DLA A-A-59590 25 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE WITH EJECTION ACTION AND VISUAL LOCK INDICATION.pdf

《DLA A-A-59590 25 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE WITH EJECTION ACTION AND VISUAL LOCK INDICATION.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59590 25 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 225 X 260 INCH BODY SIZE WITH EJECTION ACTION AND VISUAL LOCK INDICATION.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA59590/25B 25 May 2013 SUPERSEDING AA59590/25A 20 April 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .225 X .260 INCH BODY SIZE, WITH EJECTION ACTION AND VISUAL LOCK INDICATION The General Services Administra

2、tion has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This c

3、ommercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /25 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) W, D, E Co

4、nfiguration (see table II) Example: AA59590/25EJ58 is the PIN for an electroless nickel finished, 5.8 inches (147.3 mm) long card holder with both ejection action and visual lock indication. The card holder contains two counterbore holes for rivet mounting and may be shipped unassembled to allow for

5、 rivet installation. SALIENT CHARACTERISTICS. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figures 1, 2, 3, 4, 5, and table I) and meet the general requirements of AA59590. Material. Unless otherwise specified herein,

6、the card holder materials shall be as specified in AA59590. Ejection action (see figure 2). Card holders shall have an ejection action feature that forces the circuit card assembly to disengage from its installed position. The ejection action shall allow for the initial ejection of the circuit card

7、assembly from its installed position without damaging circuits, components, or the mating connector(s). The minimal amount of ejection distance shall be .25 inch (6.4 mm). Visual lock indicator (see figure 3). Card holders shall have a visual indicator to show when the assembly is in its relaxed (un

8、locked) and expanded (locked) states. When the card holder is in the relaxed (unlocked) state, the actuating end of the screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened so that the assembly is in the expanded (locked) position, t

9、his red band shall be concealed. Performance. Card holders shall hold the circuit card assembly it is attached to firmly in its installed position and prevent loosening or movement as a result of shock and vibration. The card holder shall also provide a thermal transfer path from the circuit card as

10、sembly to the cold plate or heat sink surfaces. Actuating screw hex drive socket. The dimension for hex drive socket shall be as specified on figure 1. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/25B 2 Inches mm Inches m

11、m Inches mm Inches mm Inches mm .225 5.72 .25 .250 6.4 6.35 .270 .325 6.86 8.26 .33 .50 8.4 12.7 .61 .83 15.5 21.1 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010

12、inch (0.25 mm) for three place decimals. 3. The tolerance for the mounting hole spacing is .005 inch (0.13 mm). 4. The across flats dimension for hex drive socket shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“, and “V“. The across flats dimension for hex drive socket shall be a metr

13、ic dimension of 2.5 mm (.098 inch) across flats for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/25B 3 FIGURE 2. View of assembly installed and ejected. FIGURE 3. Visual lock

14、indicator. Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 6 inch-pounds (0.68 N-m) for assemblies using no options or option “W” and 8 inch-pounds (0.9 N-m) for assemblies using options “D“

15、or “E“. Cold plate slot width dimensions. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Finish. The finish designator shall be as specif

16、ied in AA59590. The wedge body finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting options. The mounting designators shall be as specified in AA59590. Except when using mou

17、nting option “N“, two mounting holes are required on the card holders. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ (tapped 080 UNF 2B holes), “V“ (tapped 256 UNC 2B holes), or “G“ (tapped M2.5 x.45 metric ho

18、les). See figure 1 and table I for mounting hole spacing requirements. Card holders using mounting option “J“ may be shipped unassembled. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/25B 4 Rivet mounting holes. The holes used for rivet mou

19、nting shall be .066/.073 inch (1.68/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with an access/clearance counterbore of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style A as specified in AA59590 when rive

20、t mounting is used. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the lengths available for this CID specification sheet are listed in table I. TABLE I. Assembly dim

