DLA AN104801 THRU AN104900 REV 3-1986 BOLT - CRES HEX HEAD 3125-24.pdf

《DLA AN104801 THRU AN104900 REV 3-1986 BOLT - CRES HEX HEAD 3125-24.pdf》由会员分享，可在线阅读，更多相关《DLA AN104801 THRU AN104900 REV 3-1986 BOLT - CRES HEX HEAD 3125-24.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、MATERIAL IDENTIFICATION PER IMPERFECT THD SEGTION THRU THREAD PROFILE .i501 .o90 L .625 .688 :E ,875 .938 1.000 1.062 1.188 1.125 1.250 1.312 AN10484 I AN10480g .125 AN104809 .188 AN104810 .250 AN104811 .312 AN104812 I .375 AN104813 .500 AN104815 .438 N104814 AN104816 .625 AN104817 -562 I LTHIS SURF

2、ACE MUST BE SQUARE WITH SHANK WITHIN .O03 FULL INDICATOR READING L 1.375 1.438 1.500 1.562 1.625 1.688 1 - 750 1.875 2.000 2.125 2.375 2.250 2.500 2.625 CWR7 30 TO .WO DIA (OPPOSITE SIDE OPTIONAL) Y +. O00 .688 AN104818 .750 AN104819 .812 AN104820 .875 AN104821 .938 AN104822 1.000 AN104823 i. 062 AN

3、104824 1.188 AN104825 1.312 AN104826 1.438 AN104827 1.562 AN104828 1.688 AN104829 1.812 AN104830 1.938 AN104831 - L = 2 - 750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 %:E 4.125 4.375 4.2 50 K +. O00 - .o60 2.062 2.188 2.312 2.438 2.562 2.688 2.812 2.938 3.062 3.188 3 - 312 3.438 3.5Q 3.688 K

4、+. O00 -. 060 - 3.812 4.062 4.188 4.312 4.438 4.562 4.688 4.812 4.938 5.06e 5.188 5 * 312 3.938 PART NO - AN104846 AN10484 AN104841 AN104849 AN104850 AN104851 AN104852 AN10485: AN104854 AN104855 AN104850 AN104857 AN10485E (a) THREAD TO HEAD. MAXIMUM TWO IMPERFECT THREADS. NOTE: (i) SHANK SHALL BE ST

5、RAIGHT WITHIN .OD3 FR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .o06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN .O15 FIR. HATEZlIAL: CORROSION RESISTAET STEEL - SEE MANUFACTUR

6、ING SPECIFICATION 3tWACE ROUGHNESS: AS107 HAFACTURRIG SPECFICATION: AM9 7472 iNCPCCTIOH: ALL PARTS SAALL UIIDCRGO ?LUORCSCCIIT IRSPCCTIOR IR ACCORDANCE HITA AUS2645 BREAK SHARP EDGES .003-,015 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIMENSIONS

7、 f.010, ANGULAR DIMENSIONS 2. DO NOT USE UNASSIGNED PART NUMBERS. INACTIVE FOR NEW DESIGN AFTER 27DEC 1966 NO SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. ?.A. AIR FORCE-NAVY AERONAUTICAL STANDARD AN 104801 Other Cust USAP - 11 Arwy-AV Wavy-AS BOLT - CRES HEX BEAD .3125-24 AN i%oo I THIS DOCUMENT CONTAINS . -I- PAGES. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-