DLA A-A-59840 A-2009 WEBBING MOUNTAINEERING.pdf

《DLA A-A-59840 A-2009 WEBBING MOUNTAINEERING.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59840 A-2009 WEBBING MOUNTAINEERING.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 A-A-59840 29 October 2009 COMMERCIAL ITEM DESCRIPTION WEBBING, MOUNTAINEERING This commercial item description is approved for use by the Defense Supply Center, Philadelphia and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE. This commercial item descrip

2、tion covers the requirements for mountaineering webbing and sewn slings which are generally used to connect rock and ice protection to the climbers rope for safety. 2. CLASSIFICATION. The webbing will be furnished in the following types and sizes: 2.1 Types Type I Sewn Sling Type II Webbing, Textile

3、, 1- inch Type III Sewn Sling, Load Limiting 2.2 Sizing. The webbing Type I will be available in three sizes as described in Table I. Types II and Types III will be available in one size only. 3. SALIENT CHARACTERISTICS. The sewn sling shall be as light-weight as possible, while meeting the standard

4、s described in 3.1.1, 3.1.2 and 3.1.3 and the physical characteristics of Table I. Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP Standardization Team, 700 Robbins Avenue, Philadelphia, PA

5、 19111-5096. Since contact information can change, you may want to verify the currency of this address information using Acquisition Streamlining and Standardization Information System (ASSIST) online database at http:/assist.daps.dla.mil/ . AMSC N/A FSC 8305 METRIC Provided by IHSNot for ResaleNo r

6、eproduction or networking permitted without license from IHS-,-,-A-A-59840 2 TABLE I. Physical characteristics (Types I and Type III) Type & Size Length, cm Width, mm Type I Size I 30 18 Type I Size II 60 18 Type I Size III 120 18 Type III 228 25 3.1 Types. 3.1.1 Type I. The Type I sewn sling shall

7、be constructed of nylon and conform to the dimensions of Table II and the requirements in drawing 3-3-0132. All ends of the sewn sling shall be cut with a hot knife to prevent fraying. The sewn sling design shall provide ease of use with typical combat gloves while meeting the standards in this desc

8、ription. 3.1.2 Type II. The Type II webbing shall be nylon and conform to MIL-W-5625, 1-inch (see 7.3) and the requirements of drawing 3-3-0140. The color shall be a good match to Foliage Green 502/504. 3.1.3 Type III. The Type III sewn sling shall be constructed of nylon and conform to the dimensio

9、ns of Table I and the requirements in drawing 3-3-0130. All ends of the sewn sling shall be cut with a hot knife to prevent fraying. The sewn sling design shall provide ease of use with typical combat gloves. The sewn sling shall be of an energy absorbing design. It shall be designed to begin extend

10、ing after 2 kiloNewtons of force is placed on it. Energy absorption shall be accomplished during the extension of the webbing and tearing of internal stitching not integral to the overall strength of the sewn sling. The sewn sling shall have fixed clip in points at the top and bottom that will fit a

11、ny typical carabiner in accordance with A-A-59836. 3.2 Color (Types I and Types III only). The sewn slings shall provide low contrast with typical use terrain and be a good match to the colors in Table II. TABLE II. Color for sewn slings (Types I and Type III) Type Size Color I I Desert Sand 500/503

12、 I II Gray 26270 I III Foliage Green 502/504 III N/A Foliage Green 502/504 3.3 End Item Testing. The webbing shall meet the following standards for the International Mountaineering and Climbing Federation Union Internationale des Associations dAlpinisme - (UIAA) as listed below in Table III. Provide

13、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59840 3 TABLE III. End item testing (All Types) Types UIAA Standard Type I 104 Type II 103 Type III 104 3.4 Labels Each webbing for all types shall have identification label (Class 1) a size label (Class 2

14、) and instruction label (Class 3) or a combination size, identification and instruction label (Class 14) conforming to Type VI of MIL-DTL-32075. The color of the labels shall be white. Size and instruction information details will be in accordance with Union Internationale des Associations dAlpinism

15、e (UIAA) standards 103 and 104. The following identification information shall be included in the printing for the labels for the webbing. WEBBING, MOUNTAINEERING TYPE (I, II, or III) NSN: 8465-00-268-2455 3.5 Workmanship. The finished webbing (all types), mountaineering shall conform to the quality

16、 of product established by this document. The occurrence of defects shall not exceed the contractors own quality assurance standards and the quality assurance standards defined in the technical data in the solicitation and/or contract. 3.6 Service life. The webbing and sewn slings shall have no unex

17、pected material or component failures during a continuous one-year cycle. The webbing sewn slings shall have no unexpected material or component failures during periodic use over a five year period. 3.7 Labels/barcoding/instruction slip. If applicable, all labeling, barcoding and instruction slip re

18、quirements shall be as specified in the solicitation or contract (see 7.2). 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.1 Recycled, re

19、covered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle cos

20、ts. 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, Provided by IHSNot for ResaleNo reproduction or networking permitted wit

21、hout license from IHS-,-,-A-A-59840 4 and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance. 5.2 Visual examination. Each webbing shall be examined for the following defects as l

22、isted in Table IV. TABLE IV. End item examination Examine Defect Description Finish Not smooth and adherent Not low reflectance matte finish Does not provide low contrast with typical use terrain Color Not as specified Size Not as specified Labels/barcoding/instruction slip (if applicable) Incorrect

23、, illegible, omitted or misplaced Marking Omitted, missing information or illegible 5.3 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order (see 7.2). 6. PACKAGING. 6.1 Preservation, packing and marking. The preservation, packing and marking shall be as s

24、pecified in the contract or order (see 7.2). 7. NOTES. 7.1 Sources of documents. 7.1.1 Government documents. Copies of Government documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia,

25、PA 19111-5094. DRAWINGS U.S. ARMY NATICK SOLDIER CENTER 3-3-0132 Webbing, Mountaineering, Type I 3-3-0140 Webbing, Mountaineering, Type II 3-3-0130 Webbing, Mountaineering, Type III (Copies of drawings are available from the U.S. Army Natick Research Development and Engineering Center, Natick Soldie

26、r Center, ATTN: NSRDEC-RDNS-WPW-C, Natick, MA 01760) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59840 5 7.1.2 Federal Acquisition Regulations are available online at http:/acquisition.gov/far/index.html or by contacting the Superintendent of

27、 Documents at 202-512-1800. 7.1.3 Non-Government documents. Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents may be available in or through libraries or other informational services. INTERNATIONAL

28、MOUNTAINEERING AND CLIMBING FEDERATION UNION INTERNATIONALE DES ASSOCIATIONS DALPINISME (UIAA) UIAA Safety Standard 103 Mountaineering and Climbing Equipment, Tape UIAA Safety Standard 104 Mountaineering and Climbing Equipment, Slings (Copies are available online at http:/www.theuiaa.org or from the

29、 Union Internationale Des Associations DAlpinisme (UIAA) Monbijoustrasse 61 Postfach CH-3000 Bern 23 Switzerland) 7.2 Ordering data. The contract or order should specify the following: a. Title, number, and date of this Commercial Item Description. b. Type, size and color required (see 2.1, 2.2 and

30、3.2). c. When required, labeling, barcoding, and instruction slip (see 3.7) d. Acceptance criteria (see 5.3). e. Packaging (see 6.1). 7.2 National stock numbers (NSN): Webbing Textile Nylon 1-inch: NSN 8305-00-268-2455 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Custodian: PREPAR

31、ING ACTIVITY: Army-GL DLA-CT Marine Corp-MC Project 8305-2009-004 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at http:/assist.daps.dla.mil/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-