DLA A-A-59585 C-2008 BEARING BALL ANNULAR SINGLE ROW RADIAL NON-FILLING SLOT DIMENSION SERIES 03《03尺寸系列无装球缺口的辐射状单排环形滚珠轴承》.pdf

《DLA A-A-59585 C-2008 BEARING BALL ANNULAR SINGLE ROW RADIAL NON-FILLING SLOT DIMENSION SERIES 03《03尺寸系列无装球缺口的辐射状单排环形滚珠轴承》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59585 C-2008 BEARING BALL ANNULAR SINGLE ROW RADIAL NON-FILLING SLOT DIMENSION SERIES 03《03尺寸系列无装球缺口的辐射状单排环形滚珠轴承》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 METRIC A-A-59585C 15 September 2008 SUPERSEDING A-A-59585B 23 September 2003 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 03 The General Servic

2、es Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers metric, single row, radial, non-filling slot, annular ball bearings for general-purpose use. These bearings are not intended for use in criti

3、cal aeronautical or critical special precision applications. 2. CLASSIFICATION. The ball bearings shall be classified by the class, sizes, cage materials, shield and seal configurations, precision tolerances, and lubricant and preservative requirements listed below: Class 2 - dimension series 03 Siz

4、es - bearing dimensions (see Table I) Cage materials (see Table II) Shield and seal configurations (see Table III) Precision tolerances (see Table IV) Lubricant and preservative requirements (see Table V) 3. SALIENT CHARACTERISTICS 3.1 Dimensions. Bearing boundary dimensions shall conform to the req

5、uirements specified in Table I for each of the coded bearing sizes. The listed dimensions conform to the requirements specified for the listed bearing sizes from dimension series 03 in American Bearing Manufacturers Association (ABMA) Standard 20, “Radial Bearings of Ball, Cylindrical Roller, and Sp

6、herical Roller Types, Metric Design“. The bearing size shall be as specified in the acquisition order (see that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. AMSC N/A FSC 3

7、110 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59585C 2 7.3(b). For unlisted bearing sizes, the associated dimensional and dynamic load rating requirements should also be specified in the acquisition order. Table I. Dimensional requirements

8、(ABMA series 03). Bearing size code Bore diameter (mm) Outside diameter (mm) Width(mm) Chamfer r/min. (mm) Minimum shaft shoulder diameter1(mm) Dynamic load rating (minimum) (lb.) 00 10 35 11 0.6 15 1,81001 12 37 12 1.0 18 2,12002 15 42 13 1.0 21 2,55003 17 47 14 1.0 23 3,04004 20 52 15 1.1 27 3,570

9、05 25 62 17 1.1 32 4,63106 30 72 19 1.1 37 6,00007 35 80 21 1.5 43.5 7,46008 40 90 23 1.5 48.5 9,10509 45 100 25 1.5 53.5 10,99310 50 110 27 2.0 60 13,90011 55 120 29 2.0 65 16,07412 60 130 31 2.1 72 18,30013 65 140 33 2.1 77 20,79514 70 150 35 2.1 82 23,38015 75 160 37 2.1 87 25,40316 80 170 39 2.1

10、 92 27,50017 85 180 41 3.0 99 28,50018 90 190 43 3.0 104 30,00019 95 200 45 3.0 109 32,50020 100 215 47 3.0 114 36,50021 105 225 49 3.0 119 39,00022 110 240 50 3.0 124 42,50024 120 260 55 3.0 134 46,50026 130 280 58 4.0 148 51,05028 140 300 62 4.0 158 56,40030 150 320 65 4.0 168 61,50032 160 340 68

11、4.0 178 62,10034 170 360 72 4.0 188 70,10036 180 380 75 4.0 198 78,90038 190 400 78 5.0 212 79,5001Listed for reference purposes only. Shoulder height shall be determined to provide sufficient clearance for the direct application of bearing removal force against the bearing inner ring. If the requir

12、ed minimum clearance is not available, an alternative non-destructive bearing removal capability shall be provided. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59585C 3 3.2 Materials. 3.2.1 Rings. The bearing ring material shall be chromium-a

13、lloy steel 52100 (UNS G52986) as specified in ASTM International (ASTM) A 295/A 295M, “Standard Specification for High-Carbon Anti-Friction Bearing Steel“. The finished rings shall not exceed the associated billet material inclusion rating, which is also specified in ASTM A 295/A 295M. Ring hardness

14、 shall be no less than 58 HRC as defined in ASTM E 18, “Standard Test Methods for Rockwell Hardness of Metallic Materials“. The grain size of the ring material shall be determined in accordance with ASTM E 112, “Standard Methods for Determining Average Grain Size“. 3.2.2 Balls. The bearing ball mate

