DLA A-A-59590 24 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 500 X 450 INCH BODY SIZE WITH VISUAL LOCK INDICATION AND SCREW RETENTION.pdf

《DLA A-A-59590 24 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 500 X 450 INCH BODY SIZE WITH VISUAL LOCK INDICATION AND SCREW RETENTION.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59590 24 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 500 X 450 INCH BODY SIZE WITH VISUAL LOCK INDICATION AND SCREW RETENTION.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA59590/24B 24 March 2013 SUPERSEDING AA59590/24A 17 October 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE .500 X .450 INCH BODY SIZE, WITH VISUAL LOCK INDICATION AND SCREW RETENTION The General Services Adminis

2、tration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). Thi

3、s commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /24 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) * Confi

4、guration (see table II) Example: AA59590/24ET48E is the PIN for a nickel plated, 4.8 inches (122 mm) long card holder with a visual lock indication and a screw self-locking element. The card holder also features two tapped 0-80 UNF mounting holes for use with fasteners. SALIENT CHARACTERISTICS. Inte

5、rface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figures 1, 2, 3, 4, and table I) and meet the general requirements of CID AA59590. Material. Unless otherwise specified herein, the card holder materials shall be as specified i

6、n AA59590. Performance. Card holders shall hold the circuit card assembly it is attached to firmly in its installed position and prevent loosening or movement as a result of shock and vibration. The card holder shall also provide a thermal transfer path from the circuit card assembly to the cold pla

7、te or heat sink surfaces. Actuating screw hex drive socket. The dimension for hex drive socket shall be as specified on figure 1. Screw retention (see figure 2). The screw retention feature is intended to prevent the unintentional disassembly of the card holder. The self-locking nut used for the scr

8、ew retention feature shall be fabricated of a corrosion resistant material. Visual lock indicator (see figure 3). Card holders shall have a visual indicator to show when the card holder assembly is in its relaxed (unlocked) state. When the card holder assembly is in the relaxed state, the end of the

9、 actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened so that the assembly is in the expanded (locked) position, this red band shall be concealed. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking

10、permitted without license from IHS-,-,-AA59590/24B 2 Inches mm Inches mm Inches mm Inches mm Inches mm .156 .25 3.96 6.4 .27 .30 6.9 7.6 .40 .460 10.2 11.68 .500 .57 12.7 14.5 .600 .70 15.24 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherw

11、ise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The tolerance for the mounting hole spacing is .005 inches (0.13 mm). 4. The across flats dimension for hex drive socket shall be .156 inch (3.96 mm) for mounting options “J“,

12、 “N“, “T“, and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 3.0 mm (.118 inch) across flats for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions, basic configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

13、ense from IHS-,-,-AA59590/24B 3 FIGURE 2. Screw retaining self-locking nut details. FIGURE 3. Visual lock indicator details. Cold plate dimensions. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .525 inch (13.3 mm) plus the thickness of the

14、printed board of the circuit card assembly (see AA59590). Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 31 inch-pounds (3.5 N-m) for assemblies using no options or option “W“ and 34 to 36 i

15、nch-pounds (3.8 to 4.1 N-m) for assemblies using options “D“ or “E“. Finish. The finish materials shall be as specified in AA59590. The wedge body finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard bl

16、ack anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. Except when using mounting option “N”, two mounting holes are required on the card holders. The mounting options available for this CID specification sheet are as follows: “J“ (rivet moun

17、ting holes), “N“ (no mounting holes), “T“ (tapped 0-80 UNF 2B holes), “V“ (tapped 2-56 UNC 2B holes), or “G“ (tapped M2.5 x.45 metric holes). See figure 1 and table I for mounting hole spacing requirements. Card holders using mounting option “J” may be shipped unassembled. Rivet mounting holes. The

18、holes used for rivet mounting shall be .136 inch (3.45 mm) diameter, countersunk 100 degrees by .190/.200 inch (4.83/5.08 mm) diameter through holes with an access/clearance counterbore of .190/.200 inch (4.83/5.08 mm) diameter by .390 inch (9.91 mm) deep. Rivets. This card holder uses rivet style B

19、 as specified in AA59590 when rivet mounting is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/24B 4 Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59590 and the lengths available for this CI

