DLA AN104901 THRU AN105000 REV 3-1986 BOLT - CRES HEX HEAD 375-24.pdf

《DLA AN104901 THRU AN105000 REV 3-1986 BOLT - CRES HEX HEAD 375-24.pdf》由会员分享，可在线阅读，更多相关《DLA AN104901 THRU AN105000 REV 3-1986 BOLT - CRES HEX HEAD 375-24.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、ANZOV701 THRU AN305000 REV 3 53 W 7777735 0000253 3 MATERIAL IDENTIFICATIOH PER AMS 2800. RAISED OR DEPRESSED r .O10 MAX .219 SECTION THRU THREAD PROFILE .I50 . O90 CTHIS SURFACE MUST BE SQUARE WITH SHANK WITHIN .O03 FULL INDICATCR READING CHAMPER 30 TO .562 DIA . (OPPOSITE SIDE OPTIONAL) K L - 1.50

2、0 1.625 1.688 1.562 3; 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2. a75 K +.o00 - .o60 :BE * 875 * 938 1.000 1.125 1.250 1.625 1 - 375 1.500 1.750 1 * 875 2.000 2.1.25 L - 4.750 4 * 875 5000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 P:JT NO AN104941 AN10494 AN104941 AN10494! AN104951 AN10495:

3、AN10495: AN10495: AN104951 AN104955 AN10495t PART NO. AN104918 AN104920 AN104922 AR104923 AN104924 AN104925 AN104926 AN10492 AN10492g AN104929 AN104930 AN104931 104919 nrno492i L 3.000 3- 125 3.250 3.375 3.500 3.625 ;:i; 4.000 4.125 4.250 4.500 4.625 4.375 PART NO. AN104932 AN104933 AN104934 AN10493

4、5 AN104936 AN104937 AN104939 AN104940 AN104941 AN104942 AN104943 AN104944 AN104945 10493a K +. O00 - , O50 4.000 4.125 4.250 4.500 4.625 4.375 4 * 750 4.875 5.000 5.125 5.250 K +. O00 - .O60 2.250 2.625 2 - 375 2.500 2.750 2 - 875 3.000 3.125 3 * 250 3.375 ;:% 3 - 750 3. a75 PART NO. L = -750 .812 *

5、 875 - 938 1.000 1.062 1.125 1.188 1.250 1.312 1.375 i. 438 (a) I AN104906 .25O AN104910 .3i AN104911 .375 I AN104912 .43a 104913 .500 AN104914 .562 AN104915 .625 AN104916 .688 AN104917 I (a) THREAD TO HEAD. MAXIMIIM TWO IMPEFECT THREADS. SHANK SHALL BE STRAIGHT WITHIN ,0025 FIR.PER INCH OF BOLT LEN

6、GTH THE CONCEWiRICIT OF THE 3K IN REUTION TO THE WAS= FACE DUME?ER AND HEXAGON THE CONCECiRICITY OF THREAD PD IN REUTION TO THE SHANK SHALL =WITHIN .o06 FIR. SHALL BE WITHIN .o17 FIR. MATERIAL: CORROSION RESISTAIIT STBEL - SEE KKIANUPACTURING SPECIFICATION SWFACE ROUGHNESS: AS107 MAlFACTRING SPECIFI

7、CATION: AM3 74-72 INSPECTION: ALL PARiS SHALL UNERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCE WITH AMS2645. BREAK SP EDGES .003-.015 mass OTHWWISE SPECIFIED. DIMEnSIOAS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLWANCES; LINEAR DIMWSIONS f.O1O, ANGULRR DIMENSIONS f2 DO HOT USE WSSIGED PART “IS.

8、TM3 STANDARD HAS DEVELOPED COOPERATIVELY WITH THE ENGIm AND PROPELLKR UTILITY PARTS COMMirPEE OF THE SAE. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. AIR FORCE-NAVY AERONAUTICAL STANDARD .t. AN I 0490 I USAF - ll WVY - As - 4v AN I83000 hm cut BOLT - CRES HEX HEAD .375-24 I I Project NO. 5306-1033 GOVEflNYENT PAMTNC O ICE. 1967-25b515/391g -? K THIS DOCUMENT CONTAINS I PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-