15、rial shall be chromium-alloy steel 52100 (UNS G52986) as specified in ASTM A 295/A 295M. The finished balls shall not exceed the associated billet material inclusion rating, which is also specified in ASTM A 295/A 295M. Balls shall be through-hardened no less than 60 HRC and no more than 67 HRC as d

16、efined in ASTM E 18. The grain size of the ball material shall be determined in accordance with ASTM E 112. 3.2.3 Cage. The bearing cage material shall be impervious to deterioration from any lubricant, preservative, solvent, or other chemical substance expected to contact the bearing during normal

17、use or storage. Similarly, the material shall not cause any chemical deterioration of any other bearing component. . Metallic cage materials shall operate from -40 F to 250 F (-40 C to 121 C). Non-metallic cage materials shall operate from -20 F to 250 F (-30 C to 121 C). Unless otherwise specified

18、in the acquisition order, the cage material shall be one of the optional coded types listed in Table II (see 7.3(c). Table II. Cage materials. Code1Material type J Pressed steel M Machined bronze or brass P Molded plastic (nylon 6/6 or equal) T Machined non-metallic (phenolic) Y Pressed brass 1No si

19、gnificant changes from FF-B-171/5. 3.2.4 Shields and seals. When used, the shield or seal material shall be as recommended by the manufacturer, unless otherwise specified in the acquisition order (see 7.3(d). The material shall be impervious to deterioration from any lubricant, preservative, solvent

20、, or other chemical substance expected to contact the bearing during normal use or storage. Similarly, the material shall not cause any chemical deterioration of any other bearing component. The shield or seal shall remain functionally effective at a minimum temperature range of -20 F to 250 F (-30

21、C to 121 C) for non-metallic, and -40 F to 250 F (-40 C to 121 C) for metallic materials. Unless otherwise specified in the acquisition order, the shield and seal configuration for the bearing shall be one of the coded options listed in Table III (see 7.3(e). Provided by IHSNot for ResaleNo reproduc

22、tion or networking permitted without license from IHS-,-,-A-A-59585C 4 Table III. Shield and seal configurations. Code1Configuration option A Open B Single shield C Double shield D Single seal E Double seal G Open with snap ring H Single shield on snap ring side J Single shield opposite snap ring K

23、Double shield with snap ring X Other (specify in acquisition order) 1No significant changes from FF-B-171/5. 3.2.5 Snap ring. When used, the bearing snap ring and associated snap ring groove shall conform to the requirements specified in ABMA Standard 20. 3.3 Precision tolerance. The bearing precisi

24、on tolerance level shall conform to Annular Bearing Engineers Committee (ABEC) class ABEC-1, ABEC-3, ABEC-5, or ABEC-7 as defined in ABMA Standard 20. The tolerance class and associated radial internal clearance shall be one of the coded options listed in Table IV (see 7.3(f). 3.3.1 Bearing precisio

25、n tolerance levels and internal clearances may be affected by the addition of shields and/or seals. Manufacturers/suppliers should be consulted for availability of desired precision tolerances when shields and/or seals are required. 3.4 Lubrication and preservation requirements. Unless otherwise spe

26、cified in the acquisition order, the bearing lubricant or preservative requirement shall be as selected from the approved coded options listed in Table V (see 7.3(g). When grease fill is required, the bearing void (the airspace between the inner and outer rings of the assembled bearing) shall be 25

27、to 50 percent filled. Bearing preservative shall be in accordance with MIL-DTL-197, “Packaging of Bearings, Associated Parts and Subassemblies“. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in a

28、ccordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Unless otherwise indicated in the solicitation and resulting contract, the foreign acquisition restrictions in Section 252.225, Clause 252.225.7016 of the Defense Federal Acquisition Regulation Supplement (DFARS) apply

29、to products described by this CID. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59585C 5 Table IV. Precision tolerance requirements. Code Tolerance class Radial internal clearance A Group 2 (less than normal) B Group N (normal) C Group 3 (grea

30、ter than normal) D Group 4 (greater than group 3) T ABEC-1 Group 5 (greater than group 4) E Group 2 (less than normal) F Group N (normal) G Group 3 (greater than normal) H Group 4 (greater than group 3) U ABEC-3 Group 5 (greater than group 4) J Group 2 (less than normal) K Group N (normal) L Group 3

31、 (greater than normal) M Group 4 (greater than group 3) V ABEC-5 Group 5 (greater than group 4) N Group 2 (less than normal) P Group N (normal) R Group 3 (greater than normal) S Group 4 (greater than group 3) W ABEC-7 Group 5 (greater than group 4) Table V. Lubricant and preservative requirements. C

32、ode Lubricant or preservative compound B Grease in accordance with MIL-PRF-81322 E Grease in accordance with DOD-G-24508 H Grease in accordance with MIL-PRF-23827 L Grease with SRI-2 or qualified equivalent P Grease in accordance with A-A-59685 S No fill T Preservation compound in accordance with MI

