DLA A-A-59926-2013 BARBED TAPE CONCERTINA (NON-REINFORCED LONG BARB).pdf

《DLA A-A-59926-2013 BARBED TAPE CONCERTINA (NON-REINFORCED LONG BARB).pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59926-2013 BARBED TAPE CONCERTINA (NON-REINFORCED LONG BARB).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND A-A-59926 6 June 2013 COMMERCIAL ITEM DESCRIPTION BARBED TAPE, CONCERTINA (NON-REINFORCED LONG BARB) The General Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE. This Commercial Item Description (CID) covers concertina

2、 barb tape for barb tape entanglements. These entanglements may serve as a security barrier for confinement applications, nuclear generating plants, petroleum/chemical storage, refineries, sensitive areas at airports and nuclear weapons storage, etc. 2. SALIENT CHARACTERISTICS. 2.1 Material. The con

3、certina barbed tape shall be made of stainless steel (SS) per ASTM A666, 300 Series and shall be subject to all provisions of this CID. 2.2 Design and construction. Concertina barbed tape furnished under this CID shall conform to the dimensions and design characteristics as specified herein, in Figu

4、re 1 and in Table I. Tape material (barb) shall be single coil non-reinforced 30 inch diameter and fabricated from 0.025 inch thick 300 Series SS that is 1.21 inch wide prior to forming. Each roll shall consist of 101 coil loops with pairs of loops alternately spot welded together at 5 locations aro

5、und the circumference. Concertina welds shall be capable of withstanding a minimum pull load of 400 lbs. Cluster of 4 needle sharp barbs shall be located 4 inch on center along the spiral turns. The barb length shall be 2.250 to 2.600 inch tip to tip and alternately offset 0.15 0.45 inch. FIGURE 1.

6、BARBED TAPE. Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia, ATTN: DSCP-NASA, 700 Robbins Avenue. Philadelphia, PA 19111-5096 or e-mail to dscpg&ispecommentsdla.mil. Since contact information can change, you may want to verify the curre

7、ncy of this address information using the ASSIST Online database at https:/assist.dla.mil. ASMC N/A FSC 5660 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59926 2 TABLE I. Dash Numbers and Design Characteristics. Dash No. Description Dia. inch

8、Coil Loops Strip Material Strip Cable Welds Coil Spacing inch Coil Yield feet Pkg. ASTM F 1910 Item # 1 Single Coil Concertina Rapid Deployment 30 101 SS 1 5 12 50 7/box #25 3. REGULATORY REQUIREMENTS. 3.1 The offerer/contractor is encouraged to use recovered materials to the maximum extent practica

9、ble, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, s

10、tandards, and the quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5. PACKAGING. 5.1 Preservation, packing and marking shall be as specified in the contract or order. 6. NOTES. 6.1

11、Unless otherwise specified, all dimensions are in inches. 6.2 Unless otherwise specified in the contract or purchase order, packaging shall be in accordance with ASTM D3951. 6.3 The following part or identification numbering procedure is for government purposes and does not constitute a requirement

12、for the contractors. The part number identification number (PIN) shall consist of the basic commercial item description number followed by a dash number from Table I. Example: AA59926 - 1 Dash number Basic number 6.4 Source of documents. 6.4.1 FAR. The FAR may be obtained from the Regulatory Secreta

13、riat, 1800 F Street NW, Washington DC 20405 or online at http:/www.acqnet.gov. 6.4.2 ASTM Standards. Copies of ASTM standards may be obtained from the ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at http:/www.astm.org. 6.5 Ordering data. The contract or order

14、 should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59926 3 6.6 Key words. Coil loops Entanglements Security B

15、arrier MILITARY ACTIVITIES: CIVIL AGENCY COORDINATING ACTIVITY: GSA FAS Custodian: Army AT Preparing activity: Navy YD DLA IS Air Force 99 (Project 5660-2013-004) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-