20、D specification sheet are listed in table I. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE I. Assembly dimensions (see figure 1). PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “B“ .03 (0.8 mm) Dimension “M“ .005 (0.13 mm) 28 2.8 (71 mm) 2.30

21、(58.4 mm) .90 (22.9 mm) 38 3.8 (97 mm) 3.30 (83.8 mm) 1.90 (48.3 mm) 48 4.8 (122 mm) 4.30 (109.2 mm) 2.90 (73.7 mm) 58 5.8 (147 mm) 5.30 (134.6 mm) 3.90 (99.1 mm) Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of

22、 those on figures 1, 2 and 3, and may include those on figures 4 and 5. The correct PIN configuration identifier for each option is listed in table II. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configuration. Confi

23、guration designator Applicable figures Hardware added to basic configuration 1, 2 and 3 No changes from basic configuration W 1, 2, 3 and 4 Lockwasher and flat washer E 1, 2, 3 and 5 Screw self-locking element D 1, 2, 3, 4 and 5 Lockwasher, flat washer, and screw self-locking element Lockwasher and

24、flat washer (see figure 4). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a lockwasher and flat washer option shall include a suffix “W“ in the PIN

25、(see classification and notes herein). FIGURE 4. Lockwasher and flat washer details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/24B 5 Screw self-locking element (see figure 5). The use of a self-locking element on the screw will provide

26、a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw self-locking element shall include configuration identifier “E“ in the PIN (see classificati

27、on and notes herein). FIGURE 5. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a suffix “D“ in the PIN (see classification and notes herein). NOTES. PIN

28、. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description. AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, Gener

29、al Requirements For. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA59

30、590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial p

31、roducts that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted wit

32、hout license from IHS-,-,-AA59590/24B 6 Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Elect

33、ronic mail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part number

34、s as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system.

35、TABLE III. Commercial part number supersession data. PIN designator AA59590/24 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 BJ28 VA255CR2.80HR 3500VBA2.80HR BN28 VA255CR2.80R 3500VBA2.80R BT28 VA255CR2.80T0R 3500VBA2.80T0R BV28 VA255CR2.80T2R 3500VBA2.80T2R BG28 MVA255CR

36、2.80TM2.5R 3500MVBA2.80TM2.5R BJ28W WVA255CR2.80HR 3500VWBA2.80HR BN28W WVA255CR2.80R 3500VWBA2.80R BT28W WVA255CR2.80T0R 3500VWBA2.80T0R BV28W WVA255CR2.80T2R 3500VWBA2.80T2R BG28W MWVA255CR2.80TM2.5R 3500MVWBA2.80TM2.5R BJ28E VA255CR2.80HLR 3500VBA2.80HLR BN28E VA255CR2.80LR 3500VBA2.80LR BT28E VA

37、255CR2.80T0LR 3500VBA2.80T0LR BV28E VA255CR2.80T2LR 3500VBA2.80T2LR BG28E MVA255CR2.80TM2.5LR 3500MVBA2.80TM2.5LR BJ28D WVA255CR2.80HLR 3500VWBA2.80HLR BN28D WVA255CR2.80LR 3500VWBA2.80LR BT28D WVA255CR2.80T0LR 3500VWBA2.80T0LR BV28D WVA255CR2.80T2LR 3500VWBA2.80T2LR BG28D MWVA255CR2.80TM2.5LR 3500M

38、VWBA2.80TM2.5LR See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/24B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/24 Vendor similar designator or type part number 1/ 2/

39、CAGE 61081 CAGE 5BG68 CJ28 V255CR2.80HR 3500VCG2.80HR CN28 V255CR2.80R 3500VCG2.80R CT28 V255CR2.80T0R 3500VCG2.80T0R CV28 V255CR2.80T2R 3500VCG2.80T2R CG28 MV255CR2.80TM2.5R 3500MVCG2.80TM2.5R CJ28W WV255CR2.80HR 3500VWCG2.80HR CN28W WV255CR2.80R 3500VWCG2.80R CT28W WV255CR2.80T0R 3500VWCG2.80T0R C

