DLA A-A-59738-2002 INDUCTOR POWER LOW PROFILE SURFACE MOUNT《表面安装低纵面功率诱导体》.pdf

《DLA A-A-59738-2002 INDUCTOR POWER LOW PROFILE SURFACE MOUNT《表面安装低纵面功率诱导体》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59738-2002 INDUCTOR POWER LOW PROFILE SURFACE MOUNT《表面安装低纵面功率诱导体》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND A-A-59738 October 25, 2002 COMMERCIAL ITEM DESCRIPTION INDUCTOR, POWER, LOW PROFILE, SURFACE MOUNT The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers the general requirements for an induc

2、tor. Inductors covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see 7.1). AA59738 - 001 CID number Dash number (see table I) 3

3、. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Inductors supplied to this CID shall be as specified herein. (see figure 1). 3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I. 3.3 Weight. The weight shall be no greater than 0.8 gram ma

4、ximum. 3.4 Operating temperature range. The operating temperature range is 40C to +85C. 3.5 Temperature rise. DC current rating for a 30C rise. 3.6 Altitude. The maximum altitude is 70,000 feet. 3.7 Marking. Inductors supplied to this CID shall be marked with the manufacturers standard commercial PI

5、N. Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-0557, or facsimile (FAX) (61

6、4) 692-6939. AMSC N/A FSC 5950 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59738 Dimension Inches mm Dimension Inches mm A B C D E .370 Max .510 Max .330 Dia .1

7、18 Max .100 9.40 Max 12.95 Max 8.38 Dia 3.00 Max 2.54 F G H I J .300 .100 .110 .115 .290 7.62 2.54 2.79 2.92 7.37 NOTES: 1. Dimensions are in Inches. 2. Metric equivalents (in parenthesis) are listed for general information only. FIGURE 1. Configuration and dimensions. 2 Provided by IHSNot for Resal

8、eNo reproduction or networking permitted without license from IHS-,-,-A-A-59738 TABLE I. Electrical characteristics. CID dash number AA59738- L 20% (H) DCR Max (Ohms) SRF typ (MHz) Isat (A) Irms (A rms) 001 10 .11 35 2.4 2.0 002 15 .15 33 2.0 1.5 003 22 .23 25 1.6 1.3 004 33 .30 19 1.4 1.1 005 47 .3

9、9 14 1.0 .8 006 68 .66 12 .9 .7 007 100 .84 10 .7 .6 008 150 1.2 8 .6 .5 009 220 1.9 6 .5 .4 010 330 2.7 5 .4 .3 011 470 4.0 4 .3 .2 012 680 5.3 3 .2 .1 013 1000 8.4 2.5 .1 .05 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicab

10、le, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assu

11、rance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the product to be provided under this C

12、ID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b. The company must have sold 1,000 units meeting this CID in the commercial marketplace over the past 2 years. 6. PACKAGING. Preservation, packing, and marking shall b

13、e as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these

14、 inductors to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59738 7.3 Ordering data. The contract or order should specify the fol

15、lowing: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.4 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID prepa

16、ration and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs n

17、ame and address 02113 Coilcraft Inc 1102 Silver Lake Road Cary, Illinois 60013-1658 Phone number (847) 639-2361 Uniform Resource Locator (URL): 7.5 Part number (P/N) supersession data. This CID supersedes the following manufacturers P/Ns as shown. This information is being provided to assist in red

18、ucing proliferation in the government inventory system. TABLE II. P/N supersession data. CID dash number (see table I) AA59738- Vendor commercial PIN CAGE 02113 1/ 001 DO3308P-103 002 DO3308P-153003 DO3308P-223 004 DO3308P-333005 DO3308P-473 006 DO3308P-683007 DO3308P-104 008 DO3308P-154009 DO3308P-

19、224 010 DO3308P-334011 DO3308P-474 012 DO3308P-684013 DO3308P-105 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. 4 Pro

20、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59738 7.6 Government users. To acquire information on obtaining these inductors from the Government inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-CPAA, Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-7741. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Custodians: Navy - EC Preparing Activity: DLA - CC Project 5950-1153 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-