21、ensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “M“ .005 (0.13 mm) 28 2.8 (71 mm) 1.00 (25.4 mm) 32 3.2 (81 mm) 1.40 (35.6 mm) 38 3.8 (97 mm) 2.00 (50.8 mm) 48 4.8 (122 mm) 3.00 (76.2 mm) 64 6.4 (163 mm) 4.60 (116.8 mm) 1/ Dimensions are in inches. Millimet

22、ers, in parenthesis, are given for general information only. Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. Card holders not requiring the op

23、tions described by table II shall leave the configuration position in the PIN blank. TABLE II. Configuration. Configuration designator Applicable figures Hardware options 1 and 2 No added options W 1, 2, and 3 Lockwasher and flat washer E 1, 2, and 4 Screw self-locking element D 1, 2, 3, and 4 Lockw

24、asher, flat washer and screw self-locking element Lockwasher and flat washer (see figure 4). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a lockwas

25、her and flat washer option shall include a suffix “W“ in the PIN (see table II, classification and notes section herein). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/25B 5 f FIGURE 4. Lockwasher and flat washer details. Screw self-locking

26、 element (see figure 5). The use of a screw self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw s

27、elf-locking element shall include configuration identifier “E“ in the PIN (see table II, classification and notes section herein). FIGURE 5. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-l

28、ocking element option shall include a suffix “D“ in the PIN (see table II, classification and notes section herein). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of

29、 documents. Commercial Item Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 70

30、0 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/25B 6 Ordering data. Ordering data shall be as specified in AA59590. Commercial products. As part of the market analysis and research

31、effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification she

32、et. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 732

33、8 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Elec

34、tronic mail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbe

35、rs as shown in table III. The CID PINs listed in table II are only for length designator “28“. See table IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system.

36、TABLE III. Commercial part number supersession data. PIN designator Vendor similar designator or type part number 1/ 2/ AA59590/25 CAGE 18915 CAGE 61081 CAGE 5BG68 BJ28 4550732.80B VEA2252.80H 3225VEBA2.80H BN28 4550732.80BA VEA2252.80 3225VEBA2.80 BT28 4550732.80BT VEA2252.80T0 3225VEBA2.80T0 BV28

37、4550732.80BS VEA2252.80T2 3225VEBA2.80T2 BG28 4550732.80BM MVEA2252.80TM2.5 3225VEMBA2.80TM2.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/25B 7 TABLE III. Commercial part number supersession data Continued.

38、 PIN designator Vendor similar designator or type part number 1/ 2/ AA59590/25 CAGE 18915 CAGE 61081 CAGE 5BG68 BJ28E 4550732.80BL VEA2252.80HL 3225VEBA2.80HL BN28E 4550732.80BAL VEA2252.80L 3225VEBA2.80L BT28E 4550732.80BTL VEA2252.80T0L 3225VEBA2.80T0L BV28E 4550732.80BSL VEA2252.80T2L 3225VEBA2.8

39、0T2L BG28E 4550732.80BML MVEA2252.80TM2.5L 3225VEMBA2.80TM2.5L BJ28W 4550742.80B WVEA2252.80H 3225VEWBA2.80H BN28W 4550742.80BA WVEA2252.80 3225VEWBA2.80 BT28W 4550742.80BT WVEA2252.80T0 3225VEWBA2.80T0 BV28W 4550742.80BS WVEA2252.80T2 3225VEWBA2.80T2 BG28W 4550742.80BM MWVEA2252.80TM2.5 3225VEWMBA2

40、.80TM2.5 BJ28D 4550742.80BL WVEA2252.80HL 3225VEWBA2.80HL BN28D 4550742.80BAL WVEA2252.80L 3225VEWBA2.80L BT28D 4550742.80BTL WVEA2252.80T0L 3225VEWBA2.80T0L BV28D 4550742.80BSL WVEA2252.80T2L 3225VEWBA2.80T2L BG28D 4550742.80BML MWVEA2252.80TM2.5L 3225VEWMBA2.80TM2.5L CJ28 4550732.80 VE2252.80H 322