40、V28W WV255CR2.80T2R 3500VWCG2.80T2R CG28W MWV255CR2.80TM2.5R 3500MVWCG2.80TM2.5R CJ28E V255CR2.80HLR 3500VCG2.80HLR CN28E V255CR2.80LR 3500VCG2.80LR CT28E V255CR2.80T0LR 3500VCG2.80T0LR CV28E V255CR2.80T2LR 3500VCG2.80T2LR CG28E MV255CR2.80TM2.5LR 3500MVCG2.80TM2.5LR CJ28D WV255CR2.80HLR 3500VWCG2.8

41、0HLR CN28D WV255CR2.80LR 3500VWCG2.80LR CT28D WV255CR2.80T0LR 3500VWCG2.80T0LR CV28D WV255CR2.80T2LR 3500VWCG2.80T2LR CG28D MWV255CR2.80TM2.5LR 3500MVWCG2.80TM2.5LR EJ28 VEN255CR2.80HR 3500VEN2.80HR EN28 VEN255CR2.80R 3500VEN2.80R ET28 VEN255CR2.80T0R 3500VEN2.80T0R EV28 VEN255CR2.80T2R 3500VEN2.80T

42、2R EG28 MVEN255CR2.80TM2.5LR 3500MVEN2.80TM2.5R EJ28W WVEN255CR2.80HR 3500VWEN2.80HR EN28W WVEN255CR2.80R 3500VWEN2.80R ET28W WVEN255CR2.80T0R 3500VWEN2.80T0R EV28W WVEN255CR2.80T2R 3500VWEN2.80T2R EG28W MWVEN255CR2.80TM2.5R 3500MVWEN2.80TM2.5R See footnotes at end of table. Provided by IHSNot for R

43、esaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/24B 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/24 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 EJ28E VEN255CR2.80HLR 3500VEN2.80HLR EN28E VEN255

44、CR2.80LR 3500VEN2.80LR ET28E VEN255CR2.80T0LR 3500VEN2.80T0LR EV28E VEN255CR2.80T2LR 3500VEN2.80T2LR EG28E MVEN255CR2.80TM2.5LR 3500MVEN2.80TM2.5LR EJ28D WVEN255CR2.80HLR 3500VWEN2.80HLR EN28D WVEN255CR2.80LR 3500VWEN2.80LR ET28D WVEN255CR2.80T0LR 3500VWEN2.80T0LR EV28D WVEN255CR2.80T2LR 3500VWEN2.8

45、0T2LR EG28D MWVEN255CR2.80TM2.5LR 3500MVWEN2.80TM2.5LR HJ28 VHA255CR2.80HR 3500VBH2.80HR HN28 VHA255CR2.80R 3500VBH2.80R HT28 VHA255CR2.80T0R 3500VBH2.80T0R HV28 VHA255CR2.80T2R 3500VBH2.80T2R HG28 MVHA255CR2.80TM2.5LR 3500MVBH2.80TM2.5R HJ28W WVHA255CR2.80HR 3500VWBH2.80HR HN28W WVHA255CR2.80R 3500

46、VWBH2.80R HT28W WVHA255CR2.80T0R 3500VWBH2.80T0R HV28W WVHA255CR2.80T2R 3500VWBH2.80T2R HG28W MWVHA255CR2.80TM2.5LR 3500MVWBH2.80TM2.5R HJ28E VHA255CR2.80HLR 3500VBH2.80HLR HN28E VHA255CR2.80LR 3500VBH2.80LR HT28E VHA255CR2.80T0LR 3500VBH2.80T0LR HV28E VHA255CR2.80T2LR 3500VBH2.80T2LR HG28E VMHA255C

47、R2.80TM2.5LR 3500MVBH2.80TM2.5R HJ28D WVHA255CR2.80HLR 3500VWBH2.80HLR HN28D WVHA255CR2.80LR 3500VWBH2.80LR HT28D WVHA255CR2.80T0LR 3500VWBH2.80T0LR HV28D WVHA255CR2.80T2LR 3500VWBH2.80T2LR HG28D MWVHA255CR2.80TM2.5LR 3500MVWBH2.80TM2.5LR See footnotes at end of table. Provided by IHSNot for ResaleN

48、o reproduction or networking permitted without license from IHS-,-,-AA59590/24B 9 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/24 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 RJ28 VR255CR2.80HR 3500VCC2.80HR RN28 VR255CR2.80R 3500VCC2.80R RT28 VR255CR2.80T0R 3500VCC2.80T0R RV28 VR2