DLA AN102301 THRU AN102400 REV 3-1986 BOLT - HEX HEAD DRILLED SHANK 4375-20.pdf

《DLA AN102301 THRU AN102400 REV 3-1986 BOLT - HEX HEAD DRILLED SHANK 4375-20.pdf》由会员分享，可在线阅读，更多相关《DLA AN102301 THRU AN102400 REV 3-1986 BOLT - HEX HEAD DRILLED SHANK 4375-20.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、 -_ - 1- -iTHRU ANZOZYOO REV 3 53 U 7777735 000023Y 7 ”- E. I SECTION L .e12 .e75 .938 1.000 1 .o62 1.125 1.186 1.250 1.312 :a 1.500 1.562 1.625 1.688 1.750 1.875 2.000 P A - .672 .735 .798 . a50 .922 .985 1 .o48 1.110 1.172 1.235 1.298 1.360 1. 422 1. 485 1.548 1.610 ;:E - .4375-20UNP-3Al SPEC MIL-

2、S-7742 / CHAMFER 30 TO .625 DIAJ (OPPOSITE SIDE OPTIONAL) 1 PROFILE THIS SURFACE MUST BE SQUUARE WITH -SHANK WITHIN .o03 FIR. K + . O00 - -060 13 .125 .i88 .250 .312 :i% .500 .562 ,625 .688 *750 .a12 ,875 .938 1.062 1.188 2.125 2.250 2.375 AN102306 /I 2.500 AN102307 2.625 AN102308 2.750 mi02309 AN10

3、i310 11 ;:o AN102311 3.125 AN102315 3 i 625 AN1.02316 I/ 3.750 AN102317 3.875 Ui102321 4.375 U102322 /I 4.500 WO2323 4.625 A 1.985 2.110 2.235 2.360 2.485 2.610 2.735 2.860 2.985 3.110 3 235 3.360 3.485 3.610 3.735 3 .MO 3.985 4,110 4.235 4.360 4.485 K + . ooa - .O60 i .312 1.438 i:562 1.688 1 .812

4、1 ;938 2.062 2.188 2.312 2.438 2.562 2.688 2.812 2.938 3.062 3.188 3.312 3.438 3.562 3.688 3.812 AN102324 4.750 AN102325 II 4.875 AN102326 5.000 AN102327 5.125 AN102328 11 5.250 AN102329 5.375 5.500 5.625 AN102332 5.750 / AN10233 5 .875 AN10233: 6 .O00 AN102335 AN102336 AN102337 AN102338 A - 4.610 4

5、 .60 4.735 4.985 5.110 5.235 ; :i:; 5.610 5.735 5.860 UNIT MAY VARY FREELY K +.ow -.o60 $938 . o62 4.188 4.562 4.8 4 .812 4.938 5.062 5.188 PART NO. AN102345 AN1023b6 AN102347 AN102348- AN102349 AN102350 AN102351 AN10235Z AN102353 AN102354 AN102355 (a) THREAD To HEAD. IuxIwuE( WO IMPERFECT WEADS. SH

6、ANK SHALL BE STRAIGHT WITHIN .O025 FIR.PER INCH OF BOLT LENGTH. ME CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN ;O06 FIR. THE CONCENTRICITY OF THE SHANK IN RELATION TO !CHE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN .O19 FIR. AATWIAL: STEEL AMS6322 FINISH: CADMIUM PLATE

7、AMs2400 SURFACE ROUCHNESS-i AS107 “FAC”RIN0 SPECIFICATION: AMs7452 INSPECTION ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AM52840 HARDNESS: ROCKWELL C26-32 BRGAR SHARP BWES DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANdEs; LINEAR DIMENSIONS t.O1O, ANGULAR - DO NOT USE

8、UNASSIGNED PART ”BERS. .003-.015 UNLESS OTHERWISE S-PECIFIED. DIMENSIONS f2. INACTIVE FOR NEW DESIGN AFTER 3 MARCH i969 NO SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILIT PARTS COMMITTEE OF THE SE, 1 AIR FORCE-NAVY AERONAUTICAL STANDARD I AN102301 A. Ar-II -1 I TURI1 . - - 1 AN102400 IST. NAVY-A3 BOLT - HEX HEAD, DRILLED SHANK, .4375-20 ARMY-AV/ THIS DOCUMENT CONTAINS I PAGES. - Project N0.5306-1008 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-