DLA AN106201 THRU AN106300 REV 3-1986 BOLT-CRES HEX HEAD DRILLED SHANK 625-18.pdf

《DLA AN106201 THRU AN106300 REV 3-1986 BOLT-CRES HEX HEAD DRILLED SHANK 625-18.pdf》由会员分享，可在线阅读，更多相关《DLA AN106201 THRU AN106300 REV 3-1986 BOLT-CRES HEX HEAD DRILLED SHANK 625-18.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、I AN106201 THRU AN106300 REV 3 53 W 7977715 O000272 b W 1.125 1.250 1.186 1.312 1.375 1.438 1.500 1.562 1.625 1.688 L.750 L.812 L.875 .o00 .125 !.250 !.500 !.375 K TO FULL T ( .126-. 133) CSINK BOTH ENDS 60. TO -188 DIA - 2 HOUS ON AXIS 01 THD WITHIN -005. ANGUIAR LOCATION OF THIS (a(0WP AS i UNIT H

2、AY VARY THIS SWPACE MJST BE SQARE KITH SHANK KITHIN .O03 p(TLL IDICAT(R RgADIHO -965 1.090 1.028 1.152 1.215 1.278 1.340 1.402 1.465 1.528 1.590 1.652 1715 1.965 2.090 2.340 i:?!J+o 2.215 =I= I P.A. USAF - II Navy - AS Army - AV Other Cust AIR FORCE-NAVY AERONAUTICAL STANDARD AN I 0620 I BOLT - CRES

3、 HEX HEAD, DRILLED SHANK, .625-18 ANI cg300 - IC +.o00 -.O60 - .125 .188 .250 .312 .375 .438 .500 .562 .688 : 750 .812 .a75 1.000 1.125 1.250 .625 1.375 1.500 - PART no. 106206 10620 106209 106210 106211 106212 106213 106216 106217 106218 106219 106220 mi06221 106222 mi06223 ANi0620g AN106214 AN1062

4、15 Cw 30. TO ,938 DIA . (OPPOSITE SIDE OPTIOHAL) - L - 2.625 22: i?; 3.000 3.125 3.250 3.375 3.500 3.625 3 750 3.875 4.000 4.125 4.250 4.500 4.625 4.375 4.750 4.815 5.125 5.000 +. O00 2.465 1.625 2 * 590 2.715 2.840 2.000 2.965 2.125 3.090 2.250 2.500 3.215 2.375 ;:z:g 2.625 3.590 ;:i; 3.000 3.125 J

5、?:% 3.250 4.215 3.375 4.340 3.500 4.590 3.750 4.465 3.625 PART HO. AN106224 106225 106226 AN10622 AN10622g 106229 AN106230 AN106231 AN106232 AN106233 ANID6234 AN106235 AN106236 AN10623 AN10623g AN106239 AN106240 AN106241 AN106242 - L 5.250 5.375 5.500 5.625 3; 6.000 FRLY - PMIT HO. 4.625 AN106248 1

6、4 50 I AR106249 5.715 4:&5 AN106250 NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER PACE DIAMETER AND HEXAGON SHALL BE WITHIN .O28 FIR. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. / . THIS DOCUMENT CONTAINS 1 .- PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-