DLA A-A-59739 A-2013 COIL RF CHIP FIXED HIGH Q MINIATURE SURFACE MOUNT.pdf

《DLA A-A-59739 A-2013 COIL RF CHIP FIXED HIGH Q MINIATURE SURFACE MOUNT.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59739 A-2013 COIL RF CHIP FIXED HIGH Q MINIATURE SURFACE MOUNT.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be addressed to: DLA Land and Maritime, Columbus, ATTN: VAT, P.O. Box 3990, Columbus OH 43218-3990, or email (transformersdla.mil ). Since contact information can chan

2、ge you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 5950 A-A-59739A 5 December 2013 SUPERSEDING A-A-59739 25 October 2002 COMMERCIAL ITEM DESCRIPTION COIL, RF, CHIP, FIXED, HIGH Q, MINIATURE, SURFACE MOUNT The Gene

3、ral Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers the general requirements for a radio frequency coil. Coils covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION. This

4、 CID uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see 7.1). AA59739 - 001 F T CID number Dash number (see table I) Inductance Tolerance (see table II) (Optional) Termination finish (see table III) 3. SALIENT CHARACTERISTICS

5、. 3.1 Interface and physical dimensions. Coils supplied to this CID shall be as specified herein. (see figure 1). 3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I. 3.3 Weight. The weight shall be no greater than 0.5 gram maximum. 3.4 Operating temperat

6、ure range. The operating temperature range is 40C to +125C. 3.5 Temperature rise. DC current rating for a 15C rise. 3.6 Altitude. The maximum altitude is 70,000 feet. 3.7 Marking. Coils supplied to this CID shall be marked with the manufacturers standard commercial PIN. 3.8 Pure tin. The use of pure

7、 tin, as an underplate or final finish is prohibited both internally and externally. Tin content of transformer components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass. 3.9 Recycled, recovered, or environmentally preferable materials

8、. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. INCH-POUNDProvided by IHSNot for ResaleNo re

9、production or networking permitted without license from IHS-,-,-A-A-59739A 2 3.10 Workmanship. Coils shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. Dimension Inches mm A B C D E F G H I J .115

10、 Max .110 Max .080 Max .020 Ref .080 .020 .060 .100 .040 .050 2.92 Max 2.79 Max 2.03 Max 0.51 Ref 2.03 0.51 1.52 2.54 1.02 1.27 NOTES: 1. Dimensions are in Inches. 2. Metric equivalents are listed for general information only. FIGURE 1. Configuration and dimensions. Provided by IHSNot for ResaleNo r

11、eproduction or networking permitted without license from IHS-,-,-A-A-59739A 3 TABLE I. Electrical characteristics. CID dash number AA59739- Inductance(nH) Tolerance (%)Q Min SRF Min (GHz) DCR Max (OHMS) IDCMAX (A) 001* 3.0 50 MHz 5 70 1500 MHz 8.10 0.04 1.6 002* 4.1 50 MHz 5 75 1500 MHz 6.20 0.05 1.

12、6 003* 7.8 50 MHz 5 75 500 MHz 3.80 0.05 1.6 004* 10 50 MHz 5, 2 60 500 MHz 3.60 0.06 1.6 005* 12 50 MHz 5, 2 70 500 MHz 2.80 0.06 1.5 006* 18 50 MHz 5, 2, 1 62 350 MHz 2.70 0.07 1.4 007* 22 50 MHz 5, 2 62 350 MHz 2.05 0.07 1.4 008* 33 50 MHz 5, 2 75 350 MHz 1.70 0.09 1.3 009* 39 50 MHz 5, 2 75 350

13、MHz 1.30 0.09 1.3 010* 47 50 MHz 5, 2, 1 75 350 MHz 1.45 0.12 1.2 011* 56 50 MHz 5, 2, 1 75 350 MHz 1.23 0.12 1.2 012* 68 50 MHz 5, 2, 1 80 350 MHz 1.15 0.13 1.1 013* 82 50 MHz 5, 2 80 350 MHz 1.06 0.16 1.1 014* 100 50 MHz 5, 2 62 350 MHz 0.82 0.16 1.0 015* 36 50 MHz 5, 2 65 350 MHz 1.40 0.09 1.3 TA

14、BLE II. Inductance tolerances Code Tolerance (percentage) F G J 1 2 5 TABLE III. Termination finish. Code Termination finishLeave blank L T Tin-lead RoHS compliant, silver-palladium-platinum-glass-frit RoHS, tin-silver-copper (95.5/4/0.5) Provided by IHSNot for ResaleNo reproduction or networking pe

15、rmitted without license from IHS-,-,-A-A-59739A 4 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Prod

16、uct conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to requir

17、e proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the product to be provided under this CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 2 ye

18、ars. b. The company must have sold 1,000 units meeting this CID in the commercial marketplace over the past 2 years. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial pr

19、oducts to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection

20、 Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals is available on their website at http:/www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at the following EPA site: http:/www.epa.gov/epaoswer/hazwaste/minimize/. Included i

21、n the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory contr

22、ol, and submission of these coils to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (Copies of these documents are available online at www.acquis

23、ition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.) 7.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may oc

24、cur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to i

25、nhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 7.6 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance

26、 provisions. c. Packaging requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59739A 5 7.7 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial

27、products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manu

28、facturers shown.) MFRs CAGE MFRs name and address 02113 Coilcraft Inc 1102 Silver Lake Road Cary, Illinois 60013-1658 Phone number (847) 639-2361 Uniform Resource Locator (URL): 7.8 Part number (P/N) supersession data. This CID supersedes the following manufacturers P/Ns as shown. This information

29、is being provided to assist in reducing proliferation in the government inventory system. TABLE II. P/N supersession data. 1/ CID dash number (see table I) AA59739- Vendor commercial PIN CAGE 02113 2/ 001* 1008HQ-3N0XJL* 002* 1008HQ-4N1XJL* 003* 1008HQ-7N8XJL* 004* 1008HQ-10NX*L* 005* 1008HQ-12NX*L*

30、 006* 1008HQ-18NX*L* 007* 1008HQ-22NX*L* 008* 1008HQ-33NX*L* 009* 1008HQ-39NX*L* 010* 1008HQ-47NX*L* 011* 1008HQ-56NX*L* 012* 1008HQ-68NX*L* 013* 1008HQ-82NX*L* 014* 1008HQ-R10X*L* 015* 1008HQ-36NX*L* 1/ When “*“ is used for coded values, its the contractors responsibility to select those options al

31、lowed by the CID. 2/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. 7.9 Government users. To acquire information on obtai

32、ning these coils from the Government inventory system, contact DLA Land and Maritime ATTN: DSCC-FMTC, Post Office Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-7727. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59739A 6 7.10 Change

33、s from previous issue. The margins of this CID are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned

34、to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Custodians: Navy - EC Preparing Activity: DLA - CC DLA - CC Project 5950-20

35、13-018 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-