DLA A-A-59430-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL CLOSED-END DOMED HEAD ALUMINUM ALLOY《铝合金制球形圆柱式封闭端型限动芯棒用非结构性盲铆钉》.pdf

《DLA A-A-59430-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL CLOSED-END DOMED HEAD ALUMINUM ALLOY《铝合金制球形圆柱式封闭端型限动芯棒用非结构性盲铆钉》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59430-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL CLOSED-END DOMED HEAD ALUMINUM ALLOY《铝合金制球形圆柱式封闭端型限动芯棒用非结构性盲铆钉》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 5 FSC 5320DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-5943020 April 1999COMMERCIAL ITEM DESCRIPTIONRIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL,CLOSED-END, DOMED HEAD, ALUMINUM ALLOYThis General Services Administration has authorized

2、 the use of this Commercial Item Description forall Federal agencies.1. SCOPE: This Commercial Item Description (CID) covers the requirements for pull-stem expandable blindrivets. These rivets are intended for rapid and permanent non-structural fastening applications in which accessis available to o

3、ne side only.2. SALIENT CHARACTERISTICS:2.1 Blind rivets furnished under this CID shall conform to the materials, strengths, and dimensions as specified inTable I, II, and III and as shown in Figure 1 below.FIGURE 1. RIVETSBENEFICIAL COMMENTS, RECOMMENDATIONS, ADDITIONS, DELETIONS, CLARIFICATIONS,ET

4、C., AND DATA WHICH MAY IMPROVE THIS DOCUMENT SHOULD BE SENT TO: DEFENSEINDUSTRIAL SUPPLY CENTER, ATTN: DISC-AEEB, 700 ROBBINS AVENUE, PHILADELPHIA, PA19111-5096.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594302TABLE I. MATERIAL COMBINATION S

5、YMBOLS AND STRENGTHSSYMBOL MATERIAL COMBINATION RIVETDIAMINIMUMSHEARLOADLBSMINIMUMTENSIONLOADLBSHOLLOW COREA Body: 5056 Al Alloy(UNS A95056)Mandrel: 1012-1025 Steel(UNS G10120-G10250)1045-1075 Steel(UNS G10450-G10750).125.156.188.2503054305759003856058401100C Body: 1100 Al Alloy(UNS A91100)Mandrel:

6、2024 Al Alloy(UNS A92024).125.156.188105155220150240310FILLED COREABody: 5056 Al Alloy(UNS A95056)Mandrel: 1012-1025 Steel(UNS G10120-G10250)1045-1075 Steel(UNS G10450-G10750).125.156.188480590890280480840TABLE II. BASIC DIMENSIONSBASIC DIMENSIONSW REFMATL CODENOMDIA D HEREFRMAXA CRECOMMENDEDHOLE SI

7、ZE.125 .128.124.248.224.051.031.025 .064 .072 .129-.133.156 .159.154.327.297.066.046.025 .086 .090 .160-.164.188 .191.186.393.357.081.061.025 .104 .108 .192-.196.250 .255.249.525.475.099.079.025 .144 - .257-.261Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

8、 IHS-,-,-A-A-594303TABLE III. DASH NUMBERS AND DIMENSIONSMATERIAL COMBINATIONSHOLLOW CORE FILLEDCOREA C A L PMINRECOMMENDEDGRIP RANGEA401HA402HA403HA404HA405HA406HC402HC403HC404HA401FA402FA403F.222-.252.286-.316.347-.377.410-.440.472-.502.535-.5651.00.032-.062.063-.125.126-.187.188-.250.251-.312.313

9、-.375A502HA503HA505HC504HA502FA503FA505F.300-.330.362-.392.425-.455.487-.5171.00.063-.125.126-.187.188-.250.251-.312A602HA604HA606HA608HC602HC604HC606HA602FA604FA606F.315-.345.440-.470.565-.595.690-.7201.00.063-.125.126-.250.251-.375.376-.500A804H .465-.505 1.00 .126-.250Provided by IHSNot for Resal

10、eNo reproduction or networking permitted without license from IHS-,-,-A-A-5943042.2 Materials shall be of the type and grade specified in Table I.2.3 Workmanship. Rivets shall be of uniform quality and free from injurious seams and other injurious defects.2.4 Single shear load. The shear test shall

11、be performed in accordance with Test Method 20 of NASM1312, orequivalent and shall conform to the data specified in Table I.2.5 Tension load. The tension test shall be performed in accordance with Test Method 8 of NASM1312, orequivalent and shall conform to the data specified in Table I.2.6 Packagin

12、g requirements The requirements for packaging shall be in accordance with ASTM D3951.3. QUALITY ASSURANCE PROVISIONS.3.1 Product conformance. The products provided shall meet the salient characteristics of this commercial itemdescription, conform to the producers own drawings, specifications, standa

13、rds, and the quality assurance practices,and be the same product offered for sale in the commercial market. The government reserves the right to requireproof of such conformance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5943054. NOTES4.1 Al

14、l dimensions are in inches.4.2 The part number shall consist of the basic Commercial Item Description Number followed by a dash numberfrom Table III. The dash number consists of a material combination symbol from Table I, a nominal bodydiameter size code in thirty-seconds of an inch from Table II, a

15、 maximum grip code in sixteenths of an inch fromTable III, and a core style code from Table III.EXAMPLE: AA59430 A 5 03 FCore styleGrip Range CodeNominal DiameterMaterialCommercial Item Description NumberAA59430A503 Indicates - Rivet, blind, nonstructural, retainedmandrel, closed-end, domed head,505

16、6 (UNS A95056) aluminum alloy body,C1012-C1025 (UNS G10120-G10250) orC1045-C1075 (UNS G10450-G10750) steelmandrel; nominal body diameter size, .156;grip range, .126-.187,style; filled core.Military Interests:Custodians: Preparing Activity:Army - AR DLA-ISNavy - ASAir Force - 99Review Activities: (Pr

17、oject No. 5320-0959)Army - AV, MIAir Force - 11, 82National Security Agency-NSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3 and 8. In bl

18、ock 1, both the document number and revision letter should be given.2. The submitter of this form must complete blocks 4, 5, 6 and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of documents, or to request wa

19、ivers, or clarification of requirements on current contracts.Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-594302. DOCUMENT DATE (YYMMDD)9904203. DOCUMENT

20、 TITLE:RIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL, CLOSED-END, DOMED HEAD, ALUMINUM ALLOY4. NATURE OF CHANGE5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(2) AUTOVON (If app

21、licable)7. DATE SUBMITTED (YYMMDD)8. PREPARING ACTIVITY DLA-ISa. NAMEEmelia Altomarib. TELEPHONE (Include Area Code)(1) Commercial (215) 697-6827(2) (DSN) 442-6827c. ADDRESS (Include Zip Code)Defense Industrial Supply Center700 Robbins AvenueBldg. 3 (Code DISC-AESD)Philadelphia, PA 19111-5096IF YOU

22、DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT:Defense Quality and Standardization Office5203 Leesburg Pike, Suite 1403Falls Church, VA 22041TELEPHONE (703) 756-2340 AUTOVON 289-2340DD Form 1426, OCT 89 Previous editions are obsolete. 198/290Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-