DLA A-A-59497 A-2010 RESISTORS VARIABLE NONWIRE WOUND WIRE WOUND PRECISION NONPRECISION GENERAL REQIUIREMENTS FOR.pdf

《DLA A-A-59497 A-2010 RESISTORS VARIABLE NONWIRE WOUND WIRE WOUND PRECISION NONPRECISION GENERAL REQIUIREMENTS FOR.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59497 A-2010 RESISTORS VARIABLE NONWIRE WOUND WIRE WOUND PRECISION NONPRECISION GENERAL REQIUIREMENTS FOR.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND A-A-59497A 17 June 2010 SUPERSEDING A-A-59497 23 February 2000 COMMERICAL ITEM DESCRIPTION RESISTORS, VARIABLE, NONWIRE WOUND, WIRE WOUND, PRECISION, NONPRECISION, GENERAL REQIUIREMENTS FOR The General Services Administration has authorized the use of this Commercial Item Description (CI

2、D) for all federal agencies. 1. SCOPE. This CID covers the general requirements for wire wound, nonwire wound, precision, nonprecision variable resistors. The individual requirements for specific resistors are covered in the individual CID sheets. For technical assistance when utilizing parts for pa

3、rameters not specifically detailed, contact the manufacturers listed on applicable CID sheets. The resistors covered by this CID are intended for commercial/industrial applications. * 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system which is included in th

4、e PIN as shown in the following example (see 7.1) A59497 01 * * * * * Abbreviated CID number Applicable CID sheet (two digits) Resistance (see 3.2) Resistance tolerance (see 3.3) Physical parameters (see 3.4) Operating shaft (see 3.5) Electrical rotation and linearity (see 3.6) 3. SALIENT CHARTACTER

5、ISTICS 3.1 Interface and physical dimensions. The resistors supplied to this CID shall be as specified on the applicable CID sheet. 3.2 Resistance. The nominal resistance value expressed in ohms is identified by a three-digit number; the first two digits represent significant figures and the last di

6、git specifies the number of zeros to follow. Resistance values for specific resistors are covered in the individual CID sheets. 3.3 Resistance tolerance. The resistance tolerance shall be as specified on the applicable CID sheet. Comments, suggestions, or questions on this document should be address

7、ed to Defense Supply Center Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, or emailed to Resistordla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AM

8、SC N/A FSC 5905 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59497A 2 3.4 Physical parameters. The physical parameters shall be as specified on the applicable CID sheet. 3.5 Operating shaft. The operating shaft style and length shall be as spe

9、cified on the applicable CID sheet. 3.6 Electrical rotation and linearity. The electrical rotation and linearity shall be as specified on the applicable CID sheet 3.7 Power rating. The power rating shall be as specified on the applicable CID sheet. 3.8 Operating ambient temperature. The operating am

10、bient temperature shall be as specified on the applicable CID sheet. 3.9 Marking. Resistors supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. * 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally prefera

11、ble materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. * 3.11 Workmanship. Resistor shall be processed in such a manner as to be uniform in quality

12、and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT

13、CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and is the same product offered for sale in the commercial market. The Governm

14、ent reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example.

15、 * 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority

16、 chemicals. The list of chemicals and additional information is available on their website at http:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed t

17、o meet the requirements specified herein (see Section 3).” Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59497A 3 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these resistors to D

18、SCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE Code 58536 should be used. * 7.4 Source of documents. FEDERAL REGULATIONS FAR 23.403 - Federal Acquisition Regulations (FAR) Use of Recovered Materials. (Copies of these documents are available online at www.acquisi

19、tion.gov/comp/far/index.html or from the U. S. Government Printing Office, 732 North Capital Street, NW Washington D.C. 20401.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requir

20、ements. 7.6 Government users. To acquire information on obtaining these resistors from the Government inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-CPB, Post Office Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-7678. * 7.7 Changes from previous issue. The margins

21、of this CID are marked with an asterisk to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of t

22、his document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodian GSA - 7FXE NAVY - EC Preparing Activity: DLA - CC DLA - CC Project 5905-2010-014 NOTE: The activities listed

23、above were interested in this document as the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-