DLA AN107401 THRU AN107500 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 250-28《螺栓 耐蚀钢钻孔六角头 6孔 250-28》.pdf

《DLA AN107401 THRU AN107500 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 250-28《螺栓 耐蚀钢钻孔六角头 6孔 250-28》.pdf》由会员分享，可在线阅读，更多相关《DLA AN107401 THRU AN107500 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 250-28《螺栓 耐蚀钢钻孔六角头 6孔 250-28》.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、ANL07LlOL THRU ANLO7500 REV 3 53 W 9497735 000028Ll 2 W c AHSZ800. KAISED OR OEPKESSFO K TO FULL TH .O65 TO POINT .O16 OR CHAHFER SECTION THRU THREAD PROFILE THIS SURFACE HUST BE SQUARE WITH SHANK WITHIN .O03 FULL INDICATOR READINC .O50 / DRILL NO. 50 (.070) CSINK 90 TO .IO0 DIA CHAHFER 30 TO ,438 D

2、IA (OPPOSITE SIDE OPTIONAL) 6 HOLES SPACE0 AS SHOWN WITHIN 020 OF TRUE POSITION PART NO. 1.000 500 ,562 AN107406 AN107401 625 (a) ANLO7408 688 (a) ANI07409 750 (a) ANI07410 812 (a) AN107411 8T5 -125 ANI07412 938 .I88 AN107413 O00 .250 AN107414 062 .2l2 ANI07415 125 .375 AN107516 188 .438 AN107417 25

3、0 .500 AN107418 L 1.312 I. 375 1.438 I. 500 1.562 1.625 1.688 1.750 1.875 2.000 2.J25 2.350 2.375 2. mo K 1.000 - . O60 .562 .625 .688 .750 .e12 .a75 .938 I.000 I. 125 I. 250 I. 375 1.500 1.625 1.750 PART NO ANI 074 19 ANI07420 AN10742 1 AN I07422 AN 107423 AN107424 AN107425 AN I074 26 ANI07427 ANI0

4、7528 AN107429 ANI07430 ANI 0743 I AN107432 (a) THREAD TO HEAD. HAXIHUH TWO IHPERFECT THREADS. L 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 3.000 4.125 4.250 K f. O00 - .b0 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 PART No I AN107433 4.

5、375 AN107434 4.500 AN107435 4.625 ANI07436 4.750 AN107437 4.875 AN107438 5.000 ANI07439 5.125 AN107440 5.250 ANI07441 5,975 ANI07442 5.500 AN107443 5.625 AN107444 5.750 AN107445 5.875 ANI07446 6.000 I K +.o00 -. O60 3.625 3.750 3.875 4.000 4.125 4.250 4.375 6.500 $ .625 6.750 1.875 5.000 1.125 3.250

6、 NOTE: (i) SHANK SHALL BE STRAIGHT WITHIN .O03 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCEHTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATIOK TO THE WASHER FACE DIAHETER AND HEXAGON SHALL BE YITNIN .O13 FIR. PART NO AN10744 AN107441

7、 AN10744 AN107451 ANI 0745 I AN10745: AN10745: AN107451 AU LO1 451 AN10745t AN I 074 57 ANI O1 4 5E AN I O 74 51 AN10746 INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. HATERIAL: CORROSION RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SUEPACE ROUGHNESS: AS107 UANUFACTURING SPECIFI

8、CATION: AUS 7472 )INSPECTION: ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE WITH AHS2645. BREAK SHARP EDGES .O03 - .OIS UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES. DIHENSIONS 22. UNLESS OTHERWISE SPECIFIED: TOLERANCES: LINEAR DIHENSIONS f.O1O. ANGULAR DO NOT USE UNASSI

9、GNED PART NUHBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COHHITTEE OF THE SAE P.A. AIR FORCE-NAVY AERONAUTICAL STANDARD AN I 0740 I Other Cust USAP - 11 Navy - AS Army - AV AN i%OO BOLT - CRES DRILLED HEX HEAD, 6 HOLES, .250-28 Prolect No. 5306-1058 a-rmiloimi l.all4,um,. THIS DOCUMENT CONTAINS I - PAGES. i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-