33、L-DTL-197 X Other (specify in the acquisition order) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59585C 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial

34、 item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product

35、offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Unless otherwise specified in the acquisition order, the bearings supplied shall be preserved, packed, and marked in accordance with MIL-DTL-197 (see 7.3(

36、h). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. AA59585 - 2 34 J A B E Example of reference part number: Lubricant and preservative code (see Table V) Precision tolerance code (see

37、Table IV) Shield and seal code (see Table III) Cage material code (see Table II) Bearing size code (see Table I) Class 2 - dimension series 03 CID number AA59585 - 2 34 J A B E indicates: boundary dimension series 03; bore diameter 170 mm, outside diameter 360 mm, width 72 mm; pressed steel cage; op

38、en; ABEC-1 tolerance class, normal radial internal clearance; filled with grease in accordance with DOD-G-24508. 7.2 Sources of documents. 7.2.1 ABMA standards. Copies of ABMA standards may be obtained from the American Bearing Manufacturers Association, 2025 M Street NW, Suite 800, Washington, DC 2

39、0036. Electronic copies of ABMA standards may be obtained from http:/www.abma-dc.org/. 7.2.2 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standards may be obtained f

40、rom http:/www.astm.org/. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59585C 7 7.2.3 FAR and DFARS. Copies of the FAR and DFARS may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copi

41、es of the FAR may be obtained from http:/www.arnet.gov/far/. Electronic copies of the DFARS may be obtained from http:/www.acq.osd.mil/dp/dars/dfars.html. 7.2.4 Military specifications and standards. Copies of military specifications and standards may be obtained from Standardization Documents Order

42、 Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. Electronic copies of military specifications and standards may be obtained from http:/assist.daps.dla.mil/quicksearch/. 7.3 Ordering data. Acquisition documents should specify the following information: a. CID document number, revi

43、sion, and CID PIN. b. Bearing size (with dimension/load requirements if size is unlisted) (see 3.1). c. Cage material type (see 3.2.3). d. Shield and seal material (see 3.2.4). e. Shield and seal configuration (see 3.2.4). f. Precision tolerance requirement (see 3.3). g. Lubricant and preservative r

44、equirement (see 3.4). h. Preservation, packaging, and marking requirements (see 6.1). 7.4 Codes cross-reference. Tables VI, VII, and VIII contain cross-reference data for the PIN information as listed in FF-B-171/5 and this CID. 7.4.1 Bearing class designations. The CIDs replacing 33 of the 37 assoc

45、iated specification sheets of FF-B-171 have been assigned class codes corresponding to ABMA dimension series. Table VI lists the FF-B-171 specification sheets, the corresponding dimension series, the CID class codes, and the replacement CIDs. Provided by IHSNot for ResaleNo reproduction or networkin

46、g permitted without license from IHS-,-,-A-A-59585C 8 Table VI. Federal specification to CID cross-reference. FF-B-171 specification sheets ABMA dimension series CID class codes Replacement CID numbers 1 02, 03, 10 1, 2, 4 A-A-59581 2 19 5 A-A-59582 3 10 4 A-A-59583 4 02 1 A-A-59584 5 03 2 A-A-59585

47、 6 04 3 A-A-59586 7 02 1 A-A-59587 8 03 2 A-A-59589 9 32 8 A-A-59595 10 33 9 A-A-59596 11 02 1 A-A-59597 12 03 2 A-A-59598 13 22 6 A-A-59599 14 23 7 A-A-59600 15 19 - Canceled 16 10 - Canceled 17 02 - Canceled 18 03 - Canceled 19 19 5 A-A-59623 20 10 4 A-A-59624 21 02 1 A-A-59625 22 03 2 A-A-59626 2

48、3 04 3 A-A-59627 24 10 4 A-A-59628 25 02 1 A-A-59629 26 03 2 A-A-59630 27 04 3 A-A-59631 28 10 4 A-A-59632 29 02 1 A-A-59633 30 03 2 A-A-59634 31 04 3 A-A-59635 32 32 8 A-A-59636 33 33 9 A-A-59637 34 32 8 A-A-59638 35 33 9 A-A-59639 36 32 8 A-A-59640 37 33 9 A-A-59641 Provided by IHSNot for ResaleNo

49、 reproduction or networking permitted without license from IHS-,-,-A-A-59585C 9 Table VII. Radial internal clearance and ABEC tolerance codes. FF-B-171/5 codes A-A-59585 codes Code Radial internal clearance Tolerance class Code Tolerance class Radial internal clearance 1 Symbol 2 A Group 2 2 Symbol 0 B Group N 3 Symbol