DLA A-A-59664 B-2012 CLEANING COMPOUND WINDSHIELD (SOLVENT AND ANTI-FREEZE).pdf

《DLA A-A-59664 B-2012 CLEANING COMPOUND WINDSHIELD (SOLVENT AND ANTI-FREEZE).pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59664 B-2012 CLEANING COMPOUND WINDSHIELD (SOLVENT AND ANTI-FREEZE).pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 Comments, suggestions, or questions on this document should be addressed to DLAAviation, VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616 or e-mailed to STDZNMGTdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST

2、database at https:/assist.daps.dla.mil AMSC N/A FSC 6850 INCH-POUND A-A-59664B 15 May 2012 SUPERSEDING A-A-59664A 30 August 2001 COMMERCIAL ITEM DESCRIPTION CLEANING COMPOUND, WINDSHIELD (SOLVENT AND ANTI-FREEZE) The General Services Administration has authorized the use of this commercial item desc

3、ription for all federal agencies. 1. SCOPE. This commercial item description (CID) establishes the government acquisition requirements for cleaning compound to be used in vehicle windshield washing systems. 2. CLASSIFICATION. The cleaning compound shall be classified and identified by types and size

4、s specified. The selected type and size of product to be supplied shall be specified in the acquisition order (see 7.5(b). 2.1 Type. Type I - Ready-to-use Type II - Concentrate 2.2 Size. See table I. TABLE I. Product size. Size code Size/unit of issue A 16-ounce B 1-gallon C 5-gallon D 55-gallon Pro

5、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59664B 2 3. SALIENT CHARACTERISTICS 3.1 Freezing. 3.1.1 Type I. A solution of one part cleaning compound and one-half part distilled water by volume shall be placed in a closed container, and the conta

6、iner with the solution shall be allowed to stand overnight in a freezer maintained at 0 F (-17.8 C). The solution shall remain liquid and show no evidence of freezing or formation of ice crystals. 3.1.2 Type II. A solution of one part cleaning compound and two parts distilled water by volume shall b

7、e placed in a closed container, and the container with the solution allowed to stand overnight in a freezer maintained at 0 F (-17.8 C). The solution shall remain liquid and show no evidence of freezing or formation of ice crystals. 3.2 Surface tension. 3.2.1 Type I. A solution of one part cleaning

8、compound and seven and one-half parts distilled water shall have a surface tension between 30 and 37 dynes per centimeter. 3.2.2 Type II. A solution of one part cleaning compound and sixteen parts distilled water shall have a surface tension between 30 and 37 dynes per centimeter. 3.3 Insoluble matt

9、er. Insoluble matter shall not exceed 0.005 percent by weight of a test sample of cleaning compound. 3.3.1 Test method. Filter the contents of one 16-ounce container, which has been weighed to the nearest 0.1 gram into a beaker. Then re-weigh the empty container. The ashless filter paper containing

10、the precipitate, if any, shall be washed with distilled water, then ignited, and the residue weighed to the nearest 0.0001 g (0.1 mg). The ignited residue shall be as specified in 3.3. 3.4 Deleterious action. 3.4.1 Type I. A solution of one part cleaning compound and one and one-half parts distilled

11、 water shall have no deleterious action on painted test panels. 3.4.2 Type II. A solution of one part cleaning compound and four parts distilled water shall have no deleterious action on painted test panels. 3.4.3 Test method. A solution prepared as in 3.4.1 or 3.4.2 shall be applied drop-wise to a

12、painted test panel. The drops shall be allowed to dry, and the panel rinsed with tap water and wiped with a soft cloth. There shall be no evidence of spotting, pitting, or discoloration on the painted surface. A typical test panel is a 4 X 6 inch (or larger) sheet of cold rolled 20 gauge steel on wh

13、ich has been applied one coat of primer and a subsequent coat of enamel. The painted panels should be allowed to dry at least 48 hours prior to use. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59664B 3 3.5 Workmanship. The cleaning compound s

14、hall be a colorless or tinted transparent solution, free from foreign matter and miscible with water in all concentrations. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragr

15、aph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance

16、 practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING

17、6.1 Preservation, packing, and marking. For acquisition purposes, the products shall be preserved, packed, and marked as specified in the acquisition order (see 7.5(c). 7. NOTES 7.1 Sources of documents. 7.1.1 FAR. Copies of FAR documents may be obtained from the U.S. Government Printing Office, 732

18、 North Capital Street NW, Washington, DC 20401-0001. Electronic copies of CFR documents may be obtained from http:/www.gpo.gov. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59664B 4 7.2 Part or identification number (PIN). The following PIN pr

19、ocedure is for government purposes and does not constitute a requirement for the contractor. 7.3 National stock number (NSN). The NSNs listed below are assigned for the listed product types and sizes (see table I). Other NSNs may also correspond with this document. NSN Type Size 6850-00-926-2275 II

20、A 6850-01-347-0073 I B 6850-01-368-4799 I C 6850-01-368-5489 I D 7.4 Material safety data sheets. Contracting officers will identify those activities requiring copies of the completed material safety data sheets (MSDS) prepared in accordance with FED-STD-313. The pertinent government mailing address

21、es for submission of data are listed in FED-STD-313 and 29 CFR 1910.1200 requires that the MSDS for each hazardous chemical used in an operation must identify the activities requiring copies of the MSDS. 7.5 Ordering data. Acquisition documents must specify the following information: a. CID document

22、 number, revision, and CID PIN b. Product classification type (see 2.1) and size (see 2.2) c. Preservation, packing, and marking requirements (see 6.1) 7.6 Subject term (key word) listing. concentrate washing Size: (see table I) Type: 1 - Type I - Ready-to-use 2 - Type II - Concentrate AA59664 X X C

23、ID number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59664B 5 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodian: DLA-GS GSA - FAS Preparing activity: DLA - GS3 (Project 6850-2012-005) NOTE: The activities listed above were in

24、terested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information using the ASSIST database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-