41、5VECG2.80H CN28 4550732.80A VE2252.80 3225VECG2.80 CT28 4550732.80T VE2252.80T0 3225VECG2.80T0 CV28 4550732.80S VE2252.80T2 3225VECG2.80T2 CG28 4550732.80M MVE2252.80TM2.5 3225VEMCG2.80TM2.5 CJ28E 4550732.80L VE2252.80HL 3225VECG2.80HL CN28E 4550732.80AL VE2252.80L 3225VECG2.80L CT28E 4550732.80TL V

42、E2252.80T0L 3225VECG2.80T0L CV28E 4550732.80SL VE2252.80T2L 3225VECG2.80T2L CG28E 4550732.80ML MVE2252.80TM2.5L 3225VEMCG2.80TM2.5L CJ28W 4550742.80 WVE2252.80H 3225VEWCG2.80H CN28W 4550742.80A WVE2252.80 3225VEWCG2.80 CT28W 4550742.80T WVE2252.80T0 3225VEWCG2.80T0 CV28W 4550742.80S WVE2252.80T2 322

43、5VEWCG2.80T2 CG28W 4550742.80M MWVE2252.80TM2.5 3225VEMWCG2.80TM2.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/25B 8 TABLE III. Commercial part number supersession data Continued. PIN designator Vendor simi

44、lar designator or type part number 1/ 2/ AA59590/25 CAGE 18915 CAGE 61081 CAGE 5BG68 CJ28D 4550742.80L WVE2252.80HL 3225VEWCG2.80HL CN28D 4550742.08AL WVE2252.80L 3225VEWCG2.80L CT28D 4550742.80TL WVE2252.80T0L 3225VEWCG2.80T0L CV28D 4550742.80SL WVE2252.80T2L 3225VEWCG2.80T2L CG28D 4550742.80ML MWV

45、2252.80TM2.5L 3225VEMWCG2.80TM2.5L EJ28 4550732.80EN VEEN2252.80H 3225VEEN2.80H EN28 4550732.80ENA VEEN2252.80 3225VEEN2.80 ET28 4550732.80ENT VEEN2252.80T0 3225VEEN2.80T0 EV28 4550732.80ENS VEEN2252.80T2 3225VEEN2.80T2 EG28 4550732.80ENM MVEEN2252.80TM2.5 3225VEMEN2.80TM2.5 EJ28E 4550732.80ENL VEEN

46、2252.80HL 3225VEEN2.80HL EN28E 455073280ENAL VEEN2252.80L 3225VEEN2.80L ET28E 455073280ENTL VEEN2252.80T0L 3225VEEN2.80T0L EV28E 455073280ENSL VEEN2252.80T2L 3225VEEN2.80T2L EG28E 455073280ENML MVEEN2252.80TM2.5L 3225VEMEN2.80TM2.5L EJ28W 4550742.80EN WVEEN2252.80H 3225VEWEN2.80H EN28W 4550742.80ENA

47、 WVEEN2252.80 3225VEWEN2.80 ET28W 4550742.80ENT WVEEN2252.80T0 3225VEWEN2.80T0 EV28W 4550742.80ENS WVEEN2252.80T2 3225VEWEN2.80T2 EG28W 4550742.80ENM MWVEEN2252.80TM2.5 3225VEWMEN2.80TM2.5 EJ28D 4550742.80ENL WVEEN2252.80HL 3225VEWEN2.80HL EN28D 455074280ENAL WVEEN2252.80L 3225VEWEN2.80L ET28D 455074280ENTL WVEEN2252.80T0L 3225VEWEN2.80T0L EV28D 455074280ENSL WVEEN2252.80T2L 3225VEWEN2.80T2L EG28D 455074280ENML MWVEEN2252.80TM2.5L 3225VEWMEN2.80TM2.5L H