DLA AN105601 THRU AN105700 REV 3-1986 BOLT CRES HEX HEAD DRILLED SHANK 250-28.pdf

《DLA AN105601 THRU AN105700 REV 3-1986 BOLT CRES HEX HEAD DRILLED SHANK 250-28.pdf》由会员分享，可在线阅读，更多相关《DLA AN105601 THRU AN105700 REV 3-1986 BOLT CRES HEX HEAD DRILLED SHANK 250-28.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、ANL05b01 THRU ANI105700 REV 3 53 W 7777735 00002bb O P.A. USAF - II Other Cust Navy - AS Army - AV AIR FORCE-NAW AERONAUTICAL STANDARD AN 1 0560 1 BOLT - CRES HEX HEAD, DRILLED SHANK, .250-28 ANI y700 FED. SUP CLASS I 5306 ATERIAL IDENTIFICATION PER r“ AH92800. RAISED OR DEFRESSED .O10 MAX .156 - TH

2、IS StRFACE HST BE SQUARE WITH SHAAIC YITM .O03 FULL IHDICATtR READInO CSIhX BOTH ENDS 2 HOLES ON AXIS OF THD WITHIN .005. ANGULAR UCATIN OF THIS CROUP AS A UNITHAY VARY 60 TO .loo DIA CHAMFER 30 TO .438 DIA (OPPOSITE SIDE OPTIONLL) - n +.o00 - .o60 tl I3 .125 * 188 .250 .312 .375 .438 .500 .562 .625

3、 .688 *750 .812 .815 .938 1.000 1.062 - - L - 1 - 750 1.875 2. GOO 2.125 2.250 2.375 2.500 2. 625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 - A 1.640 i: 6% 2.015 2.265 2.140 2.390 2.515 2.640 2.765 2.890 3.015 3.140 3.265 3- 390 3.515 3.640 3.765 3.890 4.015 4.140

4、 T - X -. 060 +.o00 - 3; 4.000 4.125 4.250 4.500 4.625 4.750 4.375 ;:“o 5.125 5 - 250 5.375 L .500 .562 .688 .750 .a12 .875 .938 .6S 1.000 1.062 1.125 1.188 1.250 1.312 ;: 2B 1.500 1.562 1.688 1.625 A - -390 - 452 512 : 220 :B .TO2 .e90 - 952 1.015 1.078 1.140 1.202 1.265 1.328 1.452 1.5fi 1.578 1 3

5、90 - PART 10. PART AO. K +. O00 -.OC% - 1.125 1.250 1.375 1.500 1.625 1.750 2.000 2.125 2 -250 2.375 2.500 1.875 2.625 :g; 3.000 3.125 3.250 3.375 3.500 3.625 PART no. AN105626 AN:$% AN105629 AN105630 AN105631 AN105632 AN105632 AN10563 AN105635 AN105636 AN105637 AN105639 AN1056110 AN105642 AN105643

6、AN105694 AN105645 ANi056A6 N105638 105641 AN105647 AN105648 AN105649 AN105650 AN105652 AN105653 AX105654 AN105655 AN105656 AN105657 AN105658 AN105659 AN105660 105651 4.375 4.265 4.625 4.515 4 50 4.640 5.000 5.125 5.015 5.250 5.140 5.375 5.265 5.500 5.390 5.625 5.515 .750 5.640 4.500 4.390 4375 na105

7、606 105608 105610- 105612 AN105607 AN105609 AN105611 AN105613 AN105614 AN105615 105616 AN 1 o 5 6 1 ANi056ig 105620 AN105619 AN105621 AN105622 AN105623 AN105624 AN105625 5-875 5.765 6.000 5.890 (a) THREAD TO HEAD. HAXXHUH TWO IHPERFECT THREADS. NOTE: (1) SHANK SHALL BE STRAIGHT WITHIN .O03 FIR. PER

8、INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAB PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAHETER AND HEXAGON SHALL BE WITHIN .O13 FIR. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. HATERIAL: CORROSI

9、ON RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 HANUFACTURING SPECIFICATION: AUS 7172 ) INSPECTION: ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE WITH AHS2645. BREAK SHARP EDGES .003-.O15 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIHENSIONS 2.010. ANGULAR DIHENSIONS 12. I I Project No. 5306-1040 -1. uvpILuxT Fmnmmc 0.m.: ,*l.ll,.I,YI,*, / . THIS DOCUMENT CONTAINS . PAGES. ; Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-