DLA AN107201 THRU AN107300 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 1 HOLE 750-16《螺栓 耐蚀钢钻孔六角头 1孔 750-16》.pdf

《DLA AN107201 THRU AN107300 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 1 HOLE 750-16《螺栓 耐蚀钢钻孔六角头 1孔 750-16》.pdf》由会员分享，可在线阅读，更多相关《DLA AN107201 THRU AN107300 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 1 HOLE 750-16《螺栓 耐蚀钢钻孔六角头 1孔 750-16》.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、AN107201 THRU AN107300 REV 3 53 m 9377915 0000282 9 m DI BOTH END.T 2.062 .312 2.125 1 -375 PART no AN107206 AN107209 AN107210 AN107211 AN107212 AN107213 AN107215 AN107216 10721 I)- LTHIS SURFACE MUST BE NUARE WITH SHAM( WTTHIN .O03 PIILL INDICATOR RFADINO CHAMPW 30. TO 1.062 DIA (OPPOSITE SIDE OPTI

2、ONAL) +.o00 I -.:o 2.562 .812 e:;% :% 1.000 1.125 3.000 1.250 PART NO. - AA10721 AA10721 AN107219 riio7220 107222 1110722 AN107221 AN10722f AN107225 AN107226 10722 AN107226 AR107229 Ml07230 LI R +.o00 -, 060 3.375 1.625 3.500 3.625 =t f.000 2.250 3:g; 2:E 4.125 2.375 4.250 2.500 4.375 2.625 4.500 2.

3、 50 4.625 I 2.g75 4.750 3.000 5.000 3.250 4075 I 3125 PART no. AN107231 AN107232 AN107233 AN107234 AN107235 AN107236 tA279fS; AN107239 AN107240 AN107241 AN107242 AU10724 AA10724f LI KI PART Na +.o00 5.875 4.125 Mlq251 6.000 4.250 AU107252 (a) THREAD TO HEAD. IUXIHUH TWO IUPERFECT THREADS. NOTE: (I)

4、SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAHETER AND HEXAGON SHALL BE WITHIN .O32 FIR. INACTIVE FOR DESIGN AFTER 27DEC 196

5、6 NO SUPERSEDING STANDARD. HATEPIAL: CORROSION RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SUPPACE ROUGHNESS: AS107 )(AHUFACTUBING SPECIFICATION: AUS7472 IYSPECTION: ALL FARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE WITH AHS2645. DREAK SHARP EDGES .O03 - .O15 UNLESS OTHERW

6、ISE SFECIFIEO. DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERENCES; LINEAR DIHENSIONS 2.010, ANCILAR DIHENSIONS 22. DO NOT USE UNASSIGNED PART NUUBERS. AIR FORCE-NAVY AERONAUTICAL STANDARD AN 10 72.0 I P.A. Ocher Cust USAF - Il Navy - AS Army - AV BOLT - CRES DRILLE0 HEX HEAD, 1 HOLE, .750 - 16 AN I g+300 I I ld GOImWmPRmCIDOlmh l,-l,-S,YK.I Project No. 5306-1056 THIS DOCUMENT CNTANS 1 -. -. - PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-