DLA A-A-59494 1-2010 WHEELS AND HUB ASSEMBLIES.pdf

《DLA A-A-59494 1-2010 WHEELS AND HUB ASSEMBLIES.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59494 1-2010 WHEELS AND HUB ASSEMBLIES.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND A-A-59494/1 28 April 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET WHEELS AND HUB ASSEMBLIES The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring wheels and hubs described he

2、rein shall consist of this document and the issue in effect of A-A-59494. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES). AA59494 /0

3、1 - 001 CID number Applicable Dash number CID specification (see figure 1) sheet (two digits) SALIENT CHARACTERISTICS. Interface and physical dimensions. Wheel and hub assemblies supplied to this CID specification sheet shall be as specified herein (see figure 1). FORK (REF)WHEELHUBHUBWHEELType I, c

4、antilever mounting Type II, fork mounting FIGURE 1. Wheel and hub assembly types. AMSC N/A FSC 2530 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59494/1 2 Dash number Size Wheel Hub Mounting 001 3.50-6 A-A-59494/2 A-A-59494/6 Cantilever 002 3.

5、50-6 A-A-59494/2 A-A-59494/8 Fork 003 4.00-8 A-A-59494/3 A-A-59494/6 Cantilever 004 4.00-8 A-A-59494/3 A-A-59494/8 Fork 005 6.00-9 A-A-59494/4 A-A-59494/7 Cantilever 006 6.00-9 A-A-59494/4 A-A-59494/9 Fork 007 7.50-10 A-A-59494/5 A-A-59494/7 Cantilever 008 7.50-10 A-A-59494/5 A-A-59494/9 Fork 009 9.

6、00-10 A-A-59494/5 A-A-59494/7 Cantilever NOTE: This shall be a demountable type wheel which can be removed from the hub without deflating the tire. FIGURE 1. Wheel and hub assembly types Continued. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID spec

7、ification sheet. See the classification section for PIN format example. Source of documents. COMMERCIAL ITEM DESCRIPTIONS A-A-59494 - Wheels and Hubs for Industrial Pneumatic Tires (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ from the Standardization Doc

8、ument Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet prepa

9、ration and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers show

10、n.) MFRs CAGE MFRs name and address 52793 Saginaw Products Corporation 68 Williamson St. Saginaw, MI 48601-3246 Phone: 989-753-1411 Fax: 989-753-4386 http:/ 56190 Metadure Parts & Sales Inc. 165 Gazza Blvd. Farmingdale, NY 11735 Phone: 631-249-2141 Fax: 631-249-4546 Provided by IHSNot for ResaleNo

11、 reproduction or networking permitted without license from IHS-,-,-A-A-59494/1 3 OW357 PDI Ground Support Systems Inc. 5905 Grant Ave. Cleveland, OH 44515-5609 Phone: 216-271-7344 Fax: 216-271-7550 davidrpdi- http:/www.pdi- Part number (P/N) supersession data. These CID specification sheet PINs supe

12、rsede the following MFRs P/Ns as shown (see table I). This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE I. P/N supersession data. Dash number (see figure 1) A-A-59494/1 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ 00

13、1 52793 6416-M 56190 N/A OW357 N/A 002 52793 6426-M 56190 N/A OW357 N/A 003 52793 6418-M 56190 N/A OW357 N/A 004 52793 6428-M 56190 N/A OW357 N/A 005 52793 6419-M 56190 N/A OW357 N/A 006 52793 6429-M 56190 N/A OW357 N/A 007 52793 6420-AL 56190 N/A OW357 N/A 008 52793 6430-M 56190 N/A OW357 N/A 009 5

14、2793 6420-M 56190 N/A OW357 N/A 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown.

15、 For actual part marking requirements, see the marking paragraph of A-A-59494. National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID specification sheet. The list is for information only and may not be indicative of all possible NSNs associated with the C

16、ID specification sheet. For up to date information on assigned NSNs, please contact the aforementioned DSCC office listed in A-A-59494 (see table II). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59494/1 4 TABLE II. NSNs. Dash number (see figu

17、re1) A-A-59494/1 NSN 001 2530-00-063-1358 002 N/A 003 2530-00-063-1359 004 N/A 005 2530-00-063-1361 006 N/A 007 2530-01-295-7168 008 N/A 009 2530-00-063-1364 MILITARY INTERESTS: CIVIL AGENCY AND COORDINATING ACTIVITY: Custodians: GSA - FAS Army - AT Air Force - 99 Preparing activity: DLA CC DLA - CC

18、 Review activity: Project 2530-2009-001 Air Force - 84 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-