrity paragraph. Change reference document from MIL-PRF-55342 to MIL-PRF-32159. Editorial changes throughout. 20 APR 10 M. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV

2、 STATUS OF PAGES REV A A A A A PAGES 1 2 3 4 5 PMIC N/A PREPARED BY Andrew R. Ernst DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 24 July 2003 CHECKED BY Andrew R. Ernst TITLE RESISTOR, FIXED, FILM, CHIP, ZERO-OHM, STYLE 0201 APPROVED BY Kendall A. Cottongim SIZE A CODE IDENT

3、. NO. 037Z3 DWG NO. 03011 REV A PAGE 1 OF 5 AMSC N/A 5905-E702 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03011 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing desc

4、ribes the requirements for a fixed, film, zero-ohm, chip resistor, style 0201. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows and is available in wrap-around termination: 03011 - B | | | | Drawing Termination number (See 3.2.1) 2. APPLICABLE DOCUMENTS 2.1 Government documents.

5、* 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECI

6、FICATIONS * MIL-PRF-32159 - Resistors, Chip, Fixed, Film, Zero Ohm, Industrial, High Reliability, Space Level, General Specification For. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-790 - Standard Practice for Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electri

7、cal Electronic, and Fiber Optic Parts Specifications. MIL-STD-1285 - Marking of Electrical and Electronic Parts. * (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia

8、, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and r

9、egulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-32159 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as

10、 specified in MIL-PRF-32159 and herein (see figure 1). * 3.2.1 Termination material. The termination material shall be in accordance with MIL-PRF-32159 and code letters B, C, D, G, T, or U. * 3.2.1.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and ex

11、ternally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.3 Electrical characteristics. 3.3.1 Temperature range. The temperature range shall be -55C to +125C. 3.3.2 Resistance. The resista

12、nce shall not exceed 0.050 ohm. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03011 REV A PAGE 3 A B C D E 0.60 0.05 0.30 .05 0.23 .05 0.15 .07 0.15 +.05 -0.10 * NOT

13、ES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. The pictorial view of the style above is given as representative of the item. Slight deviations from the outline shown, which are contained within the envelope, and do not alter the functional aspect of

14、 the device, are acceptable. FIGURE 1. Zero-ohm chip resistor style 0201. 3.4 Marking. Marking of the individual chip resistors is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Com

15、mercial and Government Entity (CAGE) code, date, and lot codes. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and

16、 maintenance requirements, and promotes economically advantageous life cycle costs. * 3.6 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-32159 Qualified Products List for at least one part, or perform the group A and

17、 B inspections specified herein on a sample agreed upon by the manufacturer and DSCC-VA. Inches .002 .003 .004 .006 .009 .012 .024 mm 0.05 0.07 0.10 0.15 0.23 0.30 0.60 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS C

18、OLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 03011 REV A PAGE 4 * 3.6.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply. 3.7 Workmanship. Resistors shall be uniform in quality and free from defec

19、ts that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-32159 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Qualification inspection. Qualification inspection is

20、 not applicable to this document. 4.3 Product level qualification. The product level qualification specified in MIL-PRF-32159 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and grou

21、p B inspection (high reliability level only and the parts per million reporting is not applicable) of MIL-PRF-32159. * 4.4.2 Group B inspection. Group B inspection shall be in accordance with MIL-PRF-32159. * 4.4.2.1 Certification. The acquiring activity, at its discretion, may accept a certificate

22、of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.5 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requireme

23、nts of MIL-PRF-32159. * 4.6 Solder mounting integrity. The solder mounting integrity for group B inspection shall be .5 kilograms. 5. PACKAGING * 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel i

24、s to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency

25、, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general

26、 or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended for use in thick or thin film circuits where microcircuitry is intended; also in most surface mount applications. 6.2 Ordering data. The contract or purchase order should specify the foll

27、owing: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. * d. Whether the manufa

28、cturer performs the group B tests or provides certification of compliance with group B requirements (see 4.4.2.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 0301

29、1 REV A PAGE 5 * 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on product

30、s that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Speci

31、fication for Electrodeposited Coatings of Tin). * 6.4 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. These resistors only see a

32、one time pulse (Short-time overload) as part of the group B inspection of MIL-PRF-32159. * 6.5 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the users of record of this document. Requests to be added as a recorded user o

33、f this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.6 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they bec

34、ome available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN 03011-* Vendors similar designation or type number 1/ Vendor CAGE Vendors

35、 name and address Termination styles B RCWP-0201-* SH903 Vishay Dale Electronics PO Box 609 Columbus, NE 68602-0609 Plant: Vishay Israel, Ltd Emek-Sara “B” Industrial Park Beer Sheva, Israel 84874 Termination styles B WAJ 96PG-XXXX 50316 MINI-SYSTEMS, INC. 20 David Road N. Attleboro, MA 02761-0069 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-