DLA AN101701 THRU AN101800 REV 3-1986 BOLT - HEX HEAD 625-18 (INACTIVE AFTER 3 MAR 1969).pdf

《DLA AN101701 THRU AN101800 REV 3-1986 BOLT - HEX HEAD 625-18 (INACTIVE AFTER 3 MAR 1969).pdf》由会员分享，可在线阅读，更多相关《DLA AN101701 THRU AN101800 REV 3-1986 BOLT - HEX HEAD 625-18 (INACTIVE AFTER 3 MAR 1969).pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、ANLOL70L THRU ANLOLBOO REV 3 53 W 7977735 0000229 5 W T-i?-Q PED. SUP CLASS. ,5306 - L O .344 K TO FULL THD -.O16 OR CHAMFER I- .120f. 030 DIA MIN .625-18UNF-3A SPEC MIL-S-7742 THIS SURFACE MUST BE SQUARE WITH SHANK WITHIN .003FIR. LCHAER 30“ TO .938 DIA (OPPOSITE SIDE OPTIONAL) SECTION THRU THREAD

2、PROFILE I PmT No. 11 L L 1.812 1.875 2.000 1.125 .i25 101706 2.125 1.250 .250 101708 2.375 11375 .375 AN10171o 2.625 1.500 .500 AN101712 2.875 1.562 .562 AN101713 3.000 1.625 .625 AN101714 3.125 1.750 .750 AN101716 3.375 1.188 .i88 AN101707 2.250 1312 .312 AN101709 2.500 1.438 .438 AN101711 2.750 1.

3、688 .688 AN101715 3.250 1.125 101720 3.875 2.875 AN101734 1.250 AN101721 4.000 3.000 AN101735 1.375 101722 4.125 3.125 101736 1.625 AN101724 4.375 3.375 101738 1.500 AN101723 4.250 3.250 AN101737 1.750 AN101725 4.500 3.500 AN101739 1.875 AN101726 4.625 3.625 AN101740 2.000 AN101727 4.750 3.750 AN101

4、741 2.125 AN101728 4.875 3.875 AN101742 2.250 AN101729 5.000 4.000 AN101743 2.375 AN101730 5.125 4.125 AN101744 - L 5.250 5.375 5.500 5.625 5 e750 5.875 - 6.000 4.625 4.750 4.875 5.000 AN101748 AN101749 AN101750 AN101751 SHANK SHALL BE STRAIGHT WITHIN .O02 FIR.PER INCH OF BOLT LENGTH. THE CONCENTRIC

5、ITY OP THREAD PD IN RELATION. TO THE SHANK SHALL BE WITHIN .o06 FIR. THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN .O28 FIR. MATERIAL: STEEL AMs6322 HARDNESS: ROCKWELL C20-32 FINISH: CADMIUM PLATE AMs2400 SURFACE ROUGHNESS: AS107 HANUFACTITRING SP

6、ECIFICATION : AMs7452 BREAK SHARP EDQES .003-.015 UNLESS OTHERWISE SPECIFIED. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: D INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AM82640. TOLERANCES; LINEAR DIMENSIONS f.010, ANGULAR DIMENSIONS f2. DO NOT USE UNASSIGNED PART

7、 NUIBERS. INACTIVE FOR NEW DESIGN AFTER 3 WQI 1969 NO SUPERSEDING STANDARD. THIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. AIR FORCE-NAVY AERONAUTICAL STANDARD BOLT - HEX HEAD .625-18 ANI01 701 ANIOI 800 P!A. AF-II THRU CUST. NAVY- AS THIS DOCUMENT CONTAINS PAGES. 5306-1002 I u I c , j P 6 i ! L E s : ! i O l I f Licensed by Information Handling Services